/* $OpenBSD: comreg.h,v 1.7 1997/10/15 14:04:18 pefo Exp $ */ /* $NetBSD: comreg.h,v 1.8 1996/02/05 23:01:50 scottr Exp $ */ /*- * Copyright (c) 1991 The Regents of the University of California. * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. All advertising materials mentioning features or use of this software * must display the following acknowledgement: * This product includes software developed by the University of * California, Berkeley and its contributors. * 4. Neither the name of the University nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * * @(#)comreg.h 7.2 (Berkeley) 5/9/91 */ #include #ifndef COM_FREQ /* allow to be set externally */ #define COM_FREQ 1843200 /* 16-bit baud rate divisor */ #endif #define COM_TOLERANCE 30 /* baud rate tolerance, in 0.1% units */ /* interrupt enable register */ #define IER_ERXRDY 0x1 /* Enable receiver interrupt */ #define IER_ETXRDY 0x2 /* Enable transmitter empty interrupt */ #define IER_ERLS 0x4 /* Enable line status interrupt */ #define IER_EMSC 0x8 /* Enable modem status interrupt */ /* interrupt identification register */ #define IIR_IMASK 0xf #define IIR_RXTOUT 0xc #define IIR_RLS 0x6 /* Line status change */ #define IIR_RXRDY 0x4 /* Receiver ready */ #define IIR_TXRDY 0x2 /* Transmitter ready */ #define IIR_MLSC 0x0 /* Modem status */ #define IIR_NOPEND 0x1 /* No pending interrupts */ #define IIR_FIFO_MASK 0xc0 /* set if FIFOs are enabled */ /* fifo control register */ #define FIFO_ENABLE 0x01 /* Turn the FIFO on */ #define FIFO_RCV_RST 0x02 /* Reset RX FIFO */ #define FIFO_XMT_RST 0x04 /* Reset TX FIFO */ #define FIFO_DMA_MODE 0x08 #define FIFO_TRIGGER_1 0x00 /* Trigger RXRDY intr on 1 character */ #define FIFO_TRIGGER_4 0x40 /* ibid 4 */ #define FIFO_TRIGGER_8 0x80 /* ibid 8 */ #define FIFO_TRIGGER_14 0xc0 /* ibid 14 */ /* line control register */ #define LCR_DLAB 0x80 /* Divisor latch access enable */ #define LCR_SBREAK 0x40 /* Break Control */ #define LCR_PZERO 0x38 /* Space parity */ #define LCR_PONE 0x28 /* Mark parity */ #define LCR_PEVEN 0x18 /* Even parity */ #define LCR_PODD 0x08 /* Odd parity */ #define LCR_PNONE 0x00 /* No parity */ #define LCR_PENAB 0x08 /* XXX - low order bit of all parity */ #define LCR_STOPB 0x04 /* 2 stop bits per serial word */ #define LCR_8BITS 0x03 /* 8 bits per serial word */ #define LCR_7BITS 0x02 /* 7 bits */ #define LCR_6BITS 0x01 /* 6 bits */ #define LCR_5BITS 0x00 /* 5 bits */ /* modem control register */ #define MCR_LOOPBACK 0x10 /* Loop test: echos from TX to RX */ #define MCR_IENABLE 0x08 /* Out2: enables UART interrupts */ #define MCR_DRS 0x04 /* Out1: resets some internal modems */ #define MCR_RTS 0x02 /* Request To Send */ #define MCR_DTR 0x01 /* Data Terminal Ready */ /* line status register */ #define LSR_RCV_FIFO 0x80 #define LSR_TSRE 0x40 /* Transmitter empty: byte sent */ #define LSR_TXRDY 0x20 /* Transmitter buffer empty */ #define LSR_BI 0x10 /* Break detected */ #define LSR_FE 0x08 /* Framing error: bad stop bit */ #define LSR_PE 0x04 /* Parity error */ #define LSR_OE 0x02 /* Overrun, lost incoming byte */ #define LSR_RXRDY 0x01 /* Byte ready in Receive Buffer */ #define LSR_RCV_MASK 0x1f /* Mask for incoming data or error */ /* modem status register */ /* All deltas are from the last read of the MSR. */ #define MSR_DCD 0x80 /* Current Data Carrier Detect */ #define MSR_RI 0x40 /* Current Ring Indicator */ #define MSR_DSR 0x20 /* Current Data Set Ready */ #define MSR_CTS 0x10 /* Current Clear to Send */ #define MSR_DDCD 0x08 /* DCD has changed state */ #define MSR_TERI 0x04 /* RI has toggled low to high */ #define MSR_DDSR 0x02 /* DSR has changed state */ #define MSR_DCTS 0x01 /* CTS has changed state */ #define COM_NPORTS 8 /* * WARNING: Serial console is assumed to be at COM1 address * and CONUNIT must be 0. */ #ifndef CONADDR #define CONADDR (0x3f8) #endif #ifndef CONUNIT #define CONUNIT (0) #endif