/* $OpenBSD: hdc9224.h,v 1.2 1997/05/29 00:05:33 niklas Exp $ */ /* $NetBSD: hdc9224.h,v 1.1 1996/07/20 18:55:12 ragge Exp $ */ /* * Copyright (c) 1996 Ludd, University of Lule}, Sweden. * All rights reserved. * * This code is derived from software contributed to Ludd by Bertram Barth. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. All advertising materials mentioning features or use of this software * must display the following acknowledgement: * This product includes software developed at Ludd, University of * Lule}, Sweden and its contributors. * 4. The name of the author may not be used to endorse or promote products * derived from this software without specific prior written permission * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. */ struct hdc9224_DKCreg { unsigned char dkc_reg; /* Disk Register Data Access Port (rw)*/ unsigned char fill[3]; /* bytes are longword aligned */ unsigned char dkc_cmd; /* Disk Controller Command Port (wo) */ #define dkc_stat dkc_cmd /* Interrupt Status Port (ro) */ }; /* * definition of some commands (constant bits only, incomplete!) */ #define DKC_CMD_RESET 0x00 /* terminate non-data-transfer cmds */ #define DKC_CMD_DRDESELECT 0x01 /* done when no drive is in use */ #define DKC_CMD_SETREGPTR 0x40 /* logically or-ed with reg-number */ #define DKC_CMD_DRSELECT 0x20 #define DKC_CMD_DRSEL_HDD 0x24 /* select HDD, or-ed with unit-numb. */ #define DKC_CMD_DRSEL_RX33 0x28 /* or-ed with unit-number of RX33 */ #define DKC_CMD_DRSEL_RX50 0x2C /* or-ed with unit-number of RX50 */ #define DKC_CMD_RESTORE 0x02 #define DKC_CMD_STEP 0x04 #define DKC_CMD_STEPIN_FDD 0x04 /* one step inward for floppy */ #define DKC_CMD_STEPOUT_FDD 0x06 /* one step outward (toward cyl #0) */ #define DKC_CMD_POLLDRIVE 0x10 #define DKC_CMD_SEEKREADID 0x50 #define DKC_CMD_FORMATTRACK 0x60 #define DKC_CMD_READTRACK 0x5A #define DKC_CMD_READPHYSICAL 0x58 #define DKC_CMD_READLOGICAL 0x5C #define DKC_CMD_READ_HDD 0x5D /* read-logical, bypass=0, xfer=1 */ #define DKC_CMD_READ_RX33 0x5D /* ??? */ #define DKC_CMD_WRITEPHYSICAL 0x80 #define DKC_CMD_WRITELOGICAL 0xC0 #define DKC_CMD_WRITE_HDD 0xA0 /* bypass=0, ddmark=0 */ #define DKC_CMD_WRITE_RX33 0xA1 /* precompensation differs... */ #define DKC_CMD_WRITE_RX50 0xA4 /* * Definition of bits in the DKC_STAT register */ #define DKC_ST_INTPEND (1<<7) /* interrupt pending */ #define DKC_ST_DMAREQ (1<<6) /* DMA request */ #define DKC_ST_DONE (1<<5) /* command done */ #define DKC_ST_TERMCOD (3<<3) /* termination code (see below) */ #define DKC_ST_RDYCHNG (1<<2) /* ready change */ #define DKC_ST_OVRUN (1<<1) /* overrun/underrun */ #define DKC_ST_BADSECT (1<<0) /* bad sector */ /* * Definition of the termination codes */ #define DKC_TC_SUCCESS (0<<3) /* Successful completion */ #define DKC_TC_RDIDERR (1<<3) /* Error in READ-ID sequence */ #define DKC_TC_VRFYERR (2<<3) /* Error in VERIFY sequence */ #define DKC_TC_DATAERR (3<<3) /* Error in DATA-TRANSFER seq. */ /* * Definitions of delays neccessary for floppy-operation */ #define DKC_DELAY_MOTOR 500 /* allow 500 ms to reach speed */ #define DKC_DELAY_SELECT 70 /* 70 ms for data-recovery-circuit */ #define DKC_DELAY_POSITION 59 /* 59 ms for RX33, 100 ms for RX50 */ #define DKC_DELAY_HEADSET 18 /* 18 ms when changing head-number */ /* * The HDC9224 has 11/15(?) internal registers which are accessible via * the Disk-Register-Data-Access-Port DKC_REG */ struct hdc9224_UDCreg { /* internal disk controller registers */ u_char udc_dma7; /* 0: DMA adress bits 0 - 7 */ u_char udc_dma15; /* 1: DMA adress bits 8 - 15 */ u_char udc_dma23; /* 2: DMA adress bits 16 - 23 */ u_char udc_dsect; /* 3: desired/starting sector number */ #define udc_csect udc_dsect /* current sector number */ u_char udc_dhead; /* 4: cyl-bits 8-10, desired head number */ #define udc_chead udc_dhead /* current head number */ u_char udc_dcyl; /* 5: desired cylinder number */ #define udc_ccyl udc_dcyl /* current cylinder number */ u_char udc_scnt; /* 6: sector count register */ u_char udc_rtcnt; /* 7: retry count register */ u_char udc_mode; /* 8: operation mode/chip status */ #define udc_cstat udc_mode /* chip status register */ u_char udc_term; /* 9: termination conditions/drive status */ #define udc_dstat udc_term /* drive status register */ u_char udc_data; /* 10: data */ }; /* * Definition of bits in the Current-Head register */ #define UDC_CH_BADSECT (1<<7) /* indicates a bad sector (if bypass=0) */ #define UDC_CH_CYLBITS (0x70) /* bits 10-8 of current cylinder number */ #define UDC_CH_HEADNO (0x0F) /* current head number */ /* * Definition of bits in the Retry-Count register */ #define UDC_RC_RTRYCNT (0xF0) /* 1's compl. in read-log, 0 all others */ #define UDC_RC_RXDISAB (1<<3) /* must/should be 0 for normal operation */ #define UDC_RC_INVRDY (1<<2) /* polarity of floppy-status, important! */ #define UDC_RC_MOTOR (1<<1) /* turn on floppy-motor, no effect on HDD */ #define UDC_RC_LOSPEED (1<<0) /* floppy-speed select, RX33: 0, RX50: 1 */ #define UDC_RC_HDD_READ 0xF2 /* 0x72 ??? */ #define UDC_RC_HDD_WRT 0xF2 /* 0xF0 ??? */ #define UDC_RC_RX33READ 0x76 /* enable retries when reading floppies */ #define UDC_RC_RX33WRT 0xF6 #define UDC_RC_RX50READ 0x77 /* enable retries when reading floppies */ #define UDC_RC_RX50WRT 0xF7 /* * Definition of bits in the Operating-Mode register */ #define UDC_MD_HDMODE (1<<7) /* must be 1 for all FDD and HDD */ #define UDC_MD_CHKCOD (3<<5) /* error-check: FDD/CRC: 0, HDD/ECC: 1 */ #define UDC_MD_DENS (1<<4) /* density select, must be 0 */ #define UDC_MD_UNUSED (1<<3) /* bit 3 is not used and must be 0 */ #define UDC_MD_SRATE (7<<0) /* seek step rate */ #define UDC_MD_HDD 0xC0 #define UDC_MD_RX33 0x82 #define UDC_MD_RX50 0x81 /* * Definition of bits in the Chip-Status register */ #define UDC_CS_RETREQ (1<<7) /* retry required */ #define UDC_CS_ECCATT (1<<6) /* error correction attempted */ #define UDC_CS_ECCERR (1<<5) /* ECC/CRC error */ #define UDC_CS_DELDATA (1<<4) /* deleted data mark */ #define UDC_CS_SYNCERR (1<<3) /* synchronization error */ #define UDC_CS_COMPERR (1<<2) /* compare error */ #define UDC_CS_PRESDRV (0x3) /* present drive selected */ /* * Definition of bits in the Termination-Conditions register */ #define UDC_TC_CRCPRE (1<<7) /* CRC register preset, must be 1 */ #define UDC_TC_UNUSED (1<<6) /* bit 6 is not used and must be 0 */ #define UDC_TC_INTDONE (1<<5) /* interrupt on done */ #define UDC_TC_TDELDAT (1<<4) /* terminate on deleted data */ #define UDC_TC_TDSTAT3 (1<<3) /* terminate on drive status 3 change */ #define UDC_TC_TWPROT (1<<2) /* terminate on write-protect (FDD only) */ #define UDC_TC_INTRDCH (1<<1) /* interrupt on ready change (FDD only) */ #define UDC_TC_TWRFLT (1<<0) /* interrupt on write-fault (HDD only) */ #define UDC_TC_HDD 0xA5 /* 0xB5 ??? */ #define UDC_TC_FDD 0xA0 /* 0xAA ??? 0xB4 ??? */ /* * Definition of bits in the Disk-Status register */ #define UDC_DS_SELACK (1<<7) /* select acknowledge (harddisk only!) */ #define UDC_DS_INDEX (1<<6) /* index point */ #define UDC_DS_SKCOM (1<<5) /* seek complete */ #define UDC_DS_TRK00 (1<<4) /* track 0 */ #define UDC_DS_DSTAT3 (1<<3) /* drive status 3 (MBZ) */ #define UDC_DS_WRPROT (1<<2) /* write protect (floppy only!) */ #define UDC_DS_READY (1<<1) /* drive ready bit */ #define UDC_DS_WRFAULT (1<<0) /* write fault */