/* $OpenBSD: ts.c,v 1.4 1997/05/29 00:05:08 niklas Exp $ */ /* $NetBSD: ts.c,v 1.11 1997/01/11 11:34:43 ragge Exp $ */ /*- * Copyright (c) 1991 The Regents of the University of California. * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. All advertising materials mentioning features or use of this software * must display the following acknowledgement: * This product includes software developed by the University of * California, Berkeley and its contributors. * 4. Neither the name of the University nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * * @(#)tmscp.c 7.16 (Berkeley) 5/9/91 */ /* * sccsid = "@(#)tmscp.c 1.24 (ULTRIX) 1/21/86"; */ /************************************************************************ * * * Licensed from Digital Equipment Corporation * * Copyright (c) * * Digital Equipment Corporation * * Maynard, Massachusetts * * 1985, 1986 * * All rights reserved. * * * * The Information in this software is subject to change * * without notice and should not be construed as a commitment * * by Digital Equipment Corporation. Digital makes no * * representations about the suitability of this software for * * any purpose. It is supplied "As Is" without expressed or * * implied warranty. * * * * If the Regents of the University of California or its * * licensees modify the software in a manner creating * * diriviative copyright rights, appropriate copyright * * legends may be placed on the drivative work in addition * * to that set forth above. * * * ************************************************************************/ /* * TSV05/TS05 device driver, written by Bertram Barth. * * should be TS11 compatible (untested) */ #define TS11_COMPAT /* don't use extended features provided by TS05 */ #ifdef NEED_18BIT #define TS_UBAFLAGS UBA_NEED16 #else #define TS_UBAFLAGS 0 #endif #define ENABLE_ESS #define ENABLE_END #define ENABLE_EAI /* enable Attention-Interrupts */ #undef ENABLE_EAI #define ENABLE_ERI /* Enable Release Buffer Interrupts */ #undef ENABLE_ERI #ifdef DEBUG int tsdebug = 1; # define debug(x) if (tsdebug > 0) {DELAY(2000); printf x; DELAY(3000);} # define debug10(x) if (tsdebug > 9) printf x #else # define debug(x) /* just ignore it */ # define debug10(x) /* just ignore it */ #endif #ifdef TRACE int tstrace = 1; # define trace(x) if (tstrace > 0) {DELAY(2000); printf x; DELAY(3000);} #else # define trace(x) /* just ignore it */ #endif /* * TODO: most :-) * * include uba-mapping into tsinit(); * merge tsinit(), tsreset() and tsprobe(); * complete tsintr(); * add proper error/status messages * make messages appear where they are intended to. * check for termination-classes and appropriate actions. * check if flags like CVC and ATTN should be used. * look for correct handling of attentions. * check for correct usage of retry-commands. * ... */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "ts.h" /* * ts command packets and communication area (per controller) */ struct ts { struct tsdevice *reg; /* address of i/o-registers */ struct tscmd cmd; /* command packet(s) */ struct tsmsg msg; /* message packet(s) */ } ts[NTS]; /* * Software status, per controller. * also status per tape-unit, since only one unit per controller * (thus we have no struct ts_info) */ struct ts_softc { struct device sc_dev; /* Autoconf ... */ struct uba_unit sc_unit; /* Struct common for UBA to talk */ struct ts *sc_ts; /* Unibus address of uda struct */ short sc_mapped; /* Unibus map allocated ? */ int sc_ubainfo; /* Unibus mapping info */ short sc_state; /* see below: ST_xxx */ short sc_flags; /* see below: FL_xxx */ short sc_lcmd; /* last command word */ short sc_rtc; /* retry count for lcmd */ short sc_lssr; /* last status register */ short sc_lmsgh; /* last message header */ short sc_lxst0; /* last status word */ short sc_cmdf; /* command flags (ack,cvc,ie) */ short sc_openf; /* lock against multiple opens */ short sc_liowf; /* last operation was write */ int sc_micro; /* microcode revision */ int sc_ivec; /* interrupt vector address */ short sc_ipl; /* interrupt priority, Q-bus */ }; void tsintr __P((int)); int tsinit __P((struct ts_softc *)); void tscommand __P((dev_t, int, int)); int tsstatus __P((int)); int tsexec __P((int, int)); int tsstart __P((struct ts_softc *, struct buf *)); int tswchar __P((int)); void tsreset __P((int)); void tsxstatus __P((struct tsmsg *)); int tsmatch __P((struct device *, void *, void *)); void tsattach __P((struct device *, struct device *, void *)); void tsstrategy __P((struct buf *)); int tsopen __P((dev_t, int, int, struct proc *)); int tsclose __P((dev_t, int, int, struct proc *)); int tsioctl __P((dev_t, u_long, caddr_t, int, struct proc *)); int tsread __P((dev_t, struct uio *)); int tswrite __P((dev_t, struct uio *)); int tsdump __P((dev_t, daddr_t, caddr_t, size_t)); struct cfdriver ts_cd = { NULL, "ts", DV_DULL }; struct cfattach ts_ca = { sizeof(struct ts_softc), tsmatch, tsattach }; #define ST_INVALID 0 /* uninitialized, before probe */ #define ST_PROBE 1 /* during tsprobe(), not used */ #define ST_SLAVE 2 /* in tsslave(), init almost complete */ #define ST_ATTACH 3 /* during tsattach(), not used */ #define ST_INITIALIZED 4 /* init completed, set by tsintr() */ #define ST_RUNNING 5 #define ST_IDLE 6 #define ST_BUSY 7 /* Bits in minor device */ #define TS_UNIT(dev) (minor(dev)&03) #define TS_HIDENSITY 010 #define TS_PRI LOG_INFO /* * Since we don't have credits and thus only one operation per time, * we don't have and don't need queues like MSCP/TMSCP use them. * Per controller we only need one internal buffer for ioctls and * two pointers to buffers to simulate similiar behaviour ... */ struct buf ts_cbuf[NTS]; /* internal cmd buffer (for ioctls) */ struct buf *ts_wtab[NTS]; /* dummy I/O wait queue */ #define b_ubinfo b_resid /* Unibus mapping info, per buffer */ /*----------------------------------------------------------------------*/ /* * Initialize a TS device. Set up UBA mapping registers, * initialize data structures, what else ??? */ int tsinit (sc) struct ts_softc *sc; { volatile struct tsdevice *tsregs; int unit = sc->sc_dev.dv_unit; struct uba_unit *uu; uu = &sc->sc_unit; tsregs = (struct tsdevice *)ts[unit].reg; if (sc->sc_mapped == 0) { /* * Map the communications area and command and message * buffer into Unibus address space. */ sc->sc_ubainfo = uballoc((struct uba_softc *) sc->sc_dev.dv_parent, (caddr_t)&ts[unit], sizeof (struct ts), TS_UBAFLAGS); sc->sc_ts = (struct ts *)(UBAI_ADDR(sc->sc_ubainfo)); sc->sc_mapped = 1; } /* * bertram: start hardware initialization ?????? */ /* tsreset(unit); */ return (1); } /* * send a command using the default command-buffer for this unit/controller. * If a command-word is given, then assemble a one-word command. * other words in command-buffer are unchanged and must thus be initialized * before calling this function. */ int tsexec (ctlr, cmd) int ctlr; int cmd; { register struct ts_softc *sc = ts_cd.cd_devs[ctlr]; register struct tscmd *tscmdp = &ts[ctlr].cmd; register long tscmdma = (long)&sc->sc_ts->cmd; /* mapped address */ volatile struct tsdevice *tsreg = ts[ctlr].reg; volatile char *dbx = ((char*)tsreg) + 3; volatile short sr; sc->sc_cmdf |= TS_CF_ACK | TS_CF_IE; tscmdp->cmdr = sc->sc_cmdf | cmd; tscmdp->cmdr = TS_CF_ACK | TS_CF_IE | sc->sc_cmdf | cmd; sc->sc_cmdf = 0; /* XXX */ #ifdef DEBUG switch (tscmdp->cmdr & TS_CF_CMASK) { case TS_CMD_RNF: cmdName = "Read Next (Forward)"; break; case TS_CMD_RPR: cmdName = "Read Previous (Reverse)"; break; case TS_CMD_WCHAR: cmdName = "Write Characteristics"; break; case TS_CMD_WD: cmdName = "Write Data (Next)"; break; case TS_CMD_WDR: cmdName = "Write Data (Retry)"; break; case TS_CMD_SRF: cmdName = "Space Records Forward"; break; case TS_CMD_SRR: cmdName = "Space Records Reverse"; break; case TS_CMD_STMF: cmdName = "Skip Tape Marks Forward"; break; case TS_CMD_STMR: cmdName = "Skip Tape Marks Reverse"; break; case TS_CMD_RWND: cmdName = "Rewind"; break; case TS_CMD_WTM: cmdName = "Write Tape Mark"; break; case TS_CMD_WTMR: cmdName = "Write Tape Mark (Retry)"; break; case TS_CMD_STAT: cmdName = "Get Status (END)"; break; default: cmdName = "unexptected Command"; break; } #endif sr = tsreg->tssr; if ((sr & TS_SSR) == 0) { /* subsystem NOT ready */ printf ("%s%d: subsystem not ready [%x]\n", sc->sc_dev.dv_xname, sr); return (-1); } dbx = ((char*)tsreg) + 3; /* dbx is located at the fourth byte */ *dbx = (tscmdma >> 18) & 0x0F; /* load bits 18-21 into dbx */ /* possible race-condition with ATTN !!! */ sr = tsreg->tssr; if ((sr & TS_RMR) != 0) { /* Register modification Refused */ printf ("ts: error writing TSDBX\n"); return (-1); } /* now load bits 15-2 at pos 15-2 and bits 17,16 at pos 1,0 of TSDB */ tsreg->tsdb = (tscmdma & 0xfffc) | ((tscmdma >> 16) & 0x03); /* * wait for SSR or RMR to show up */ sr = tsreg->tssr; if ((sr & TS_SSR) != 0) { /* something went wrong .. */ if (sr & TS_RMR) { printf ("ts: error writing TSDB (RMR)\n"); return (-1); } if (sr & TS_NXM) { printf ("ts: error writing TSDB (NXM)\n"); return (-1); } printf ("ts: error 0x%x while writing TSDB\n", sr); tsstatus (sr); return (-1); } return (0); /* completed successfully */ } /* * Execute a (ioctl) command on the tape drive a specified number of times. * This routine sets up a buffer and calls the strategy routine which * issues the command to the controller. */ void tscommand (dev, cmd, count) register dev_t dev; int cmd; int count; { register struct buf *bp; register int s; trace (("tscommand (%d, %x, %d)\n", TS_UNIT(dev), cmd, count)); s = splbio(); bp = &ts_cbuf[TS_UNIT(dev)]; while (bp->b_flags & B_BUSY) { /* * This special check is because B_BUSY never * gets cleared in the non-waiting rewind case. ??? */ if (bp->b_bcount == 0 && (bp->b_flags & B_DONE)) break; bp->b_flags |= B_WANTED; sleep ((caddr_t)bp, PRIBIO); /* check MOT-flag !!! */ } bp->b_flags = B_BUSY | B_READ; splx(s); /* * Load the buffer. The b_count field gets used to hold the command * count. the b_resid field gets used to hold the command mneumonic. * These 2 fields are "known" to be "safe" to use for this purpose. * (Most other drivers also use these fields in this way.) */ bp->b_dev = dev; bp->b_bcount = count; bp->b_resid = cmd; bp->b_blkno = 0; tsstrategy (bp); /* * In case of rewind from close, don't wait. * This is the only case where count can be 0. */ if (count == 0) { debug (("tscommand: direct return, no iowait.\n")); return; } debug (("tscommand: calling iowait ...\n"));; iowait (bp); if (bp->b_flags & B_WANTED) wakeup ((caddr_t)bp); bp->b_flags &= B_ERROR; } /* * Start an I/O operation on TS05 controller */ int tsstart (sc, bp) register struct ts_softc *sc; register struct buf *bp; { int ctlr = sc->sc_dev.dv_unit; volatile struct tsdevice *tsreg = ts[ctlr].reg; register struct tscmd *tscmdp = &ts[ctlr].cmd; register struct buf *dp; volatile int i, itmp; int ioctl; int cmd; if ((dp = ts_wtab[ctlr]) != NULL) { /* * There's already a command pending ... * Either we are called by tsintr or we have missed * something important (race condition). */ /* bertram: ubarelse ??? */ ts_wtab[ctlr] = NULL; dp->b_flags |= B_ERROR; iodone (dp); if (tsreg->tssr & TS_SC) { /* Special Condition; Error */ log (TS_PRI, "%s: tssr 0x%x, state %d\n", sc->sc_dev.dv_xname, tsreg->tssr, sc->sc_state); tsinit (sc); return (-1); } /* XXX */ } /* * Check if command is an ioctl or not (ie. read or write). * If it's an ioctl then just set the flags for later use; * For other commands attempt to setup a buffer pointer. */ if (bp == &ts_cbuf[ctlr]) { ioctl = 1; } else { ioctl = 0; /* * now we try to map the buffer into uba map space (???) */ i = TS_UBAFLAGS; switch (vax_cputype) { case VAX_8600: case VAX_780: i |= UBA_CANTWAIT; break; case VAX_750: i |= sc->sc_unit.uu_ubinfo | UBA_CANTWAIT; break; case VAX_730: case VAX_78032: i |= UBA_CANTWAIT; break; default: printf ("unsupported cpu %d in tsstart.\n", vax_cputype); } /* end switch (vax_cputype) */ if ((i = ubasetup(sc->sc_dev.dv_parent->dv_unit, bp, i)) == 0) { /* * For some reasons which I don't (yet? :) understand, * tmscp.c initiates in this situation a GET-UNIT * command. (Because no data-buffers are neccess. ??) */ cmd = TS_CMD_STAT; goto do_cmd; return (-1); /* ??? */ } #if defined(VAX750) if (vax_cputype == VAX_750) itmp = i & 0xfffffff; /* mask off bdp */ else #endif itmp = i; /* XXX */ } /* * If it's an ioctl command, then assemble the command. * The "b_resid" field holds the command-number as defined * in */ if (ioctl) { switch ((int)bp->b_resid) { case MTWEOF: cmd = TS_CMD_WTM; break; case MTFSF: cmd = TS_CMD_STMF; tscmdp->cw1 = bp->b_bcount; break; case MTBSF: cmd = TS_CMD_STMR; tscmdp->cw1 = bp->b_bcount; break; case MTFSR: cmd = TS_CMD_SRF; tscmdp->cw1 = bp->b_bcount; break; case MTBSR: cmd = TS_CMD_SRR; tscmdp->cw1 = bp->b_bcount; break; case MTREW: cmd = TS_CMD_RWND; #ifndef TS11_COMPAT if (bp->b_bcount == 0) { cmd = TS_CMD_RWII; } #endif break; case MTOFFL: cmd = TS_CMD_RWUL; break; case MTNOP: cmd = TS_CMD_STAT; break; default: printf ("%s: bad ioctl %d\n", sc->sc_dev.dv_xname, (int)bp->b_resid); /* Need a no-op. get status */ cmd = TS_CMD_STAT; } /* end switch (bp->b_resid) */ } else { /* Its a read/write command (not an ioctl) */ tscmdp->cw1 = UBAI_ADDR(i) & 0xffff; tscmdp->cw2 = (UBAI_ADDR(i) >> 16) & 0x3f; tscmdp->cw3 = bp->b_bcount; if (bp->b_flags & B_READ) { cmd = TS_CMD_RNF; } else { cmd = TS_CMD_WD; } bp->b_ubinfo = itmp; /* save mapping info */ } /* * Move buffer to I/O wait pseudo-queue */ if (ts_wtab[ctlr]) { /* * we are already waiting for something ... * this should not happen, so we have a problem now. * bertram: set error-flag and call iodone() ??? */ } ts_wtab[ctlr] = bp; /* * Now that the command-buffer is setup, give it to the controller */ do_cmd: return (tsexec(ctlr, cmd)); } /* * initialize the controller by sending WRITE CHARACTERISTICS command. * contents of command- and message-buffer are assembled during this * function. */ int tswchar (ctlr) int ctlr; { struct ts_softc *sc = ts_cd.cd_devs[ctlr]; volatile struct tsdevice *tsregs = ts[ctlr].reg; volatile struct tscmd *tscmdp = &ts[ctlr].cmd; volatile struct tsmsg *tsmsgp = &ts[ctlr].msg; volatile unsigned int sr, ma, timeout; /* * assemble and send "WRITE CHARACTERISTICS" command */ ma = (long)tsmsgp; if (ma & 0x7FC00001) { /* address must be even and 22-bit */ printf ("invalid address 0x%0x for msg-buffer.\n", ma); return (-1); } tsmsgp->hdr = ma & 0xFFFF; /* low order addr. bits */ tsmsgp->dfl = (ma >> 16) & 0x003F; /* high order addr. bits */ tsmsgp->rbpcr = 16; /* size of message-buffer */ tsmsgp->xst0 = 0; /* chacacteristics mode word */ tsmsgp->xst1 = 0; /* control word (ext.feat.) */ #ifdef TS11_COMPAT tsmsgp->rbpcr = 14; /* size of message-buffer */ tsmsgp->xst0 = 0; /* chacacteristics mode word */ tsmsgp->xst1 = 0; /* control word (ext.feat.) */ #else tsmsgp->rbpcr = 16; /* size of extended message buffer */ tsmsgp->xst0 = 0; /* chacacteristics mode word */ tsmsgp->xst1 = 0; /* unit-select */ tsmsgp->xst1 |= TS_WC_HSP; /* high speed */ #endif #ifdef ENABLE_ESS tsmsgp->xst0 |= TS_WC_ESS; #ifdef ENABLE_ENB tsmsgp->xst0 |= TS_WC_ENB; #endif #endif #ifdef ENABLE_EAI tsmsgp->xst0 |= TS_WC_EAI; #ifdef ENABLE_ERI tsmsgp->xst0 |= TS_WC_ERI; #endif #endif tscmdp->cmdr = TS_CF_ACK | TS_CF_IE | TS_CMD_WCHAR; /* obsolete */ tscmdp->cw1 = ma & 0xFFFF; tscmdp->cw2 = (ma >> 16) & 0x003F; tscmdp->cw3 = 10; /* size of charact.-data */ if (tsexec (ctlr, TS_CMD_WCHAR) < 0) { printf ("%s: write characteristics command failed [%x]\n", sc->sc_dev.dv_xname, tsregs->tssr); return (-1); } timeout = 1000; /* timeout in 10 seconds */ do { DELAY(10000); sr = tsregs->tssr; debug10 (("\ttssr: 0x%x\n", sr)); if (timeout-- > 0) { printf ("timeout during initialize."); tsstatus (sr); return (-1); } } while ((sr & TS_SSR) == 0); tsstatus (sr); return (0); } /* * */ void tsreset(ctlr) int ctlr; { struct ts_softc *sc = ts_cd.cd_devs[ctlr]; volatile struct tsdevice *tsreg = ts[ctlr].reg; volatile unsigned int sr, timeout; /* * reset ctlr by writing into TSSR, then write characteristics */ timeout = 1000; /* timeout in 10 seconds */ tsreg->tssr = 0; /* start initialization */ do { DELAY(10000); sr = tsreg->tssr; debug10 (("\ttssr: 0x%x\n", sr)); if (timeout-- > 0) { if (sr != 0) printf ("%s: timeout waiting for TS_SSR\n", sc->sc_dev.dv_xname); tsstatus (sr); return; } } while ((sr & TS_SSR) == 0); /* wait until subsystem ready */ tsstatus (sr); return; } /* * probe for device. If found, try to raise an interrupt. * XXX - most of this should be done in the attach routine. */ int tsmatch(parent, match, aux) struct device *parent; void *match, *aux; { struct ts_softc *sc = match; struct uba_softc *uh = (void *)parent; struct uba_attach_args *ua = aux; struct tsdevice *tsregs = (struct tsdevice*)ua->ua_addr; volatile unsigned int sr, timeout, count; int ctlr = sc->sc_dev.dv_unit; ts_wtab[ctlr] = NULL; sc->sc_ts = &ts[ctlr]; sc->sc_state = ST_PROBE; sc->sc_flags = 0; ts[ctlr].reg = (struct tsdevice*)ua->ua_addr; /* * Set host-settable interrupt vector. * Assign 0 to the TSSR register to start the ts-device initialization. * The device is not really initialized at this point, this is just to * find out if the device exists. */ sc->sc_ivec = (uh->uh_lastiv -= 4); count = 0; again: timeout = 1000; /* timeout in 10 seconds */ tsregs->tssr = 0; /* start initialization */ do { DELAY(10000); sr = tsregs->tssr; debug10 (("\ttssr-1: 0x%x\n", sr)); if (timeout-- > 0) { if (sr != 0) /* the device exists !!! */ printf ("%s: timeout waiting for TS_SSR\n", sc->sc_dev.dv_xname); tsstatus (sr); goto bad; } } while ((sr & TS_SSR) == 0); /* wait until subsystem ready */ tsstatus (sr); tswchar (ctlr); /* write charact. to enable interrupts */ /* completion of this will raise the intr. */ #ifdef notyet sc->sc_ipl = br = qbgetpri(); #else sc->sc_ipl = 0x15; #endif return (sizeof (struct tsdevice)); bad: if (++count < 3) goto again; #ifdef notyet splx(s); #endif return (0); } /* * Try to find a slave (a drive) on the controller. * Since there's only one drive per controller there's nothing to do. * (we could check the status of the drive (online/offline/...) */ void tsattach(parent, self, aux) struct device *parent, *self; void *aux; { struct ts_softc *sc = (void *)self; int ctlr = sc->sc_dev.dv_unit; struct tsmsg *tsmsgp = &ts[ctlr].msg; trace (("tsslave (%x, %x)\n", ui, reg)); /* * write the characteristics (again) * This will raise an interrupt during ST_SLAVE which indicates * completion of initialization ... */ sc->sc_state = ST_SLAVE; /* tsintr() checks this ... */ if (tswchar (ctlr) < 0) { printf ("%s: cannot initialize", sc->sc_dev.dv_xname); } sc->sc_micro = (tsmsgp->xst2 & TS_SF_MCRL) >> 2; printf ("%s: rev %d, extended features %s, transport %s\n", sc->sc_dev.dv_xname, sc->sc_micro, (tsmsgp->xst2 & TS_SF_EFES ? "enabled" : "disabled"), (ts[ctlr].reg->tssr & TS_OFL ? "offline" : "online")); tsinit (sc); /* must be called once, why not here ? */ } /* * TSV05/TS05 interrupt routine */ void tsintr(ctlr) int ctlr; { register struct ts_softc *sc = ts_cd.cd_devs[ctlr]; register struct tsmsg *tsmsgp = &ts[ctlr].msg; register struct tscmd *tscmdp = &ts[ctlr].cmd; volatile struct tsdevice *tsreg = ts[ctlr].reg; struct uba_unit *um = &sc->sc_unit; register struct buf *bp; unsigned short sr = tsreg->tssr; /* save TSSR */ unsigned short mh = tsmsgp->hdr; /* and msg-header */ /* clear the message header ??? */ short ccode = tscmdp->cmdr & TS_CF_CCODE; short cmask = tscmdp->cmdr & TS_CF_CMASK; #ifdef DEBUG { char bits[64]; printf ("TSSR: %s, MSG: %x ", bitmask_snprintf(sr, TS_TSSR_BITS, bits, sizeof(bits)), mh); } switch (tsmsgp->hdr & 0x001F) { case 16: printf ("(End)"); break; case 17: printf ("(Fail)"); break; case 18: printf ("(Error)"); break; case 19: printf ("(Attention)"); break; } #endif trace ((" tsintr (%d, %d, %d, %x)\n", uba, vector, level, ctlr)); if (tsmsgp->xst0 & TS_SF_VCK) sc->sc_cmdf |= TS_CF_CVC; #ifdef QBA /* copied from uda.c */ if(vax_cputype == VAX_78032) splx(sc->sc_ipl); /* Qbus interrupt protocol is odd */ #endif /* * There are two different things which can (and should) be checked: * the actual (internal) state and the device's result (tssr/msg.hdr) * * For each state there's only one "normal" interrupt. Anything else * has to be checked more intensively. Thus in a first run according * to the internal state the expected interrupt is checked/handled. * * In a second run the remaining (not yet handled) interrupts are * checked according to the drive's result. */ switch (sc->sc_state) { case ST_INVALID: /* * Ignore unsolicited interrupts. */ log (LOG_WARNING, "%s: stray intr [%x,%x]\n", sc->sc_dev.dv_xname, sr, mh); return; case ST_SLAVE: /* * this interrupt was caused by write-charact. command * issued by tsslave() and indicates the end of the * initialization phase. Just ignore it ... */ if ((sr & TS_SC) != 0 || (sr & TS_TC) != TS_TC_NORM) { printf("%s: problem during init [%x,%x]\n", sc->sc_dev.dv_xname, sr, mh); /* return here ??? */ /* break and check the error outside switch ??? */ break; } sc->sc_state = ST_RUNNING; return; case ST_RUNNING: /* * Here we expect interrupts indicating the end of * commands or indicating problems. */ /* * Anything else is handled outside this switch ... */ break; case ST_IDLE: break; default: printf ("%s: unexpected interrupt during state %d [%x,%x]\n", sc->sc_dev.dv_xname, sc->sc_state, sr, mh); return; } /* * now we check the termination class. */ switch (sr & TS_TC) { case TS_TC_NORM: /* * Normal termination -- The operation is completed * witout incident. */ sc->sc_state = ST_IDLE; /* XXX ??? */ sc->sc_state = ST_RUNNING; sc->sc_liowf = (ccode == TS_CC_WRITE); sc->sc_rtc = 0; if ((bp = ts_wtab[ctlr]) != NULL) { ts_wtab[ctlr] = NULL; /* pseudo-unlink */ if (bp != &ts_cbuf[ctlr]) { /* no ioctl */ ubarelse((struct uba_softc *) sc->sc_dev.dv_parent, (int *)&bp->b_ubinfo); #if defined(VAX750) if (vax_cputype == VAX_750 && sc->sc_unit.uu_ubinfo != 0) ubarelse((struct uba_softc *) sc->sc_dev.dv_parent, &sc->sc_unit.uu_ubinfo); /* XXX */ #endif } bp->b_resid = tsmsgp->rbpcr; debug (("tsintr: iodone(NORM) [%d,%d,%d]\n", bp->b_resid, bp->b_bcount, tsmsgp->rbpcr)); iodone (bp); /* bertram: ioctl ??? */ } return; case TS_TC_ATTN: /* * Attention condition -- this code indicates that the * drive has undergone a status change, such as going * off-line or coming on-line. * (Without EAI enabled, no Attention interrupts occur. * drive status changes are signaled by the VCK flag.) */ return; case TS_TC_TSA: /* * Tape Status Alert -- A status condition is encountered * that may have significance to the program. Bits of * interest in the extended status registers include * TMK, EOT and RLL. */ debug (("Tape Status Alert\n")); tsxstatus (tsmsgp); if (tsmsgp->xst0 & TS_SF_TMK) { debug (("Tape Mark detected")); } if (tsmsgp->xst0 & TS_SF_EOT) { debug (("End of Tape")); } break; case TS_TC_FR: /* * Function Reject -- The specified function was not * initiated. Bits of interest include OFL, VCK, BOT, * WLE, ILC and ILA. */ debug (("Function reject\n")); tsxstatus (tsmsgp); if (sr & TS_OFL) { printf ("tape is off-line.\n"); break; } if (tsmsgp->xst0 & TS_SF_VCK) { printf ("Volume check: repeating command ...\n"); tsexec (ctlr, tscmdp->cmdr); return; } if (tsmsgp->xst0 & TS_SF_BOT) { printf ("bottom of tape.\n"); } if (tsmsgp->xst0 & TS_SF_WLE) { printf ("Write Lock Error\n"); } break; case TS_TC_TPD: /* * Recoverable Error -- Tape position is a record beyond * what its position was when the function was initiated. * Suggested recovery procedure is to log the error and * issue the appropriate retry command. */ debug (("Tape position down\n")); switch (cmask) { case TS_CMD_RNF: /* Read Next (forward) */ debug (("retry read forward ...\n")); sc->sc_rtc = 1; tsexec (ctlr, TS_CMD_RPF); return; case TS_CMD_RPR: /* Read Previous (Reverse) */ debug (("retry read reverse ...\n")); sc->sc_rtc = 1; tsexec (ctlr, TS_CMD_RNR); return; case TS_CMD_WD: /* Write Data (Next) */ debug (("retry write data ...\n")); sc->sc_rtc = 1; tsexec (ctlr, TS_CMD_WDR); return; case TS_CMD_WTM: debug (("retry write tape mark ...\n")); sc->sc_rtc = 1; tsexec (ctlr, TS_CMD_WTMR); return; default: debug (("TPD in command %x\n", cmask)); } break; case TS_TC_TNM: /* * Recoverable Error -- Tape position has not changed. * Suggested recovery procedure is to log the error and * reissue the original command. */ printf ("Tape not moved\n"); if (sc->sc_rtc < 3) { sc->sc_rtc++; /* bertram: log the error !!! */ printf ("retrying command %x (%d)\n", tscmdp->cmdr, sc->sc_rtc); tsexec (ctlr, tscmdp->cmdr); return; } break; case TS_TC_TPL: /* * Unrecoverable Error -- Tape position has been lost. * No valid recovery procedures exist unless the tape * has labels or sequence numbers. */ printf ("Tape position lost\n"); break; case TS_TC_FCE: /* * Fatal subsytem Error -- The subsytem is incapable * of properly performing commands, or at least its * integrity is seriously questionable. Refer to the * fatal class code field in the TSSR register for * additional information on the type of fatal error. */ printf ("Fatal Controller Error\n"); default: printf ("%s: error 0x%x, resetting controller\n", sc->sc_dev.dv_xname, sr & TS_TC); tsreset (ctlr); } /* * reset controller ?? call tsinit() ??? */ if ((bp = ts_wtab[ctlr]) != NULL) { ts_wtab[ctlr] = NULL; /* pseudo unlink */ if (bp != &ts_cbuf[ctlr]) /* no ioctl */ ubarelse((struct uba_softc *)sc->sc_dev.dv_parent, (int *)&bp->b_ubinfo); if ((sr & TS_TC) != TS_TC_NORM) bp->b_flags |= B_ERROR; debug (("resid:%d, count:%d, rbpcr:%d\n", bp->b_resid, bp->b_bcount, tsmsgp->rbpcr)); bp->b_resid = tsmsgp->rbpcr; /* XXX */ debug (("tsintr: iodone(%x)\n", bp->b_flags)); iodone (bp); } if ((sr & TS_TC) > TS_TC_FR) tsreset (ctlr); return; } /* * Open a ts device and set the unit online. If the controller is not * in the run state, call init to initialize the ts controller first. */ int tsopen (dev, flag, type, p) dev_t dev; int flag, type; struct proc *p; { register struct uba_device *ui; register struct uba_ctlr *um; register struct ts_softc *sc; register int unit = TS_UNIT(dev); int s; trace (("tsopen (%x, %x)\n", dev, flag)); if (unit >= ts_cd.cd_ndevs) return ENXIO; sc = ts_cd.cd_devs[unit]; if (sc == 0) return ENXIO; if (sc->sc_openf) return EBUSY; sc->sc_openf = 1; s = splbio (); if (sc->sc_state < ST_RUNNING) { /* XXX */ printf ("%s not running.\n", sc->sc_dev.dv_xname); (void) splx (s); sc->sc_openf = 0; return (ENXIO); } (void) splx (s); /* * check if transport is really online. * (without attention-interrupts enabled, we really don't know * the actual state of the transport. Thus we call get-status * (ie. MTNOP) once and check the actual status.) */ tscommand (dev, MTNOP, 1); if (ts[unit].reg->tssr & TS_OFL) { printf ("%s: transport is offline.\n", sc->sc_dev.dv_xname); sc->sc_openf = 0; return EIO; /* transport is offline */ } sc->sc_liowf = 0; return 0; } /* * Close tape device. * * If tape was open for writing or last operation was * a write, then write two EOF's and backspace over the last one. * Unless this is a non-rewinding special file, rewind the tape. * * Make the tape available to others, by clearing openf flag. */ int tsclose (dev, flag, type, p) dev_t dev; int flag, type; struct proc *p; { register struct ts_softc *sc = ts_cd.cd_devs[TS_UNIT(dev)]; if (flag == FWRITE || ((flag & FWRITE) && sc->sc_liowf)) { /* * We are writing two tape marks (EOT), but place the tape * before the second one, so that another write operation * will overwrite the second one and leave and EOF-mark. */ tscommand (dev, MTWEOF, 1); /* Write Tape Mark */ tscommand (dev, MTWEOF, 1); /* Write Tape Mark */ tscommand (dev, MTBSF, 1); /* Skip Tape Marks Reverse */ } if ((dev & T_NOREWIND) == 0) tscommand (dev, MTREW, 0); sc->sc_openf = 0; sc->sc_liowf = 0; return 0; } /* * Manage buffers and perform block mode read and write operations. */ void tsstrategy (bp) register struct buf *bp; { register int unit = TS_UNIT(bp->b_dev); struct ts_softc *sc = (void *)ts_cd.cd_devs[unit]; int s; s = splbio (); /* * we have only one command at one time, no credits. * thus we don't need buffer management and controller queue * just try to execute the command ... */ tsstart (sc, bp); splx(s); return; } /* * Catch ioctl commands, and call the "command" routine to do them. */ int tsioctl (dev, cmd, data, flag, p) dev_t dev; u_long cmd; caddr_t data; int flag; struct proc *p; { register struct buf *bp = &ts_cbuf[TS_UNIT(dev)]; register struct ts_softc *sc; register struct mtop *mtop; /* mag tape cmd op to perform */ register struct mtget *mtget; /* mag tape struct to get info in */ register callcount; /* number of times to call routine */ int scount; /* number of files/records to space */ int spaceop = 0; /* flag for skip/space operation */ int error = 0; trace (("tsioctl (%x, %x, %x, %d)\n", dev, cmd, data, flag)); switch (cmd) { case MTIOCTOP: /* do a mag tape op */ mtop = (struct mtop *)data; switch (mtop->mt_op) { case MTWEOF: /* write an end-of-file record */ callcount = mtop->mt_count; scount = 1; break; case MTFSF: /* forward space file */ case MTBSF: /* backward space file */ case MTFSR: /* forward space record */ case MTBSR: /* backward space record */ spaceop = 1; callcount = 1; scount = mtop->mt_count; break; case MTREW: /* rewind */ case MTOFFL: /* rewind and put the drive offline */ case MTNOP: /* no operation, sets status only */ callcount = 1; scount = 1; /* wait for this rewind */ break; case MTRETEN: /* retension */ case MTERASE: /* erase entire tape */ case MTEOM: /* forward to end of media */ case MTNBSF: /* backward space to begin of file */ case MTCACHE: /* enable controller cache */ case MTNOCACHE: /* disable controller cache */ case MTSETBSIZ: /* set block size; 0 for variable */ case MTSETDNSTY: /* set density code for current mode */ debug (("ioctl %d not implemented.\n", mtop->mt_op)); return (ENXIO); default: debug (("invalid ioctl %d\n", mtop->mt_op)); return (ENXIO); } /* switch (mtop->mt_op) */ if (callcount <= 0 || scount <= 0) { debug (("invalid values %d/%d\n", callcount, scount)); return (EINVAL); } do { tscommand (dev, mtop->mt_op, scount); if (spaceop && bp->b_resid) { debug (("spaceop didn't complete\n")); return (EIO); } if (bp->b_flags & B_ERROR) { debug (("error in ioctl %d\n", mtop->mt_op)); break; } } while (--callcount > 0); if (bp->b_flags & B_ERROR) if ((error = bp->b_error) == 0) return (EIO); return (error); case MTIOCGET: /* get tape status */ sc = ts_cd.cd_devs[TS_UNIT(dev)]; mtget = (struct mtget *)data; mtget->mt_type = MT_ISTS; mtget->mt_dsreg = (unsigned)(ts[TS_UNIT(dev)].reg->tssr); mtget->mt_erreg = (unsigned)(ts[TS_UNIT(dev)].msg.hdr); mtget->mt_resid = 0; /* ??? */ mtget->mt_density = 0; /* ??? */ break; case MTIOCIEOT: /* ignore EOT error */ debug (("MTIOCIEOT not implemented.\n")); return (ENXIO); case MTIOCEEOT: /* enable EOT error */ debug (("MTIOCEEOT not implemented.\n")); return (ENXIO); default: debug (("invalid ioctl cmd 0x%x\n", cmd)); return (ENXIO); } return (0); } /* * */ int tsread (dev, uio) dev_t dev; struct uio *uio; { return (physio (tsstrategy, NULL, dev, B_READ, minphys, uio)); } /* * */ int tswrite (dev, uio) dev_t dev; struct uio *uio; { return (physio (tsstrategy, NULL, dev, B_WRITE, minphys, uio)); } /* * */ int tsdump(dev, blkno, va, size) dev_t dev; daddr_t blkno; caddr_t va; size_t size; { trace (("tsdump (%x)\n", dev)); return 0; } /*----------------------------------------------------------------------*/ int tsstatus (sr) int sr; { #ifdef DEBUG char bits[64]; debug (("status: TSSR=%s\n", bitmask_snprintf(sr, TS_TSSR_BITS, bits, sizeof(bits)))); if (tsdebug < 5) return (0); if (sr & TS_SC) printf ("special condition\n"); if (sr & TS_UPE) printf ("UPE\n"); if (sr & TS_SCE) printf ("Sanity Check Error\n"); if (sr & TS_RMR) printf ("Register Modification Refused\n"); if (sr & TS_NXM) printf ("Nonexistent Memory\n"); if (sr & TS_NBA) printf ("Need Buffer Address\n"); if (sr & TS_A11) printf ("Address Bits 17-16\n"); if (sr & TS_SSR) printf ("Subsystem Ready\n"); if (sr & TS_OFL) printf ("Off Line\n"); if (sr & TS_FTC) printf ("Fatal Termination Class Code\n"); switch (sr & TS_TC) { case TS_TC_NORM: printf ("Normal Termination\n"); break; case TS_TC_ATTN: printf ("Attention Condition\n"); break; case TS_TC_TSA: printf ("Tape status \n"); break; case TS_TC_FR: printf ("Function reject\n"); break; case TS_TC_TPD: printf ("Tape position down\n"); break; case TS_TC_TNM: printf ("Tape not moved\n"); break; case TS_TC_TPL: printf ("Tape position lost\n"); break; case TS_TC_FCE: printf ("Fatal Controller Error\n"); break; } #endif return (0); } void tsxstatus (mp) struct tsmsg *mp; { #ifdef DEBUG char bits[64]; debug (("tsxstatus: xst0=%s, ", bitmask_snprintf(mp->xst0, TS_XST0_BITS, bits, sizeof(bits)))); debug (("xst1=%s, ", bitmask_snprintf(mp->xst1, TS_XST1_BITS, bits, sizeof(bits)))); debug (("xst2=%s, ", bitmask_snprintf(mp->xst2, TS_XST2_BITS, bits, sizeof(bits)))); debug (("xst3=%s, ", bitmask_snprintf(mp->xst3, TS_XST3_BITS, bits, sizeof(bits)))); debug (("xst4=%s\n", bitmask_snprintf(mp->xst4, "\20", bits, sizeof(bits)))); if (tsdebug < 10) return (0); if (mp->xst0 & TS_SF_TMK) printf ("Tape Mark Detected\n"); if (mp->xst0 & TS_SF_RLS) printf ("Record Length Short\n"); if (mp->xst0 & TS_SF_LET) printf ("Logical End of Tape\n"); if (mp->xst0 & TS_SF_RLL) printf ("Record Length Long\n"); if (mp->xst0 & TS_SF_WLE) printf ("Write Lock Error\n"); if (mp->xst0 & TS_SF_NEF) printf ("Nonexecutable Function\n"); if (mp->xst0 & TS_SF_ILC) printf ("Illegal Command\n"); if (mp->xst0 & TS_SF_ILA) printf ("Illegal Address\n"); if (mp->xst0 & TS_SF_MOT) printf ("Motion\n"); if (mp->xst0 & TS_SF_ONL) printf ("On-Line\n"); if (mp->xst0 & TS_SF_IE) printf ("Interrupt Enable\n"); if (mp->xst0 & TS_SF_VCK) printf ("Volume Check\n"); if (mp->xst0 & TS_SF_PED) printf ("Phase Encoded Drive\n"); if (mp->xst0 & TS_SF_WLK) printf ("Write Locked\n"); if (mp->xst0 & TS_SF_BOT) printf ("Beginning of Tape\n"); if (mp->xst0 & TS_SF_EOT) printf ("End of Tape\n"); if (mp->xst1 & TS_SF_DLT) printf ("Data Late\n"); if (mp->xst1 & TS_SF_COR) printf ("Correctable Data\n"); if (mp->xst1 & TS_SF_RBP) printf ("Read Bus Parity Error\n"); if (mp->xst1 & TS_SF_UNC) printf ("Uncorrectable Data or Hard Error\n"); if (mp->xst2 & TS_SF_OPM) printf ("Operation in Progress\n"); if (mp->xst2 & TS_SF_RCE) printf ("RAM Checksum Error\n"); if (mp->xst2 & TS_SF_WCF) printf ("Write Clock Failure\n"); if (mp->xst2 & TS_SF_EFES) printf ("extended features enabled\n"); if (mp->xst2 & TS_SF_BES) printf ("Buffering enabled\n"); printf ("micro-code revision level: %d\n", (mp->xst2 & TS_SF_MCRL)>>2); printf ("unit number: %d\n", (mp->xst2 & TS_SF_UNIT)); if (mp->xst3 & TS_SF_MDE) printf ("Micro-Diagnostics Error Code: 0x%x\n", mp->xst3 >> 8); if (mp->xst3 & TS_SF_OPI) printf ("Operation Incomplete\n"); if (mp->xst3 & TS_SF_REV) printf ("Revers\n"); if (mp->xst3 & TS_SF_DCK) printf ("Density Check\n"); if (mp->xst3 & TS_SF_RIB) printf ("Reverse into BOT\n"); if (mp->xst4 & TS_SF_HSP) printf ("High Speed\n"); if (mp->xst4 & TS_SF_RCX) printf ("Retry Count Exceeded\n"); #endif }