#
# $OpenBSD: COYOTE,v 1.10 1997/09/26 16:47:42 kstailey Exp $
#

#
# Sun3 3/60M
#

include "arch/sun3/conf/std.sun3"

# Machines to be supported by this kernel
#option 	FPU_EMULATE
#option 	HAVECACHE		# Sun3/260 VAC

# Needs to be set per system.  i.e change these as you see fit
maxusers	4

# Standard system options
option	 	KTRACE				# system call tracing support

# Debugging options.  Uncomment either this:
option	 	DDB
# ... or these two: (for KGDB on another machine)
#makeoptions DEBUG="-g"			# symbols for kgdb + nm
#option 	KGDB

# Filesystem options
option	 	NFSCLIENT			# nfs client support
#
option		FFS		# fast filesystem
option		MFS		# memory-based filesystem
#option 	FDESC		# /dev/fd/* (depreciated)
option	 	FIFO		# FIFOs; RECOMMENDED
option	 	KERNFS		# /kern
#option 	NULLFS		# loopback file system
option	 	PROCFS		# /proc
#option 	UNION		# union file system (merged directories)
#option 	PORTAL		# dynamically created filesystem objects

# Networking options
option	 	INET		# IP prototol stack support
option		GATEWAY		# IP packet forwarding
option		IPFILTER	# IP packet filter for security and NAT
option		IPFILTER_LOG	# use /dev/ipl to log IPF
# XXX - Work-around for root on slow SunOS/Sun3 servers (sigh...)
#option	 	NFS_BOOT_RWSIZE=1024

# Compatability options
#option 	COMPAT_SUNOS	# can run SunOS 4.1.1 executables
#option 	COMPAT_09	# NetBSD 0.9,
option	 	COMPAT_10	# NetBSD 1.0,
option	 	COMPAT_11	# NetBSD 1.1,
option	 	COMPAT_43	# and 4.3BSD
#option 	TCP_COMPAT_42	# TCP bug compatibility with 4.2BSD
option		SYSVSHM		# SysV shared mem compatibility
#option		SYSVMSG		# SysV message queue compatibility
#option		SYSVSEM		# SysV semaphore compatibility

# Sun3-specific debugging options
#option 	PMAP_DEBUG
#option 	VMFAULT_TRACE
#option 	SYSCALL_DEBUG
#option 	EXEC_DEBUG
option	 	DIAGNOSTIC

#config		bsd root on nfs swap on nfs
config		bsd root on sd0 swap on sd0 dumps on sd0

#
# Serial ports
#
zstty0 at zsc1 channel 0	# ttya
zstty1 at zsc1 channel 1	# ttyb

kbd0   at zsc0 channel 0	# keyboard
ms0    at zsc0 channel 1	# mouse

#
# Network devices
#

# Lance Ethernet (only onboard)
le0 at obio0 addr   0x120000 level 3

# Sun3 "si" SCSI controller (NCR 5380)
# This driver has several flags which may be enabled by OR'ing
# the values and using the "flags" directive.  (PR#1929)
# Valid flags are:
#
#	0x01		Use DMA (may be polled)
#	0x02		Use DMA completion interrupts
#	0x04		Allow disconnect/reselect
#
# E.g. "flags 0x07" would enable DMA, interrupts, and reselect.
# Note: these values are quite a bit paranoid...
si0 at obio0 addr   0x140000 level 2 flags 0

#
# SCSI infrastructure
#
scsibus* at scsi?

# Sun incompatible scsi device mappings
sd* at scsibus? target ? lun ?

#
# Frame buffer devices
#

bwtwo0 at obmem0 addr ?

# Misc.
pseudo-device	loop	1		# network loopback
pseudo-device	bpfilter 2		# packet filter
#pseudo-device	sl	2		# CSLIP
pseudo-device	ppp	1		# PPP
#pseudo-device	tun	2		# network tunneling over tty

pseudo-device	pty	32		# pseudo-terminals
#pseudo-device	vnd	4		# paging to files