# # $OpenBSD: COYOTE,v 1.9 1997/07/25 04:40:48 kstailey Exp $ # # # Sun3 3/60M # include "arch/sun3/conf/std.sun3" # Machines to be supported by this kernel #option FPU_EMULATE #option HAVECACHE # Sun3/260 VAC # Needs to be set per system. i.e change these as you see fit maxusers 4 # Standard system options option KTRACE # system call tracing support # Debugging options. Uncomment either this: option DDB # ... or these two: (for KGDB on another machine) #makeoptions DEBUG="-g" # symbols for kgdb + nm #option KGDB # Filesystem options option NFSCLIENT # nfs client support # option FFS # fast filesystem option MFS # memory-based filesystem #option FDESC # /dev/fd/* (depreciated) option FIFO # FIFOs; RECOMMENDED option KERNFS # /kern #option NULLFS # loopback file system option PROCFS # /proc #option UNION # union file system (merged directories) #option PORTAL # union file system (run programs via open(2)) # Networking options option INET # IP prototol stack support option GATEWAY # IP packet forwarding option IPFILTER # IP packet filter for security and NAT option IPFILTER_LOG # use /dev/ipl to log IPF # XXX - Work-around for root on slow SunOS/Sun3 servers (sigh...) #option NFS_BOOT_RWSIZE=1024 # Compatability options #option COMPAT_SUNOS # can run SunOS 4.1.1 executables #option COMPAT_09 # NetBSD 0.9, option COMPAT_10 # NetBSD 1.0, option COMPAT_11 # NetBSD 1.1, option COMPAT_43 # and 4.3BSD #option TCP_COMPAT_42 # TCP bug compatibility with 4.2BSD option SYSVSHM # SysV shared mem compatibility #option SYSVMSG # SysV message queue compatibility #option SYSVSEM # SysV semaphore compatibility # Sun3-specific debugging options #option PMAP_DEBUG #option VMFAULT_TRACE #option SYSCALL_DEBUG #option EXEC_DEBUG option DIAGNOSTIC #config bsd root on nfs swap on nfs config bsd root on sd0 swap on sd0 dumps on sd0 # # Serial ports # zstty0 at zsc1 channel 0 # ttya zstty1 at zsc1 channel 1 # ttyb kbd0 at zsc0 channel 0 # keyboard ms0 at zsc0 channel 1 # mouse # # Network devices # # Lance Ethernet (only onboard) le0 at obio0 addr 0x120000 level 3 # Sun3 "si" SCSI controller (NCR 5380) # This driver has several flags which may be enabled by OR'ing # the values and using the "flags" directive. (PR#1929) # Valid flags are: # # 0x01 Use DMA (may be polled) # 0x02 Use DMA completion interrupts # 0x04 Allow disconnect/reselect # # E.g. "flags 0x07" would enable DMA, interrupts, and reselect. # Note: these values are quite a bit paranoid... si0 at obio0 addr 0x140000 level 2 flags 0 # # SCSI infrastructure # scsibus* at scsi? # Sun incompatible scsi device mappings sd* at scsibus? target ? lun ? # # Frame buffer devices # bwtwo0 at obmem0 addr ? # Misc. pseudo-device loop 1 # network loopback pseudo-device bpfilter 2 # packet filter #pseudo-device sl 2 # CSLIP pseudo-device ppp 1 # PPP #pseudo-device tun 2 # network tunneling over tty pseudo-device pty 32 # pseudo-terminals #pseudo-device vnd 4 # paging to files