/* $OpenBSD: ncr.c,v 1.24 2008/07/30 18:08:04 miod Exp $ */ /* $NetBSD: ncr.c,v 1.32 2000/06/25 16:00:43 ragge Exp $ */ /*- * Copyright (c) 1996 The NetBSD Foundation, Inc. * All rights reserved. * * This code is derived from software contributed to The NetBSD Foundation * by Adam Glass, David Jones, Gordon W. Ross, and Jens A. Nilsson. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. */ /* * This file contains the machine-dependent parts of the NCR-5380 * controller. The machine-independent parts are in ncr5380sbc.c. * * Jens A. Nilsson. * * Credits: * * This code is based on arch/sun3/dev/si* * Written by David Jones, Gordon Ross, and Adam Glass. */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #define MIN_DMA_LEN 128 struct si_dma_handle { int dh_flags; #define SIDH_BUSY 1 #define SIDH_OUT 2 caddr_t dh_addr; int dh_len; struct proc *dh_proc; }; struct si_softc { struct ncr5380_softc ncr_sc; struct evcount ncr_intrcnt; int ncr_cvec; caddr_t ncr_addr; int ncr_off; int ncr_dmaaddr; int ncr_dmacount; int ncr_dmadir; /* Pointers to bus_space */ bus_space_tag_t sc_regt; bus_space_handle_t sc_regh; struct si_dma_handle ncr_dma[SCI_OPENINGS]; struct vsbus_dma sc_vd; int onlyscsi; /* This machine needs no queueing */ }; static int ncr_dmasize; static int si_match(struct device *, void *, void *); static void si_attach(struct device *, struct device *, void *); static void si_minphys(struct buf *); static void si_dma_alloc(struct ncr5380_softc *); static void si_dma_free(struct ncr5380_softc *); static void si_dma_setup(struct ncr5380_softc *); static void si_dma_start(struct ncr5380_softc *); static void si_dma_poll(struct ncr5380_softc *); static void si_dma_stop(struct ncr5380_softc *); static void si_dma_go(void *); #define NCR5380_READ(sc, reg) bus_space_read_1(sc->sc_regt, \ 0, sc->ncr_sc.reg) #define NCR5380_WRITE(sc, reg, val) bus_space_write_1(sc->sc_regt, \ 0, sc->ncr_sc.reg, val) struct scsi_adapter si_ops = { ncr5380_scsi_cmd, /* scsi_cmd() */ si_minphys, /* scsi_minphys() */ NULL, /* probe_dev() */ NULL /* free_dev() */ }; struct scsi_device si_dev = { NULL, /* use default error handler */ NULL, /* no start function */ NULL, /* no async handler */ NULL /* use default done routine */ }; struct cfattach ncr_ca = { sizeof(struct si_softc), si_match, si_attach }; struct cfdriver ncr_cd = { NULL, "ncr", DV_DULL }; static int si_match(parent, cf, aux) struct device *parent; void *cf; void *aux; { struct vsbus_attach_args *va = aux; volatile char *si_csr = (char *) va->va_addr; if (vax_boardtype == VAX_BTYP_49 || vax_boardtype == VAX_BTYP_46 || vax_boardtype == VAX_BTYP_48 || vax_boardtype == VAX_BTYP_1303) return 0; /* This is the way Linux autoprobes the interrupt MK-990321 */ si_csr[12] = 0; si_csr[16] = 0x80; si_csr[0] = 0x80; si_csr[4] = 5; /* 0xcf */ DELAY(100000); return 1; } static void si_attach(parent, self, aux) struct device *parent, *self; void *aux; { struct vsbus_attach_args *va = aux; struct si_softc *sc = (struct si_softc *) self; struct ncr5380_softc *ncr_sc = &sc->ncr_sc; struct scsibus_attach_args saa; int tweak, target; printf("\n"); /* enable interrupts on vsbus too */ scb_vecalloc(va->va_cvec, (void (*)(void *)) ncr5380_intr, sc, SCB_ISTACK, &sc->ncr_intrcnt); sc->ncr_cvec = va->va_cvec; evcount_attach(&sc->ncr_intrcnt, self->dv_xname, (void *)&sc->ncr_cvec, &evcount_intr); /* * DMA area mapin. * On VS3100, split the 128K block between the two devices. * On VS2000, don't care for now. */ #define DMASIZE (64*1024) if (va->va_paddr & 0x100) { /* Secondary SCSI controller */ sc->ncr_off = DMASIZE; sc->onlyscsi = 1; } sc->ncr_addr = (caddr_t)va->va_dmaaddr; ncr_dmasize = min(va->va_dmasize, MAXPHYS); /* * MD function pointers used by the MI code. */ ncr_sc->sc_dma_alloc = si_dma_alloc; ncr_sc->sc_dma_free = si_dma_free; ncr_sc->sc_dma_setup = si_dma_setup; ncr_sc->sc_dma_start = si_dma_start; ncr_sc->sc_dma_poll = si_dma_poll; ncr_sc->sc_dma_stop = si_dma_stop; /* DMA control register offsets */ sc->ncr_dmaaddr = 32; /* DMA address in buffer, longword */ sc->ncr_dmacount = 64; /* DMA count register */ sc->ncr_dmadir = 68; /* Direction of DMA transfer */ ncr_sc->sc_pio_out = ncr5380_pio_out; ncr_sc->sc_pio_in = ncr5380_pio_in; ncr_sc->sc_min_dma_len = MIN_DMA_LEN; /* * Initialize fields used by the MI code. */ /* sc->sc_regt = Unused on VAX */ sc->sc_regh = vax_map_physmem(va->va_paddr, 1); /* Register offsets */ ncr_sc->sci_r0 = (void *)sc->sc_regh+0; ncr_sc->sci_r1 = (void *)sc->sc_regh+4; ncr_sc->sci_r2 = (void *)sc->sc_regh+8; ncr_sc->sci_r3 = (void *)sc->sc_regh+12; ncr_sc->sci_r4 = (void *)sc->sc_regh+16; ncr_sc->sci_r5 = (void *)sc->sc_regh+20; ncr_sc->sci_r6 = (void *)sc->sc_regh+24; ncr_sc->sci_r7 = (void *)sc->sc_regh+28; ncr_sc->sc_no_disconnect = 0xff; /* * Get the SCSI chip target address out of NVRAM. * This do not apply to the VS2000. */ tweak = clk_tweak + (va->va_paddr & 0x100 ? 3 : 0); if (vax_boardtype == VAX_BTYP_410) target = 7; else target = (clk_page[0xbc/2] >> tweak) & 7; ncr_sc->sc_link.adapter_softc = sc; ncr_sc->sc_link.adapter_target = target; ncr_sc->sc_link.adapter = &si_ops; ncr_sc->sc_link.device = &si_dev; ncr_sc->sc_link.openings = 4; /* * Init the vsbus DMA resource queue struct */ sc->sc_vd.vd_go = si_dma_go; sc->sc_vd.vd_arg = sc; bzero(&saa, sizeof(saa)); saa.saa_sc_link = &(ncr_sc->sc_link); /* * Initialize si board itself. */ ncr5380_init(ncr_sc); ncr5380_reset_scsibus(ncr_sc); DELAY(2000000); config_found(&(ncr_sc->sc_dev), &saa, scsiprint); } /* * Adjust the max transfer size. The DMA buffer is only 16k on VS2000. */ static void si_minphys(bp) struct buf *bp; { if (bp->b_bcount > ncr_dmasize) bp->b_bcount = ncr_dmasize; } void si_dma_alloc(ncr_sc) struct ncr5380_softc *ncr_sc; { struct si_softc *sc = (struct si_softc *)ncr_sc; struct sci_req *sr = ncr_sc->sc_current; struct scsi_xfer *xs = sr->sr_xs; struct si_dma_handle *dh; struct buf *bp; int xlen, i; #ifdef DIAGNOSTIC if (sr->sr_dma_hand != NULL) panic("si_dma_alloc: already have DMA handle"); #endif /* Polled transfers shouldn't allocate a DMA handle. */ if (sr->sr_flags & SR_IMMED) return; xlen = ncr_sc->sc_datalen; /* Make sure our caller checked sc_min_dma_len. */ if (xlen < MIN_DMA_LEN) panic("si_dma_alloc: len=0x%x", xlen); /* * Find free PDMA handle. Guaranteed to find one since we * have as many PDMA handles as the driver has processes. * (instances?) */ for (i = 0; i < SCI_OPENINGS; i++) { if ((sc->ncr_dma[i].dh_flags & SIDH_BUSY) == 0) goto found; } panic("ncr: no free PDMA handles"); found: dh = &sc->ncr_dma[i]; dh->dh_flags = SIDH_BUSY; dh->dh_addr = ncr_sc->sc_dataptr; dh->dh_len = xlen; bp = xs->bp; if (bp != NULL) dh->dh_proc = (bp->b_flags & B_PHYS ? bp->b_proc : NULL); else dh->dh_proc = NULL; /* Remember dest buffer parameters */ if (xs->flags & SCSI_DATA_OUT) dh->dh_flags |= SIDH_OUT; sr->sr_dma_hand = dh; } void si_dma_free(ncr_sc) struct ncr5380_softc *ncr_sc; { struct sci_req *sr = ncr_sc->sc_current; struct si_dma_handle *dh = sr->sr_dma_hand; #ifdef DIAGNOSTIC if (dh == NULL) panic("si_dma_free: no DMA handle"); #endif if (ncr_sc->sc_state & NCR_DOINGDMA) panic("si_dma_free: free while DMA in progress"); if (dh->dh_flags & SIDH_BUSY) dh->dh_flags = 0; else printf("si_dma_free: free'ing unused buffer\n"); sr->sr_dma_hand = NULL; } void si_dma_setup(ncr_sc) struct ncr5380_softc *ncr_sc; { /* Do nothing here */ } void si_dma_start(ncr_sc) struct ncr5380_softc *ncr_sc; { struct si_softc *sc = (struct si_softc *)ncr_sc; /* Just put on queue; will call go() from below */ if (sc->onlyscsi) si_dma_go(ncr_sc); else vsbus_dma_start(&sc->sc_vd); } /* * go() routine called when another transfer somewhere is finished. */ void si_dma_go(arg) void *arg; { struct ncr5380_softc *ncr_sc = arg; struct si_softc *sc = (struct si_softc *)ncr_sc; struct sci_req *sr = ncr_sc->sc_current; struct si_dma_handle *dh = sr->sr_dma_hand; /* * Set the VAX-DMA-specific registers, and copy the data if * it is directed "outbound". */ if (dh->dh_flags & SIDH_OUT) { vsbus_copyfromproc(dh->dh_proc, dh->dh_addr, sc->ncr_addr + sc->ncr_off, dh->dh_len); bus_space_write_1(sc->sc_regt, sc->sc_regh, sc->ncr_dmadir, 0); } else { bus_space_write_1(sc->sc_regt, sc->sc_regh, sc->ncr_dmadir, 1); } bus_space_write_4(sc->sc_regt, sc->sc_regh, sc->ncr_dmacount, -dh->dh_len); bus_space_write_4(sc->sc_regt, sc->sc_regh, sc->ncr_dmaaddr, sc->ncr_off); /* * Now from the 5380-internal DMA registers. */ if (dh->dh_flags & SIDH_OUT) { NCR5380_WRITE(sc, sci_tcmd, PHASE_DATA_OUT); NCR5380_WRITE(sc, sci_icmd, SCI_ICMD_DATA); NCR5380_WRITE(sc, sci_mode, NCR5380_READ(sc, sci_mode) | SCI_MODE_DMA | SCI_MODE_DMA_IE); NCR5380_WRITE(sc, sci_dma_send, 0); } else { NCR5380_WRITE(sc, sci_tcmd, PHASE_DATA_IN); NCR5380_WRITE(sc, sci_icmd, 0); NCR5380_WRITE(sc, sci_mode, NCR5380_READ(sc, sci_mode) | SCI_MODE_DMA | SCI_MODE_DMA_IE); NCR5380_WRITE(sc, sci_irecv, 0); } ncr_sc->sc_state |= NCR_DOINGDMA; } /* * When? */ void si_dma_poll(ncr_sc) struct ncr5380_softc *ncr_sc; { printf("si_dma_poll\n"); } void si_dma_stop(ncr_sc) struct ncr5380_softc *ncr_sc; { struct si_softc *sc = (struct si_softc *)ncr_sc; struct sci_req *sr = ncr_sc->sc_current; struct si_dma_handle *dh = sr->sr_dma_hand; int count, i; if (ncr_sc->sc_state & NCR_DOINGDMA) ncr_sc->sc_state &= ~NCR_DOINGDMA; /* * Sometimes the FIFO buffer isn't drained when the * interrupt is posted. Just loop here and hope that * it will drain soon. */ for (i = 0; i < 20000; i++) { count = bus_space_read_4(sc->sc_regt, sc->sc_regh, sc->ncr_dmacount); if (count == 0) break; DELAY(100); } if (count == 0) { if (((dh->dh_flags & SIDH_OUT) == 0)) { vsbus_copytoproc(dh->dh_proc, sc->ncr_addr + sc->ncr_off, dh->dh_addr, dh->dh_len); } ncr_sc->sc_dataptr += dh->dh_len; ncr_sc->sc_datalen -= dh->dh_len; } NCR5380_WRITE(sc, sci_mode, NCR5380_READ(sc, sci_mode) & ~(SCI_MODE_DMA | SCI_MODE_DMA_IE)); NCR5380_WRITE(sc, sci_icmd, 0); if (sc->onlyscsi == 0) vsbus_dma_intr(); /* Try to start more transfers */ }