/* $NetBSD: elink3reg.h,v 1.3 1996/05/10 05:28:09 thorpej Exp $ */ /* * Copyright (c) 1995 Herb Peyerl * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. All advertising materials mentioning features or use of this software * must display the following acknowledgement: * This product includes software developed by Herb Peyerl. * 4. The name of Herb Peyerl may not be used to endorse or promote products * derived from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * */ /* * These define the EEPROM data structure. They are used in the probe * function to verify the existance of the adapter after having sent * the ID_Sequence. * * There are others but only the ones we use are defined here. */ #define EEPROM_NODE_ADDR_0 0x0 /* Word */ #define EEPROM_NODE_ADDR_1 0x1 /* Word */ #define EEPROM_NODE_ADDR_2 0x2 /* Word */ #define EEPROM_PROD_ID 0x3 /* 0x9[0-f]50 */ #define EEPROM_MFG_ID 0x7 /* 0x6d50 */ #define EEPROM_ADDR_CFG 0x8 /* Base addr */ #define EEPROM_RESOURCE_CFG 0x9 /* IRQ. Bits 12-15 */ /* * These are the registers for the 3Com 3c509 and their bit patterns when * applicable. They have been taken out the the "EtherLink III Parallel * Tasking EISA and ISA Technical Reference" "Beta Draft 10/30/92" manual * from 3com. */ #define EP_COMMAND 0x0e /* Write. BASE+0x0e is always a command reg. */ #define EP_STATUS 0x0e /* Read. BASE+0x0e is always status reg. */ #define EP_WINDOW 0x0f /* Read. BASE+0x0f is always window reg. */ /* * Window 0 registers. Setup. */ /* Write */ #define EP_W0_EEPROM_DATA 0x0c #define EP_W0_EEPROM_COMMAND 0x0a #define EP_W0_RESOURCE_CFG 0x08 #define EP_W0_ADDRESS_CFG 0x06 #define EP_W0_CONFIG_CTRL 0x04 /* Read */ #define EP_W0_PRODUCT_ID 0x02 #define EP_W0_MFG_ID 0x00 /* * Window 1 registers. Operating Set. */ /* Write */ #define EP_W1_TX_PIO_WR_2 0x02 #define EP_W1_TX_PIO_WR_1 0x00 /* Read */ #define EP_W1_FREE_TX 0x0c #define EP_W1_TX_STATUS 0x0b /* byte */ #define EP_W1_TIMER 0x0a /* byte */ #define EP_W1_RX_STATUS 0x08 #define EP_W1_RX_PIO_RD_2 0x02 #define EP_W1_RX_PIO_RD_1 0x00 /* * Window 2 registers. Station Address Setup/Read */ /* Read/Write */ #define EP_W2_RECVMASK_0 0x06 #define EP_W2_ADDR_5 0x05 #define EP_W2_ADDR_4 0x04 #define EP_W2_ADDR_3 0x03 #define EP_W2_ADDR_2 0x02 #define EP_W2_ADDR_1 0x01 #define EP_W2_ADDR_0 0x00 /* * Window 3 registers. FIFO Management. */ /* Read */ #define EP_W3_FREE_TX 0x0c #define EP_W3_FREE_RX 0x0a /* * Window 4 registers. Diagnostics. */ /* Read/Write */ #define EP_W4_MEDIA_TYPE 0x0a #define EP_W4_CTRLR_STATUS 0x08 #define EP_W4_NET_DIAG 0x06 #define EP_W4_FIFO_DIAG 0x04 #define EP_W4_HOST_DIAG 0x02 #define EP_W4_TX_DIAG 0x00 /* * Window 5 Registers. Results and Internal status. */ /* Read */ #define EP_W5_READ_0_MASK 0x0c #define EP_W5_INTR_MASK 0x0a #define EP_W5_RX_FILTER 0x08 #define EP_W5_RX_EARLY_THRESH 0x06 #define EP_W5_TX_AVAIL_THRESH 0x02 #define EP_W5_TX_START_THRESH 0x00 /* * Window 6 registers. Statistics. */ /* Read/Write */ #define TX_TOTAL_OK 0x0c #define RX_TOTAL_OK 0x0a #define TX_DEFERRALS 0x08 #define RX_FRAMES_OK 0x07 #define TX_FRAMES_OK 0x06 #define RX_OVERRUNS 0x05 #define TX_COLLISIONS 0x04 #define TX_AFTER_1_COLLISION 0x03 #define TX_AFTER_X_COLLISIONS 0x02 #define TX_NO_SQE 0x01 #define TX_CD_LOST 0x00 /* * Window 7 registers. * Address and length for a single bus-master DMA transfer. */ #define EP_W7_MASTER_ADDDRES 0x00 #define EP_W7_RX_ERROR 0x04 #define EP_W7_MASTER_LEN 0x06 #define EP_W7_RX_STATUS 0x08 #define EP_W7_TIMER 0x0a #define EP_W7_TX_STATUS 0x0b #define EP_W7_MASTER_STATUS 0x0c /* * Register definitions. */ /* * Command register. All windows. * * 16 bit register. * 15-11: 5-bit code for command to be executed. * 10-0: 11-bit arg if any. For commands with no args; * this can be set to anything. */ #define GLOBAL_RESET (u_short) 0x0000 /* Wait at least 1ms after issuing */ #define WINDOW_SELECT (u_short) (0x1<<11) #define START_TRANSCEIVER (u_short) (0x2<<11) /* Read ADDR_CFG reg to determine whether this is needed. If so; wait 800 uSec before using trans- ceiver. */ #define RX_DISABLE (u_short) (0x3<<11) /* state disabled on power-up */ #define RX_ENABLE (u_short) (0x4<<11) #define RX_RESET (u_short) (0x5<<11) #define RX_DISCARD_TOP_PACK (u_short) (0x8<<11) #define TX_ENABLE (u_short) (0x9<<11) #define TX_DISABLE (u_short) (0xa<<11) #define TX_RESET (u_short) (0xb<<11) #define REQ_INTR (u_short) (0xc<<11) /* * The following C_* acknowledge the various interrupts. * Some of them don't do anything. See the manual. */ #define ACK_INTR (u_short) (0x6800) # define C_INTR_LATCH (u_short) (ACK_INTR|0x01) # define C_CARD_FAILURE (u_short) (ACK_INTR|0x02) # define C_TX_COMPLETE (u_short) (ACK_INTR|0x04) # define C_TX_AVAIL (u_short) (ACK_INTR|0x08) # define C_RX_COMPLETE (u_short) (ACK_INTR|0x10) # define C_RX_EARLY (u_short) (ACK_INTR|0x20) # define C_INT_RQD (u_short) (ACK_INTR|0x40) # define C_UPD_STATS (u_short) (ACK_INTR|0x80) #define SET_INTR_MASK (u_short) (0x0e<<11) #define SET_RD_0_MASK (u_short) (0x0f<<11) #define SET_RX_FILTER (u_short) (0x10<<11) # define FIL_INDIVIDUAL (u_short) (0x01) # define FIL_MULTICAST (u_short) (0x02) # define FIL_BRDCST (u_short) (0x04) # define FIL_PROMISC (u_short) (0x08) #define SET_RX_EARLY_THRESH (u_short) (0x11<<11) #define SET_TX_AVAIL_THRESH (u_short) (0x12<<11) #define SET_TX_START_THRESH (u_short) (0x13<<11) #define STATS_ENABLE (u_short) (0x15<<11) #define STATS_DISABLE (u_short) (0x16<<11) #define STOP_TRANSCEIVER (u_short) (0x17<<11) /* * Status register. All windows. * * 15-13: Window number(0-7). * 12: Command_in_progress. * 11: reserved. * 10: reserved. * 9: reserved. * 8: reserved. * 7: Update Statistics. * 6: Interrupt Requested. * 5: RX Early. * 4: RX Complete. * 3: TX Available. * 2: TX Complete. * 1: Adapter Failure. * 0: Interrupt Latch. */ #define S_INTR_LATCH (u_short) (0x0001) #define S_CARD_FAILURE (u_short) (0x0002) #define S_TX_COMPLETE (u_short) (0x0004) #define S_TX_AVAIL (u_short) (0x0008) #define S_RX_COMPLETE (u_short) (0x0010) #define S_RX_EARLY (u_short) (0x0020) #define S_INT_RQD (u_short) (0x0040) #define S_UPD_STATS (u_short) (0x0080) #define S_COMMAND_IN_PROGRESS (u_short) (0x1000) /* * FIFO Registers. RX Status. * * 15: Incomplete or FIFO empty. * 14: 1: Error in RX Packet 0: Incomplete or no error. * 14-11: Type of error. [14-11] * 1000 = Overrun. * 1011 = Run Packet Error. * 1100 = Alignment Error. * 1101 = CRC Error. * 1001 = Oversize Packet Error (>1514 bytes) * 0010 = Dribble Bits. * (all other error codes, no errors.) * * 10-0: RX Bytes (0-1514) */ #define ERR_INCOMPLETE (u_short) (0x8000) #define ERR_RX (u_short) (0x4000) #define ERR_MASK (u_short) (0x7800) #define ERR_OVERRUN (u_short) (0x4000) #define ERR_RUNT (u_short) (0x5800) #define ERR_ALIGNMENT (u_short) (0x6000) #define ERR_CRC (u_short) (0x6800) #define ERR_OVERSIZE (u_short) (0x4800) #define ERR_DRIBBLE (u_short) (0x1000) /* * TX Status * * Reports the transmit status of a completed transmission. Writing this * register pops the transmit completion stack. * * Window 1/Port 0x0b. * * 7: Complete * 6: Interrupt on successful transmission requested. * 5: Jabber Error (TP Only, TX Reset required. ) * 4: Underrun (TX Reset required. ) * 3: Maximum Collisions. * 2: TX Status Overflow. * 1-0: Undefined. * */ #define TXS_COMPLETE 0x80 #define TXS_INTR_REQ 0x40 #define TXS_JABBER 0x20 #define TXS_UNDERRUN 0x10 #define TXS_MAX_COLLISION 0x08 #define TXS_STATUS_OVERFLOW 0x04 /* * FIFO Status (Window 4) * * Supports FIFO diagnostics * * Window 4/Port 0x04.1 * * 15: 1=RX receiving (RO). Set when a packet is being received * into the RX FIFO. * 14: Reserved * 13: 1=RX underrun (RO). Generates Adapter Failure interrupt. * Requires RX Reset or Global Reset command to recover. * It is generated when you read past the end of a packet - * reading past what has been received so far will give bad * data. * 12: 1=RX status overrun (RO). Set when there are already 8 * packets in the RX FIFO. While this bit is set, no additional * packets are received. Requires no action on the part of * the host. The condition is cleared once a packet has been * read out of the RX FIFO. * 11: 1=RX overrun (RO). Set when the RX FIFO is full (there * may not be an overrun packet yet). While this bit is set, * no additional packets will be received (some additional * bytes can still be pending between the wire and the RX * FIFO). Requires no action on the part of the host. The * condition is cleared once a few bytes have been read out * from the RX FIFO. * 10: 1=TX overrun (RO). Generates adapter failure interrupt. * Requires TX Reset or Global Reset command to recover. * Disables Transmitter. * 9-8: Unassigned. * 7-0: Built in self test bits for the RX and TX FIFO's. */ #define FIFOS_RX_RECEIVING (u_short) 0x8000 #define FIFOS_RX_UNDERRUN (u_short) 0x2000 #define FIFOS_RX_STATUS_OVERRUN (u_short) 0x1000 #define FIFOS_RX_OVERRUN (u_short) 0x0800 #define FIFOS_TX_OVERRUN (u_short) 0x0400 /* * Misc defines for various things. */ #define TAG_ADAPTER 0xd0 #define ACTIVATE_ADAPTER_TO_CONFIG 0xff #define ENABLE_DRQ_IRQ 0x0001 #define MFG_ID 0x506d /* `TCM' */ #define PROD_ID 0x5090 #define GO_WINDOW(x) bus_io_write_2(sc->sc_bc, \ sc->sc_ioh, EP_COMMAND, WINDOW_SELECT|x) #define AUI 0x1 #define BNC 0x2 #define UTP 0x4 #define IS_AUI (1<<13) #define IS_BNC (1<<12) #define IS_UTP (1<<9) #define EEPROM_BUSY (1<<15) #define EEPROM_TST_MODE (1<<14) #define READ_EEPROM (1<<7) #define ENABLE_UTP 0xc0 #define DISABLE_UTP 0x0 #define RX_BYTES_MASK (u_short) (0x07ff) #define IS_PCI_AUI (1<<5) #define IS_PCI_BNC (1<<4) #define IS_PCI_UTP (1<<3)