/* $OpenBSD: vme.c,v 1.27 2003/12/28 19:44:26 miod Exp $ */ /* * Copyright (c) 1999 Steve Murphree, Jr. * Copyright (c) 1995 Theo de Raadt * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "pcctwo.h" #include "syscon.h" #include #if NSYSCON > 0 #include #endif int vmematch(struct device *, void *, void *); void vmeattach(struct device *, struct device *, void *); void vme2chip_init(struct vmesoftc *); u_long vme2chip_map(u_long, int, int); int vme2abort(void *); int sysconabort(void *); int vmeprint(void *, const char *); void *vmemap(struct vmesoftc *sc, off_t vmeaddr, int len, int bustype); void vmeunmap(void *, int); void vmesyscon_init(struct vmesoftc *); int vmebustype; int vmevecbase; struct vme2reg *sys_vme2; struct cfattach vme_ca = { sizeof(struct vmesoftc), vmematch, vmeattach }; struct cfdriver vme_cd = { NULL, "vme", DV_DULL, 0 }; int vmematch(parent, cf, args) struct device *parent; void *cf; void *args; { return (1); } /* * make local addresses 1G-2G correspond to VME addresses 3G-4G, * as D32 */ #define VME2_D32STARTPHYS (1*1024*1024*1024UL) #define VME2_D32ENDPHYS (2*1024*1024*1024UL) #define VME2_D32STARTVME (3*1024*1024*1024UL) #define VME2_D32BITSVME (3*1024*1024*1024UL) /* * make local addresses 3G-3.75G correspond to VME addresses 3G-3.75G, * as D16 */ #define VME2_D16STARTPHYS (3*1024*1024*1024UL) #define VME2_D16ENDPHYS (3*1024*1024*1024UL + 768*1024*1024UL) #define VME2_A32D16STARTPHYS (0xFF000000UL) #define VME2_A32D16ENDPHYS (0xFF7FFFFFUL) /* * Returns a physical address mapping for a VME address & length. * Note: on some hardware it is not possible to create certain * mappings, ie. the MVME147 cannot do 32 bit accesses to VME bus * addresses from 0 to physmem. */ void * vmepmap(sc, vmeaddr, len, bustype) struct device *sc; off_t vmeaddr; int len; int bustype; { u_int32_t base = (u_int32_t)vmeaddr; len = roundup(len, NBPG); switch (vmebustype) { #if NPCCTWO > 0 || NSYSCON > 0 case BUS_PCCTWO: case BUS_SYSCON: switch (bustype) { case BUS_VMES: /* D16 VME Transfers */ #ifdef DEBUG printf("base 0x%8llx/0x%8x len 0x%x\n", vmeaddr, base, len); #endif base = vme2chip_map(base, len, 16); if (base == NULL) { printf("%s: cannot map pa 0x%x len 0x%x\n", sc->dv_xname, base, len); return (NULL); } break; case BUS_VMEL: /* D32 VME Transfers */ #ifdef DEBUG printf("base 0x%8llx/0x%8x len 0x%x\n", vmeaddr, base, len); #endif base = vme2chip_map(base, len, 32); if (base == NULL) { printf("%s: cannot map pa 0x%x len 0x%x\n", sc->dv_xname, base, len); return (NULL); } break; } break; #endif } return ((void *)base); } /* if successful, returns the va of a vme bus mapping */ void * vmemap(sc, vmeaddr, len, bustype) struct vmesoftc *sc; off_t vmeaddr; int len; int bustype; { void *pa, *va; pa = vmepmap((struct device *)sc, vmeaddr, len, bustype); if (pa == NULL) return (NULL); va = mapiodev(pa, len); return (va); } void vmeunmap(va, len) void *va; int len; { unmapiodev(va, len); } int vmerw(sc, uio, flags, bus) struct device *sc; struct uio *uio; int flags; int bus; { vaddr_t v; int c; struct iovec *iov; void *vme; int error = 0; while (uio->uio_resid > 0 && error == 0) { iov = uio->uio_iov; if (iov->iov_len == 0) { uio->uio_iov++; uio->uio_iovcnt--; if (uio->uio_iovcnt < 0) panic("vmerw"); continue; } v = uio->uio_offset; c = min(iov->iov_len, MAXPHYS); if ((v & PGOFSET) + c > NBPG) /* max NBPG at a time */ c = NBPG - (v & PGOFSET); if (c == 0) return (0); vme = vmemap((struct vmesoftc *)sc, v & ~PGOFSET, NBPG, BUS_VMES); if (vme == NULL) { error = EFAULT; /* XXX? */ continue; } error = uiomove((void *)vme + (v & PGOFSET), c, uio); vmeunmap(vme, NBPG); } return (error); } int vmeprint(args, bus) void *args; const char *bus; { struct confargs *ca = args; printf(" addr 0x%x", ca->ca_offset); if (ca->ca_vec > 0) printf(" vec 0x%x", ca->ca_vec); if (ca->ca_ipl > 0) printf(" ipl %d", ca->ca_ipl); return (UNCONF); } int vmescan(parent, child, args, bustype) struct device *parent; void *child, *args; int bustype; { struct cfdata *cf = child; struct vmesoftc *sc = (struct vmesoftc *)parent; struct confargs oca; size_t len; if (parent->dv_cfdata->cf_driver->cd_indirect) { printf(" indirect devices not supported\n"); return 0; } bzero(&oca, sizeof oca); oca.ca_bustype = bustype; oca.ca_paddr = (void *)cf->cf_loc[0]; oca.ca_len = cf->cf_loc[1]; oca.ca_vec = cf->cf_loc[2]; oca.ca_ipl = cf->cf_loc[3]; if (oca.ca_ipl > 0 && oca.ca_vec == -1) oca.ca_vec = vme_findvec(); if (oca.ca_len == -1) oca.ca_len = PAGE_SIZE; len = oca.ca_len; oca.ca_offset = (u_int)oca.ca_paddr; oca.ca_vaddr = vmemap(sc, (vaddr_t)oca.ca_paddr, oca.ca_len, oca.ca_bustype); if (oca.ca_vaddr == NULL) oca.ca_vaddr = (void *)-1; /* XXX */ oca.ca_master = (void *)sc; oca.ca_name = cf->cf_driver->cd_name; if ((*cf->cf_attach->ca_match)(parent, cf, &oca) == 0) { if (oca.ca_vaddr != (void *)-1) vmeunmap(oca.ca_vaddr, len); return (0); } /* * Map the whole space the driver is interested in. */ if (len != oca.ca_len) { vmeunmap(oca.ca_vaddr, len); if (oca.ca_len != 0) { if (vmemap(sc, (vaddr_t)oca.ca_paddr, oca.ca_len, oca.ca_bustype) == NULL) { printf("%s: can't map VME space\n", oca.ca_name); return (0); } } } config_attach(parent, cf, &oca, vmeprint); return (1); } void vmeattach(parent, self, args) struct device *parent, *self; void *args; { struct vmesoftc *sc = (struct vmesoftc *)self; struct confargs *ca = args; sc->sc_vaddr = ca->ca_vaddr; vmebustype = ca->ca_bustype; switch (ca->ca_bustype) { #if NPCCTWO > 0 case BUS_PCCTWO: { struct vme2reg *vme2; vme2 = (struct vme2reg *)sc->sc_vaddr; /* Sanity check that the Bug is set up right */ if (VME2_GET_VBR1(vme2) >= 0xF0) { panic("Correct the VME Vector Base Registers in the Bug ROM.\nSuggested values are 0x60 for VME Vec0 and 0x70 for VME Vec1."); } vmevecbase = VME2_GET_VBR1(vme2) + 0x10; printf(": vector base 0x%x", vmevecbase); if (vme2->vme2_tctl & VME2_TCTL_SCON) printf(", system controller"); printf("\n"); vme2chip_init(sc); } break; #endif #if NSYSCON > 0 case BUS_SYSCON: { u_int8_t sconc; vmevecbase = 0x80; /* Hard coded for MVME188 */ sconc = *(volatile u_int8_t *)GLOBAL1; if (ISSET(sconc, M188_SYSCON)) printf(": system controller"); printf("\n"); vmesyscon_init(sc); } break; #endif } while (config_found(self, NULL, NULL)) ; } /* find a VME vector based on what is in NVRAM settings. */ int vme_findvec(void) { return(intr_findvec(vmevecbase, 0xFF)); } /* * On the VMEbus, only one cpu may be configured to respond to any * particular vme ipl. Therefore, it wouldn't make sense to globally * enable all the interrupts all the time -- it would not be possible * to put two cpu's and one vme card into a single cage. Rather, we * enable each vme interrupt only when we are attaching a device that * uses it. This makes it easier (though not trivial) to put two cpu * cards in one VME cage, and both can have some limited access to vme * interrupts (just can't share the same irq). * Obviously no check is made to see if another cpu is using that * interrupt. If you share you will lose. */ /* * All VME bus devices will use a vector starting with VBR1 + 0x10 * and determined by intr_findvec(). (in machdep.c) vmeintr_establish() * should be called with the 'vec' argument = 0 to 'auto vector' a * VME device. * * The 8 SW interrupters will start with VBR1. The rest will start * with VBR0< 4) & 0xFF. */ int vmeintr_establish(vec, ih) int vec; struct intrhand *ih; { struct vmesoftc *sc = (struct vmesoftc *) vme_cd.cd_devs[0]; #if NPCCTWO > 0 struct vme2reg *vme2; #endif #if NSYSCON > 0 struct sysconreg *syscon; #endif int x; switch (vmebustype) { #if NPCCTWO > 0 case BUS_PCCTWO: vme2 = (struct vme2reg *)sc->sc_vaddr; vme2->vme2_irqen = vme2->vme2_irqen | VME2_IRQ_VME(ih->ih_ipl); break; #endif #if NSYSCON > 0 case BUS_SYSCON: syscon = (struct sysconreg *)sc->sc_vaddr; break; #endif } x = (intr_establish(vec, ih)); return (x); } #if NPCCTWO > 0 void vme2chip_init(sc) struct vmesoftc *sc; { struct vme2reg *vme2 = (struct vme2reg *)sc->sc_vaddr; u_long ctl; sys_vme2 = vme2; /* turn off SYSFAIL LED */ vme2->vme2_tctl &= ~VME2_TCTL_SYSFAIL; ctl = vme2->vme2_masterctl; printf("%s: using BUG parameters\n", sc->sc_dev.dv_xname); /* setup a A32D16 space */ printf("%s: 1phys 0x%08lx-0x%08lx to VME 0x%08lx-0x%08lx\n", sc->sc_dev.dv_xname, vme2->vme2_master1 << 16, vme2->vme2_master1 & 0xffff0000, vme2->vme2_master1 << 16, vme2->vme2_master1 & 0xffff0000); /* setup a A32D32 space */ printf("%s: 2phys 0x%08lx-0x%08lx to VME 0x%08lx-0x%08lx\n", sc->sc_dev.dv_xname, vme2->vme2_master2 << 16, vme2->vme2_master2 & 0xffff0000, vme2->vme2_master2 << 16, vme2->vme2_master2 & 0xffff0000); /* setup a A24D16 space */ printf("%s: 3phys 0x%08lx-0x%08lx to VME 0x%08lx-0x%08lx\n", sc->sc_dev.dv_xname, vme2->vme2_master3 << 16, vme2->vme2_master3 & 0xffff0000, vme2->vme2_master3 << 16, vme2->vme2_master3 & 0xffff0000); /* setup a XXXXXX space */ printf("%s: 4phys 0x%08lx-0x%08lx to VME 0x%08lx-0x%08lx\n", sc->sc_dev.dv_xname, vme2->vme2_master4 << 16, vme2->vme2_master4 & 0xffff0000, (vme2->vme2_master4 << 16) + (vme2->vme2_master4mod << 16), (vme2->vme2_master4 & 0xffff0000) + (vme2->vme2_master4 & 0xffff0000)); /* * Map the VME irq levels to the cpu levels 1:1. * This is rather inflexible, but much easier. */ vme2->vme2_irql4 = (7 << VME2_IRQL4_VME7SHIFT) | (6 << VME2_IRQL4_VME6SHIFT) | (5 << VME2_IRQL4_VME5SHIFT) | (4 << VME2_IRQL4_VME4SHIFT) | (3 << VME2_IRQL4_VME3SHIFT) | (2 << VME2_IRQL4_VME2SHIFT) | (1 << VME2_IRQL4_VME1SHIFT); printf("%s: vme to cpu irq level 1:1\n",sc->sc_dev.dv_xname); /* printf("%s: vme2_irql4 = 0x%08x\n", sc->sc_dev.dv_xname, vme2->vme2_irql4); */ /* Enable the reset switch */ vme2->vme2_tctl |= VME2_TCTL_RSWE; /* Set Watchdog timeout to about 1 minute */ vme2->vme2_tcr |= VME2_TCR_64S; /* Enable VMEChip2 Interrupts */ vme2->vme2_vbr |= VME2_IOCTL1_MIEN; /* * Map the Software VME irq levels to the cpu level 7. */ vme2->vme2_irql3 = (7 << VME2_IRQL3_SW7SHIFT) | (7 << VME2_IRQL3_SW6SHIFT) | (7 << VME2_IRQL3_SW5SHIFT) | (7 << VME2_IRQL3_SW4SHIFT) | (7 << VME2_IRQL3_SW3SHIFT) | (7 << VME2_IRQL3_SW2SHIFT) | (7 << VME2_IRQL3_SW1SHIFT) | (7 << VME2_IRQL3_SW0SHIFT); /* * pseudo driver, abort interrupt handler */ sc->sc_abih.ih_fn = vme2abort; sc->sc_abih.ih_arg = 0; sc->sc_abih.ih_wantframe = 1; sc->sc_abih.ih_ipl = IPL_NMI; intr_establish(110, &sc->sc_abih); vme2->vme2_irqen |= VME2_IRQ_AB; /* * Enable ACFAIL interrupt, but disable Timer 1 interrupt - we * prefer it without for delay(). */ vme2->vme2_irqen = (vme2->vme2_irqen | VME2_IRQ_ACF) & ~VME2_IRQ_TIC1; } #endif /* NPCCTWO */ #if NSYSCON > 0 void vmesyscon_init(sc) struct vmesoftc *sc; { #ifdef TODO struct sysconreg *syscon = (struct sysconreg *)sc->sc_vaddr; u_long ctl; /* turn off SYSFAIL LED */ vme2->vme2_tctl &= ~VME2_TCTL_SYSFAIL; ctl = vme2->vme2_masterctl; printf("%s: using BUG parameters\n", sc->sc_dev.dv_xname); printf("%s: 1phys 0x%08x-0x%08x to VME 0x%08x-0x%08x master\n", sc->sc_dev.dv_xname, vme2->vme2_master1 << 16, vme2->vme2_master1 & 0xffff0000, vme2->vme2_master1 << 16, vme2->vme2_master1 & 0xffff0000); printf("%s: 2phys 0x%08x-0x%08x to VME 0x%08x-0x%08x slave\n", sc->sc_dev.dv_xname, vme2->vme2_master2 << 16, vme2->vme2_master2 & 0xffff0000, vme2->vme2_master2 << 16, vme2->vme2_master2 & 0xffff0000); /* * pseudo driver, abort interrupt handler */ sc->sc_abih.ih_fn = sysconabort; sc->sc_abih.ih_arg = 0; sc->sc_abih.ih_wantframe = 1; sc->sc_abih.ih_ipl = IPL_NMI; intr_establish(110, &sc->sc_abih); #endif /* TODO */ } #endif /* NSYSCON */ /* * A32 accesses on the MVME1[6789]x require setting up mappings in * the VME2 chip. * XXX VME address must be between 2G and 4G * XXX We only support D32 at the moment.. * XXX smurph - This is bogus, get rid of it! Should check vme/syson for offsets. */ u_long vme2chip_map(base, len, dwidth) u_long base; int len, dwidth; { switch (dwidth) { case 16: break; case 32: if (base < VME2_D32STARTPHYS || base + (u_long)len > VME2_D32ENDPHYS) return (NULL); break; } return (base); } #if NPCCTWO > 0 int vme2abort(eframe) void *eframe; { struct frame *frame = eframe; struct vmesoftc *sc = (struct vmesoftc *) vme_cd.cd_devs[0]; struct vme2reg *vme2 = (struct vme2reg *)sc->sc_vaddr; int rc = 0; if (vme2->vme2_irqstat & VME2_IRQ_AB) { vme2->vme2_irqclr = VME2_IRQ_AB; nmihand(frame); rc = 1; } if (vme2->vme2_irqstat & VME2_IRQ_AB) { vme2->vme2_irqclr = VME2_IRQ_AB; nmihand(frame); rc = 1; } #if 0 if (vme2->vme2_irqstat & VME2_IRQ_AB == 0) { printf("%s: abort irq not set\n", sc->sc_dev.dv_xname); return (0); } #endif vme2->vme2_irqclr = VME2_IRQ_AB; nmihand(frame); return (1); } #endif