/* $OpenBSD: si_obio.c,v 1.10 2001/01/25 03:50:49 todd Exp $ */ /* $NetBSD: si_obio.c,v 1.7 1996/11/20 18:57:00 gwr Exp $ */ /*- * Copyright (c) 1996 The NetBSD Foundation, Inc. * All rights reserved. * * This code is derived from software contributed to The NetBSD Foundation * by Adam Glass, David Jones, and Gordon W. Ross. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. All advertising materials mentioning features or use of this software * must display the following acknowledgement: * This product includes software developed by the NetBSD * Foundation, Inc. and its contributors. * 4. Neither the name of The NetBSD Foundation nor the names of its * contributors may be used to endorse or promote products derived * from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. */ /* * This file contains only the machine-dependent parts of the * Sun3 SCSI driver. (Autoconfig stuff and DMA functions.) * The machine-independent parts are in ncr5380sbc.c * * Supported hardware includes: * Sun SCSI-3 on OBIO (Sun3/50,Sun3/60) * Sun SCSI-3 on VME (Sun3/160,Sun3/260) * * Could be made to support the Sun3/E if someone wanted to. * * Note: Both supported variants of the Sun SCSI-3 adapter have * some really unusual "features" for this driver to deal with, * generally related to the DMA engine. The OBIO variant will * ignore any attempt to write the FIFO count register while the * SCSI bus is in DATA_IN or DATA_OUT phase. This is dealt with * by setting the FIFO count early in COMMAND or MSG_IN phase. * * The VME variant has a bit to enable or disable the DMA engine, * but that bit also gates the interrupt line from the NCR5380! * Therefore, in order to get any interrupt from the 5380, (i.e. * for reselect) one must clear the DMA engine transfer count and * then enable DMA. This has the further complication that you * CAN NOT touch the NCR5380 while the DMA enable bit is set, so * we have to turn DMA back off before we even look at the 5380. * * What wonderfully whacky hardware this is! * * Credits, history: * * David Jones wrote the initial version of this module, which * included support for the VME adapter only. (no reselection). * * Gordon Ross added support for the OBIO adapter, and re-worked * both the VME and OBIO code to support disconnect/reselect. * (Required figuring out the hardware "features" noted above.) * * The autoconfiguration boilerplate came from Adam Glass. */ /***************************************************************** * OBIO functions for DMA ****************************************************************/ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #ifndef DDB #define Debugger() #endif #define DEBUG XXX #include #include #include "sireg.h" #include "sivar.h" #include "am9516.h" /* * How many uS. to delay after touching the am9516 UDC. */ #define UDC_WAIT_USEC 5 void si_obio_dma_setup __P((struct ncr5380_softc *)); void si_obio_dma_start __P((struct ncr5380_softc *)); void si_obio_dma_eop __P((struct ncr5380_softc *)); void si_obio_dma_stop __P((struct ncr5380_softc *)); static __inline__ int si_obio_udc_read __P((volatile struct si_regs *, int)); static __inline__ void si_obio_udc_write __P((volatile struct si_regs *, int, int)); /* * New-style autoconfig attachment */ static int si_obio_match __P((struct device *, void *, void *)); static void si_obio_attach __P((struct device *, struct device *, void *)); struct cfattach si_obio_ca = { sizeof(struct si_softc), si_obio_match, si_obio_attach }; /* Options. Interesting values are: 1,3,7 */ /* XXX: Using 1 for now to mask a (pmap?) bug not yet found... */ int si_obio_options = 1; /* XXX */ static int si_obio_match(parent, vcf, args) struct device *parent; void *vcf, *args; { struct confargs *ca = args; /* Make sure there is something there... */ if (bus_peek(ca->ca_bustype, ca->ca_paddr + 1, 1) == -1) return (0); /* Default interrupt priority. */ if (ca->ca_intpri == -1) ca->ca_intpri = 2; return (1); } static void si_obio_attach(parent, self, args) struct device *parent, *self; void *args; { struct si_softc *sc = (struct si_softc *) self; struct ncr5380_softc *ncr_sc = &sc->ncr_sc; struct cfdata *cf = self->dv_cfdata; struct confargs *ca = args; /* Get options from config flags... */ sc->sc_options = cf->cf_flags | si_obio_options; printf(": options=%d\n", sc->sc_options); sc->sc_adapter_type = ca->ca_bustype; sc->sc_regs = (struct si_regs *) obio_alloc(ca->ca_paddr, sizeof(struct si_regs)); /* * MD function pointers used by the MI code. */ ncr_sc->sc_pio_out = ncr5380_pio_out; ncr_sc->sc_pio_in = ncr5380_pio_in; ncr_sc->sc_dma_alloc = si_dma_alloc; ncr_sc->sc_dma_free = si_dma_free; ncr_sc->sc_dma_setup = si_obio_dma_setup; ncr_sc->sc_dma_start = si_obio_dma_start; ncr_sc->sc_dma_poll = si_dma_poll; ncr_sc->sc_dma_eop = si_obio_dma_eop; ncr_sc->sc_dma_stop = si_obio_dma_stop; ncr_sc->sc_intr_on = NULL; ncr_sc->sc_intr_off = NULL; /* Need DVMA-capable memory for the UDC command block. */ sc->sc_dmacmd = dvma_malloc(sizeof (struct udc_table)); /* Attach interrupt handler. */ isr_add_autovect(si_intr, (void *)sc, ca->ca_intpri); /* Do the common attach stuff. */ si_attach(sc); } static __inline__ void si_obio_udc_write(si, regnum, value) volatile struct si_regs *si; int regnum, value; { si->udc_addr = regnum; delay(UDC_WAIT_USEC); si->udc_data = value; delay(UDC_WAIT_USEC); } static __inline__ int si_obio_udc_read(si, regnum) volatile struct si_regs *si; int regnum; { int value; si->udc_addr = regnum; delay(UDC_WAIT_USEC); value = si->udc_data; delay(UDC_WAIT_USEC); return (value); } /* * This function is called during the COMMAND or MSG_IN phase * that preceeds a DATA_IN or DATA_OUT phase, in case we need * to setup the DMA engine before the bus enters a DATA phase. * * The OBIO "si" IGNORES any attempt to set the FIFO count * register after the SCSI bus goes into any DATA phase, so * this function has to setup the evil FIFO logic. */ void si_obio_dma_setup(ncr_sc) struct ncr5380_softc *ncr_sc; { struct si_softc *sc = (struct si_softc *)ncr_sc; struct sci_req *sr = ncr_sc->sc_current; struct si_dma_handle *dh = sr->sr_dma_hand; volatile struct si_regs *si = sc->sc_regs; struct udc_table *cmd; long data_pa, cmd_pa; int xlen; /* * Get the DVMA mapping for this segment. * XXX - Should separate allocation and mapin. */ data_pa = dvma_kvtopa(dh->dh_dvma, sc->sc_adapter_type); data_pa += (ncr_sc->sc_dataptr - dh->dh_addr); if (data_pa & 1) panic("si_dma_start: bad pa=0x%lx", data_pa); xlen = ncr_sc->sc_datalen; sc->sc_reqlen = xlen; /* XXX: or less? */ #ifdef DEBUG if (si_debug & 2) { printf("si_dma_setup: dh=%p, pa=0x%lx, xlen=0x%x\n", dh, data_pa, xlen); } #endif /* Reset the UDC. (In case not already reset?) */ si_obio_udc_write(si, UDC_ADR_COMMAND, UDC_CMD_RESET); /* Reset the FIFO */ si->si_csr &= ~SI_CSR_FIFO_RES; /* active low */ si->si_csr |= SI_CSR_FIFO_RES; /* Set direction (send/recv) */ if (dh->dh_flags & SIDH_OUT) { si->si_csr |= SI_CSR_SEND; } else { si->si_csr &= ~SI_CSR_SEND; } /* Set the FIFO counter. */ si->fifo_count = xlen; /* Reset the UDC. */ si_obio_udc_write(si, UDC_ADR_COMMAND, UDC_CMD_RESET); /* * XXX: Reset the FIFO again! Comment from Sprite: * Go through reset again becuase of the bug on the 3/50 * where bytes occasionally linger in the DMA fifo. */ si->si_csr &= ~SI_CSR_FIFO_RES; /* active low */ si->si_csr |= SI_CSR_FIFO_RES; #ifdef DEBUG /* Make sure the extra FIFO reset did not hit the count. */ if (si->fifo_count != xlen) { printf("si_dma_setup: fifo_count=0x%x, xlen=0x%x\n", si->fifo_count, xlen); Debugger(); } #endif /* * Set up the DMA controller. The DMA controller on * OBIO needs a command block in DVMA space. */ cmd = sc->sc_dmacmd; cmd->addrh = ((data_pa & 0xFF0000) >> 8) | UDC_ADDR_INFO; cmd->addrl = data_pa & 0xFFFF; cmd->count = xlen / 2; /* bytes -> words */ cmd->cmrh = UDC_CMR_HIGH; if (dh->dh_flags & SIDH_OUT) { if (xlen & 1) cmd->count++; cmd->cmrl = UDC_CMR_LSEND; cmd->rsel = UDC_RSEL_SEND; } else { cmd->cmrl = UDC_CMR_LRECV; cmd->rsel = UDC_RSEL_RECV; } /* Tell the DMA chip where the control block is. */ cmd_pa = dvma_kvtopa((long)cmd, BUS_OBIO); si_obio_udc_write(si, UDC_ADR_CAR_HIGH, (cmd_pa & 0xff0000) >> 8); si_obio_udc_write(si, UDC_ADR_CAR_LOW, (cmd_pa & 0xffff)); /* Tell the chip to be a DMA master. */ si_obio_udc_write(si, UDC_ADR_MODE, UDC_MODE); /* Tell the chip to interrupt on error. */ si_obio_udc_write(si, UDC_ADR_COMMAND, UDC_CMD_CIE); /* Will do "start chain" command in _dma_start. */ } void si_obio_dma_start(ncr_sc) struct ncr5380_softc *ncr_sc; { struct si_softc *sc = (struct si_softc *)ncr_sc; struct sci_req *sr = ncr_sc->sc_current; struct si_dma_handle *dh = sr->sr_dma_hand; volatile struct si_regs *si = sc->sc_regs; int s; #ifdef DEBUG if (si_debug & 2) { printf("si_dma_start: sr=%p\n", sr); } #endif /* This MAY be time critical (not sure). */ s = splhigh(); /* Finally, give the UDC a "start chain" command. */ si_obio_udc_write(si, UDC_ADR_COMMAND, UDC_CMD_STRT_CHN); /* * Acknowledge the phase change. (After DMA setup!) * Put the SBIC into DMA mode, and start the transfer. */ if (dh->dh_flags & SIDH_OUT) { *ncr_sc->sci_tcmd = PHASE_DATA_OUT; SCI_CLR_INTR(ncr_sc); *ncr_sc->sci_icmd = SCI_ICMD_DATA; *ncr_sc->sci_mode |= (SCI_MODE_DMA | SCI_MODE_DMA_IE); *ncr_sc->sci_dma_send = 0; /* start it */ } else { *ncr_sc->sci_tcmd = PHASE_DATA_IN; SCI_CLR_INTR(ncr_sc); *ncr_sc->sci_icmd = 0; *ncr_sc->sci_mode |= (SCI_MODE_DMA | SCI_MODE_DMA_IE); *ncr_sc->sci_irecv = 0; /* start it */ } splx(s); ncr_sc->sc_state |= NCR_DOINGDMA; #ifdef DEBUG if (si_debug & 2) { printf("si_dma_start: started, flags=0x%x\n", ncr_sc->sc_state); } #endif } void si_obio_dma_eop(ncr_sc) struct ncr5380_softc *ncr_sc; { /* Not needed - DMA was stopped prior to examining sci_csr */ } void si_obio_dma_stop(ncr_sc) struct ncr5380_softc *ncr_sc; { struct si_softc *sc = (struct si_softc *)ncr_sc; struct sci_req *sr = ncr_sc->sc_current; struct si_dma_handle *dh = sr->sr_dma_hand; volatile struct si_regs *si = sc->sc_regs; int resid, ntrans, tmo, udc_cnt; if ((ncr_sc->sc_state & NCR_DOINGDMA) == 0) { #ifdef DEBUG printf("si_dma_stop: dma not running\n"); #endif return; } ncr_sc->sc_state &= ~NCR_DOINGDMA; NCR_TRACE("si_dma_stop: top, csr=0x%x\n", si->si_csr); /* OK, have either phase mis-match or end of DMA. */ /* Set an impossible phase to prevent data movement? */ *ncr_sc->sci_tcmd = PHASE_INVALID; /* Check for DMA errors. */ if (si->si_csr & (SI_CSR_DMA_CONFLICT | SI_CSR_DMA_BUS_ERR)) { printf("si: DMA error, csr=0x%x, reset\n", si->si_csr); sr->sr_xs->error = XS_DRIVER_STUFFUP; ncr_sc->sc_state |= NCR_ABORTING; si_reset_adapter(ncr_sc); goto out; } /* Note that timeout may have set the error flag. */ if (ncr_sc->sc_state & NCR_ABORTING) goto out; /* * After a read, wait for the FIFO to empty. * Note: this only works on the OBIO version. */ if ((dh->dh_flags & SIDH_OUT) == 0) { tmo = 200000; /* X10 = 2 sec. */ for (;;) { if (si->si_csr & SI_CSR_FIFO_EMPTY) break; if (--tmo <= 0) { printf("si: dma fifo did not empty, reset\n"); ncr_sc->sc_state |= NCR_ABORTING; /* si_reset_adapter(ncr_sc); */ goto out; } delay(10); } } /* * Now try to figure out how much actually transferred * The fifo_count might not reflect how many bytes were * actually transferred. */ resid = si->fifo_count & 0xFFFF; ntrans = sc->sc_reqlen - resid; #ifdef DEBUG if (si_debug & 2) { printf("si_dma_stop: resid=0x%x ntrans=0x%x\n", resid, ntrans); } #endif /* XXX: Treat (ntrans==0) as a special, non-error case? */ if (ntrans < MIN_DMA_LEN) { printf("si: fifo count: 0x%x\n", resid); ncr_sc->sc_state |= NCR_ABORTING; goto out; } if (ntrans > ncr_sc->sc_datalen) panic("si_dma_stop: excess transfer"); /* Adjust data pointer */ ncr_sc->sc_dataptr += ntrans; ncr_sc->sc_datalen -= ntrans; /* * After a read, we may need to clean-up * "Left-over bytes" (yuck!) */ if ((dh->dh_flags & SIDH_OUT) == 0) { /* If odd transfer count, grab last byte by hand. */ if (ntrans & 1) { NCR_TRACE("si_dma_stop: leftover 1 at 0x%x\n", (int) ncr_sc->sc_dataptr - 1); ncr_sc->sc_dataptr[-1] = (si->fifo_data & 0xff00) >> 8; goto out; } /* UDC might not have transferred the last word. */ udc_cnt = si_obio_udc_read(si, UDC_ADR_COUNT); if (((udc_cnt * 2) - resid) == 2) { NCR_TRACE("si_dma_stop: leftover 2 at 0x%x\n", (int) ncr_sc->sc_dataptr - 2); ncr_sc->sc_dataptr[-2] = (si->fifo_data & 0xff00) >> 8; ncr_sc->sc_dataptr[-1] = (si->fifo_data & 0x00ff); } } out: /* Reset the UDC. */ si_obio_udc_write(si, UDC_ADR_COMMAND, UDC_CMD_RESET); si->fifo_count = 0; si->si_csr &= ~SI_CSR_SEND; /* Reset the FIFO */ si->si_csr &= ~SI_CSR_FIFO_RES; /* active low */ si->si_csr |= SI_CSR_FIFO_RES; /* Put SBIC back in PIO mode. */ /* XXX: set tcmd to PHASE_INVALID? */ *ncr_sc->sci_mode &= ~(SCI_MODE_DMA | SCI_MODE_DMA_IE); *ncr_sc->sci_icmd = 0; }