/* $OpenBSD: hilreg.h,v 1.4 2003/06/02 23:28:01 millert Exp $ */ /* $NetBSD: hilreg.h,v 1.6 1997/02/02 09:39:21 thorpej Exp $ */ /* * Copyright (c) 1988 University of Utah. * Copyright (c) 1990, 1993 * The Regents of the University of California. All rights reserved. * * This code is derived from software contributed to Berkeley by * the Systems Programming Group of the University of Utah Computer * Science Department. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. Neither the name of the University nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * * from: Utah $Hdr: hilreg.h 1.10 92/01/21$ * * @(#)hilreg.h 8.1 (Berkeley) 6/10/93 */ #include #define HIL_BUSY 0x02 #define HIL_DATA_RDY 0x01 /* HIL status bits */ #define HIL_POLLDATA 0x10 /* HIL poll data follows */ #define HIL_COMMAND 0x08 /* Start of original command */ #define HIL_ERROR 0x80 /* HIL error */ #define HIL_RECONFIG 0x80 /* HIL has reconfigured */ #define HIL_SSHIFT 4 /* Bits to shift status over */ #define HIL_SMASK 0x0f /* Service request status mask */ #define HIL_DEVMASK 0x07 /* HIL status types */ #define HIL_68K 0x04 /* Data from the 68k is ready */ #define HIL_STATUS 0x05 /* HIL status in data register */ #define HIL_DATA 0x06 /* HIL data in data register */ #define HIL_CTRLSHIFT 0x08 /* key + CTRL + SHIFT */ #define HIL_CTRL 0x09 /* key + CTRL */ #define HIL_SHIFT 0x0a /* key + SHIFT */ #define HIL_KEY 0x0b /* key only */ /* HIL commands */ #define HIL_IDENTIFY 0x03 /* Get device information */ #define HIL_READTIME 0x13 /* Read real time register */ #define HIL_RNAME 0x30 /* Report name */ #define HIL_RSTATUS 0x31 /* Report status */ #define HIL_DESCRIBE 0x32 /* Extended describe */ #define HIL_SECURITY 0x33 /* Read security bits */ #define HIL_DKR 0x3d /* Disable auto repeat */ #define HIL_ER1 0x3e /* Enable auto repeat 1/30 */ #define HIL_ER2 0x3f /* Enable auto repeat 1/60 */ #define HIL_PROMPT1 0x40 /* Prompt #1 */ #define HIL_PROMPT2 0x41 /* Prompt #2 */ #define HIL_PROMPT3 0x42 /* Prompt #3 */ #define HIL_PROMPT4 0x43 /* Prompt #4 */ #define HIL_PROMPT5 0x44 /* Prompt #5 */ #define HIL_PROMPT6 0x45 /* Prompt #6 */ #define HIL_PROMPT7 0x46 /* Prompt #7 */ #define HIL_PROMPT 0x47 /* Prompt */ #define HIL_ACK1 0x48 /* Acknowledge #1 */ #define HIL_ACK2 0x49 /* Acknowledge #2 */ #define HIL_ACK3 0x4a /* Acknowledge #3 */ #define HIL_ACK4 0x4b /* Acknowledge #4 */ #define HIL_ACK5 0x4c /* Acknowledge #5 */ #define HIL_ACK6 0x4d /* Acknowledge #6 */ #define HIL_ACK7 0x4e /* Acknowledge #7 */ #define HIL_ACK 0x4f /* Acknowledge */ #define HIL_INTON 0x5c /* Turn on interrupts. */ #define HIL_INTOFF 0x5d /* Turn off interrupts. */ #define HIL_SETARD 0xa0 /* Set auto-repeat delay */ #define HIL_SETARR 0xa2 /* Set auto-repeat rate */ #define HIL_SETTONE 0xa3 /* Set tone generator */ #define HIL_CNMT 0xb2 /* Clear nmi */ #define HIL_TRIGGER 0xc5 /* Trigger command */ #define HIL_STARTCMD 0xe0 /* Start loop command */ #define HIL_TIMEOUT 0xfe /* Timeout */ /* Read/write various registers on the 8042. */ #define HIL_READBUSY 0x02 /* internal "busy" register */ #define HIL_READKBDLANG 0x12 /* read keyboard language code */ #define HIL_WRITEKBDSADR 0xe9 #define HIL_WRITELPSTAT 0xea #define HIL_WRITELPCTRL 0xeb #define HIL_READKBDSADR 0xf9 #define HIL_READLPSTAT 0xfa #define HIL_READLPCTRL 0xfb /* BUSY bits */ #define BSY_LOOPBUSY 0x04 /* LPCTRL bits */ #define LPC_AUTOPOLL 0x01 /* enable auto-polling */ #define LPC_NOERROR 0x02 /* don't report errors */ #define LPC_NORECONF 0x04 /* don't report reconfigure */ #define LPC_KBDCOOK 0x10 /* cook all keyboards */ #define LPC_RECONF 0x80 /* reconfigure the loop */ /* LPSTAT bits */ #define LPS_DEVMASK 0x07 /* number of loop devices */ #define LPS_CONFGOOD 0x08 /* reconfiguration worked */ #define LPS_CONFFAIL 0x80 /* reconfiguration failed */ /* HIL packet headers */ #define HIL_MOUSEDATA 0x02 #define HIL_KBDDATA 0x40 #define HIL_MOUSEMOTION 0x02 /* mouse movement event */ #define HIL_TABLET 0x02 /* tablet motion event */ #define HIL_KNOBBOX 0x03 /* knob box motion data */ #define HIL_KBDBUTTON 0x40 /* keyboard button event */ #define HIL_MOUSEBUTTON 0x40 /* mouse button event */ #define HIL_BUTTONBOX 0x60 /* button box event */ /* ID module defines */ #define HILSCBIT 0x04 /* For setting auto repeat on the keyboard */ #define ar_format(x) ~((x - 10) / 10) #define KBD_ARD 400 /* initial delay in msec (10 - 2560) */ #define KBD_ARR 60 /* rate (10 - 2550 msec, 2551 == off) */ /* Device information bits */ #define HIL_ABSOLUTE 0x40 /* absolute positioning data */ #define HIL_16_BITS 0x20 /* 16 bit position accuracy */ #define HIL_IOB 0x10 /* I/O description byte follows */ #define HIL_AXMASK 0x03 /* Number of axes supported */ #define HILIOB_PROMPT 0x80 /* prompt and acknowledge (leds) supported */ #define HILIOB_PMASK 0x70 /* number of prompt & acknowledge supported */ #define HILIOB_PIO 0x08 /* proximity in/out (pressure) supported */ #define HILIOB_BMASK 0x07 /* number of buttons supported */