/* $OpenBSD: iha.h,v 1.10 2002/03/14 01:26:54 millert Exp $ */ /* * Initio INI-9xxxU/UW SCSI Device Driver * * Copyright (c) 2000-2001 Ken Westerback * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer, * without modification, immediately at the beginning of the file. * 2. The name of the author may not be used to endorse or promote products * derived from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. * IN NO EVENT SHALL THE AUTHOR OR HIS RELATIVES BE LIABLE FOR ANY DIRECT, * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF MIND, USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF * THE POSSIBILITY OF SUCH DAMAGE. * *------------------------------------------------------------------------- * * Ported from i91uscsi.h, provided by Initio Corporation, which probably * came from the same people who provided i91u.c: * * Device driver for the INI-9XXXU/UW or INIC-940/950 PCI SCSI Controller. * * FreeBSD * * Written for 386bsd and FreeBSD by * Winston Hung * * Copyright (c) 1997-99 Initio Corp. All rights reserved. * *------------------------------------------------------------------------- */ #define IHA_MAX_SG_ENTRIES 33 #define IHA_MAX_TARGETS 16 #define IHA_MAX_SCB 32 #define IHA_MAX_EXTENDED_MSG 4 /* SDTR(3) and WDTR(4) only */ /* * Scatter-Gather Element Structure */ struct iha_sg_element { u_int32_t SG_Ptr; /* Data Pointer */ u_int32_t SG_Len; /* Data Length */ }; /* * iha_scsi_req_q - SCSI Request structure used by the * Tulip (aka inic-940/950). Note that 32 * bit pointers and ints are assumed! */ struct iha_scsi_req_q { TAILQ_ENTRY(iha_scsi_req_q) SCB_ScbList; int SCB_Status; /* Current status of the SCB */ #define STATUS_QUEUED 0 /* SCB one of Free/Done/Pend */ #define STATUS_RENT 1 /* SCB allocated, not queued */ #define STATUS_SELECT 2 /* SCB being selected */ #define STATUS_BUSY 3 /* SCB I/O is active */ u_int8_t SCB_NxtStat; /* Next state function to apply */ u_int16_t SCB_SGIdx; /* Scatter/Gather Index */ u_int16_t SCB_SGMax; /* Scatter/Gather # valid entries */ int SCB_Flags; /* SCB Flags (xs->flags + private)*/ #define FLAG_RSENS 0x00010000 /* Request Sense sent */ #define FLAG_SG 0x00020000 /* Scatter/Gather used */ #define FLAG_DIR (SCSI_DATA_IN | SCSI_DATA_OUT) u_int8_t SCB_Target; /* Target Id */ u_int8_t SCB_Lun; /* Lun */ u_int32_t SCB_BufPAddr; /* Data Buffer Physical Addr */ u_int32_t SCB_BufLen; /* Data Allocation Length */ u_int8_t SCB_HaStat; /* Status of Host Adapter */ #define HOST_OK 0x00 /* OK - operation a success */ #define HOST_TIMED_OUT 0x01 /* Request timed out */ #define HOST_SPERR 0x10 /* SCSI parity error */ #define HOST_SEL_TOUT 0x11 /* Selection Timeout */ #define HOST_DO_DU 0x12 /* Data Over/Underrun */ #define HOST_BAD_PHAS 0x14 /* Unexpected SCSI bus phase */ #define HOST_SCSI_RST 0x1B /* SCSI bus was reset */ #define HOST_DEV_RST 0x1C /* Device was reset */ u_int8_t SCB_TaStat; /* SCSI Status Byte */ u_int8_t SCB_SGLen; /* # of valid entries in SGList */ u_int8_t SCB_SenseLen; /* Sense Data Allocation Length */ u_int8_t SCB_CDBLen; /* CDB Length */ u_int8_t SCB_Ident; /* Identity Message */ u_int8_t SCB_TagMsg; /* Tag Message */ u_int8_t SCB_TagId; /* Queue Tag */ u_int8_t SCB_CDB[12]; /* SCSI Command */ u_int32_t SCB_SGPAddr; /* SGList Physical Address */ u_int32_t SCB_SensePAddr; /* Sense Data PhysicalAddress */ struct scsi_xfer *SCB_Xs; /* xs this SCB is executing */ /* Start of SG list */ struct iha_sg_element SCB_SGList[IHA_MAX_SG_ENTRIES]; struct scsi_sense_data SCB_ScsiSenseData; bus_dmamap_t SCB_Dmamap;/* maps xs->buf xfer buffer */ int SCB_Timeout; /* in milliseconds */ struct tcs *SCB_Tcs; /* tcs for SCB_Target */ }; /* * Target Device Control Structure */ struct tcs { u_int16_t TCS_Flags; #define FLAG_SCSI_RATE 0x0007 /* Index into tul_rate_tbl[] */ #define FLAG_EN_DISC 0x0008 /* Enable disconnect */ #define FLAG_NO_SYNC 0x0010 /* No sync data transfer */ #define FLAG_NO_WIDE 0x0020 /* No wide data transfer */ #define FLAG_1GIGA 0x0040 /* 255 hd/63 sec (64/32) */ #define FLAG_SPINUP 0x0080 /* Start disk drive */ #define FLAG_WIDE_DONE 0x0100 /* WDTR msg has been sent */ #define FLAG_SYNC_DONE 0x0200 /* SDTR msg has been sent */ #define FLAG_NO_NEG_SYNC (FLAG_NO_SYNC | FLAG_SYNC_DONE) #define FLAG_NO_NEG_WIDE (FLAG_NO_WIDE | FLAG_WIDE_DONE) u_int8_t TCS_JS_Period; #define PERIOD_WIDE_SCSI 0x80 /* Enable Wide SCSI */ #define PERIOD_SYXPD 0x70 /* Synch. SCSI Xfer rate */ #define PERIOD_SYOFS 0x0f /* Synch. SCSI Offset */ u_int8_t TCS_SConfig0; u_int8_t TCS_TagCnt; struct iha_scsi_req_q *TCS_NonTagScb; }; struct iha_softc { struct device sc_dev; bus_space_tag_t sc_iot; bus_space_handle_t sc_ioh; bus_dma_tag_t sc_dmat; bus_dmamap_t sc_dmamap; struct scsi_link sc_link; struct scsi_adapter sc_adapter; void *sc_ih; /* * Initio specific fields */ u_int8_t HCS_Flags; #define FLAG_EXPECT_DISC 0x01 #define FLAG_EXPECT_SELECT 0x02 #define FLAG_EXPECT_RESET 0x10 #define FLAG_EXPECT_DONE_DISC 0x20 u_int8_t HCS_Semaph; #define SEMAPH_IN_MAIN 0x00 /* Already in tulip_main */ u_int8_t HCS_Phase; /* MSG C/D I/O */ #define PHASE_DATA_OUT 0x00 /* 0 0 0 */ #define PHASE_DATA_IN 0x01 /* 0 0 1 */ #define PHASE_CMD_OUT 0x02 /* 0 1 0 */ #define PHASE_STATUS_IN 0x03 /* 0 1 1 */ #define PHASE_MSG_OUT 0x06 /* 1 1 0 */ #define PHASE_MSG_IN 0x07 /* 1 1 1 */ u_int8_t HCS_JSInt; u_int8_t HCS_JSStatus0; u_int8_t HCS_JSStatus1; u_int8_t HCS_SConf1; u_int8_t HCS_Msg[IHA_MAX_EXTENDED_MSG]; /* [0] len, [1] Msg Code */ struct iha_scsi_req_q *HCS_Scb; /* SCB array */ struct iha_scsi_req_q *HCS_ActScb; /* SCB using SCSI bus */ TAILQ_HEAD(, iha_scsi_req_q) HCS_FreeScb, HCS_PendScb, HCS_DoneScb; struct tcs HCS_Tcs[IHA_MAX_TARGETS]; }; /* * EEPROM for one SCSI Channel * */ struct iha_nvram_scsi { u_int8_t NVM_SCSI_Id; /* 0x00 Channel Adapter SCSI Id */ u_int8_t NVM_SCSI_Cfg; /* 0x01 Channel configuration */ #define CFG_SCSI_RESET 0x0001 /* Reset bus at power up */ #define CFG_EN_PAR 0x0002 /* SCSI parity enable */ #define CFG_ACT_TERM1 0x0004 /* Enable active term 1 */ #define CFG_ACT_TERM2 0x0008 /* Enable active term 2 */ #define CFG_AUTO_TERM 0x0010 /* Enable auto terminator */ #define CFG_EN_PWR 0x0080 /* Enable power mgmt */ u_int8_t NVM_SCSI_CfgByte2; /* 0x02 Unused Channel Cfg byte 2*/ u_int8_t NVM_SCSI_Targets; /* 0x03 Number of SCSI targets */ /* 0x04 Lower bytes of targ flags*/ u_int8_t NVM_SCSI_TargetFlags[IHA_MAX_TARGETS]; }; /* * Tulip (aka ini-940/950) Serial EEPROM Layout * */ struct iha_nvram { /* ---------- Header ------------------------------------------------*/ u_int16_t NVM_Signature; /* 0x00 NVRAM Signature */ #define SIGNATURE 0xC925 u_int8_t NVM_Size; /* 0x02 Size of data structure*/ u_int8_t NVM_Revision; /* 0x03 Rev. of data structure*/ /* ---------- Host Adapter Structure --------------------------------*/ u_int8_t NVM_ModelByte0; /* 0x04 Model number (byte 0) */ u_int8_t NVM_ModelByte1; /* 0x05 Model number (byte 1) */ u_int8_t NVM_ModelInfo; /* 0x06 Model information */ u_int8_t NVM_NumOfCh; /* 0x07 Number of SCSI channel*/ u_int8_t NVM_BIOSConfig1; /* 0x08 BIOS configuration 1 */ #define BIOSCFG_ENABLE 0x01 /* BIOS enable */ #define BIOSCFG_8DRIVE 0x02 /* Support > 2 drives */ #define BIOSCFG_REMOVABLE 0x04 /* Support removable drv */ #define BIOSCFG_INT19 0x08 /* Intercept int 19h */ #define BIOSCFG_BIOSSCAN 0x10 /* Dynamic BIOS scan */ #define BIOSCFG_LUNSUPPORT 0x40 /* Support LUN */ #define BIOSCFG_DEFAULT (BIOSCFG_ENABLE) u_int8_t NVM_BIOSConfig2; /* 0x09 BIOS configuration 2 */ u_int8_t NVM_HAConfig1; /* 0x0a Host adapter config 1 */ #define HACFG_BOOTIDMASK 0x0F /* Boot ID number */ #define HACFG_LUNMASK 0x70 /* Boot LUN number */ #define HACFG_CHANMASK 0x80 /* Boot Channel number */ u_int8_t NVM_HAConfig2; /* 0x0b Host adapter config 2 */ struct iha_nvram_scsi NVM_Scsi[2]; /* 0x0c */ u_int8_t NVM_Reserved[10]; /* 0x34 */ /* --------- CheckSum -----------------------------------------------*/ u_int16_t NVM_CheckSum; /* 0x3E Checksum of NVRam */ }; /* * Tulip (aka inic-940/950) PCI Configuration Space Initio Specific Registers * * Offsets 0x00 through 0x3f are the standard PCI Configuration Header * registers. * * Offsets 0x40 through 0x4f, 0x51, 0x53, 0x57, 0x5b, 0x5e and 0x5f are * reserved registers. * * Registers 0x50 and 0x52 always read as 0. * * The register offset names and associated bit field names are taken * from the Inic-950 Data Sheet, Version 2.1, March 1997 */ #define TUL_GCTRL0 0x54 /* R/W Global Control 0 */ #define EEPRG 0x04 /* Enable EEPROM Programming */ #define TUL_GCTRL1 0x55 /* R/W Global Control 1 */ #define ATDEN 0x01 /* Auto Termination Detect Enable */ #define TUL_GSTAT 0x56 /* R/W Global Status - connector type */ #define TUL_EPAD0 0x58 /* R/W External EEPROM Addr (lo byte) */ #define TUL_EPAD1 0x59 /* R/W External EEPROM Addr (hi byte) */ #define TUL_PNVPG 0x5A /* R/W Data port to external BIOS */ #define TUL_EPDATA 0x5C /* R/W EEPROM Data port */ #define TUL_NVRAM 0x5D /* R/W Non-volatile RAM port */ #define READ 0x80 /* Read from given NVRAM addr */ #define WRITE 0x40 /* Write to given NVRAM addr */ #define ENABLE_ERASE 0x30 /* Enable NVRAM Erase/Write */ #define NVRCS 0x08 /* Select external NVRAM */ #define NVRCK 0x04 /* NVRAM Clock */ #define NVRDO 0x02 /* NVRAM Write Data */ #define NVRDI 0x01 /* NVRAM Read Data */ /* * Tulip (aka inic-940/950) SCSI Registers */ #define TUL_STCNT0 0x80 /* R/W 24 bit SCSI Xfer Count */ #define TCNT 0x00ffffff /* SCSI Xfer Transfer Count */ #define TUL_SFIFOCNT 0x83 /* R/W 5 bit FIFO counter */ #define FIFOC 0x1f /* SCSI Offset Fifo Count */ #define TUL_SISTAT 0x84 /* R Interrupt Register */ #define RSELED 0x80 /* Reselected */ #define STIMEO 0x40 /* Selected/Reselected Timeout */ #define SBSRV 0x20 /* SCSI Bus Service */ #define SRSTD 0x10 /* SCSI Reset Detected */ #define DISCD 0x08 /* Disconnected Status */ #define SELED 0x04 /* Select Interrupt */ #define SCAMSCT 0x02 /* SCAM selected */ #define SCMDN 0x01 /* Command Complete */ #define TUL_SIEN 0x84 /* W Interrupt enable */ #define ALL_INTERRUPTS 0xff #define TUL_STAT0 0x85 /* R Status 0 */ #define INTPD 0x80 /* Interrupt pending */ #define SQACT 0x40 /* Sequencer active */ #define XFCZ 0x20 /* Xfer counter zero */ #define SFEMP 0x10 /* FIFO empty */ #define SPERR 0x08 /* SCSI parity error */ #define PH_MASK 0x07 /* SCSI phase mask */ #define TUL_SCTRL0 0x85 /* W Control 0 */ #define RSSQC 0x20 /* Reset sequence counter */ #define RSFIFO 0x10 /* Flush FIFO */ #define CMDAB 0x04 /* Abort command (sequence) */ #define RSMOD 0x02 /* Reset SCSI Chip */ #define RSCSI 0x01 /* Reset SCSI Bus */ #define TUL_STAT1 0x86 /* R Status 1 */ #define STRCV 0x80 /* Status received */ #define MSGST 0x40 /* Message sent */ #define CPDNE 0x20 /* Data phase done */ #define DPHDN 0x10 /* Data phase done */ #define STSNT 0x08 /* Status sent */ #define SXCMP 0x04 /* Xfer completed */ #define SLCMP 0x02 /* Selection completed */ #define ARBCMP 0x01 /* Arbitration completed */ #define TUL_SCTRL1 0x86 /* W Control 1 */ #define ENSCAM 0x80 /* Enable SCAM */ #define NIDARB 0x40 /* No ID for Arbitration */ #define ENLRS 0x20 /* Low Level Reselect */ #define PWDN 0x10 /* Power down mode */ #define WCPU 0x08 /* Wide CPU */ #define EHRSL 0x04 /* Enable HW reselect */ #define ESBUSOUT 0x02 /* Enable SCSI data bus out latch */ #define ESBUSIN 0x01 /* Enable SCSI data bus in latch */ #define TUL_SSTATUS2 0x87 /* R Status 2 */ #define SABRT 0x80 /* Command aborted */ #define OSCZ 0x40 /* Offset counter zero */ #define SFFUL 0x20 /* FIFO full */ #define TMCZ 0x10 /* Timeout counter zero */ #define BSYGN 0x08 /* Busy release */ #define PHMIS 0x04 /* Phase mismatch */ #define SBEN 0x02 /* SCSI data bus enable */ #define SRST 0x01 /* SCSI bus reset in progress */ #define TUL_SCONFIG0 0x87 /* W Configuration */ #define PHLAT 0x80 /* Enable phase latch */ #define ITMOD 0x40 /* Initiator mode */ #define SPCHK 0x20 /* Enable SCSI parity */ #define ADMA8 0x10 /* Alternate dma 8-bits mode */ #define ADMAW 0x08 /* Alternate dma 16-bits mode */ #define EDACK 0x04 /* Enable DACK in wide SCSI xfer */ #define ALTPD 0x02 /* Alternate sync period mode */ #define DSRST 0x01 /* Disable SCSI Reset signal */ #define SCONFIG0DEFAULT (PHLAT | ITMOD | ALTPD | DSRST) #define TUL_SOFSC 0x88 /* R Offset */ #define TUL_SYNCM 0x88 /* W Sync. Xfer Period & Offset */ #define TUL_SBID 0x89 /* R SCSI BUS ID */ #define TUL_SID 0x89 /* W SCSI ID */ #define TUL_SALVC 0x8A /* R FIFO Avail Cnt/Identify Msg */ #define TUL_STIMO 0x8A /* W Sel/Resel Time Out Register */ #define TUL_SDATI 0x8B /* R SCSI Bus contents */ #define TUL_SDAT0 0x8B /* W SCSI Data Out */ #define TUL_SFIFO 0x8C /* R/W FIFO */ #define TUL_SSIGI 0x90 /* R SCSI signal in */ #define REQ 0x80 /* REQ signal */ #define ACK 0x40 /* ACK signal */ #define BSY 0x20 /* BSY signal */ #define SEL 0x10 /* SEL signal */ #define ATN 0x08 /* ATN signal */ #define MSG 0x04 /* MSG signal */ #define CD 0x02 /* C/D signal */ #define IO 0x01 /* I/O signal */ #define TUL_SSIGO 0x90 /* W SCSI signal out */ #define TUL_SCMD 0x91 /* R/W SCSI Command */ #define NO_OP 0x00 /* Place Holder for tulip_wait() */ #define SEL_NOATN 0x01 /* Select w/o ATN Sequence */ #define XF_FIFO_OUT 0x03 /* FIFO Xfer Infomation out */ #define MSG_ACCEPT 0x0F /* Message Accept */ #define SEL_ATN 0x11 /* Select w ATN Sequence */ #define SEL_ATNSTOP 0x12 /* Select w ATN & Stop Sequence */ #define SELATNSTOP 0x1E /* Select w ATN & Stop Sequence */ #define SEL_ATN3 0x31 /* Select w ATN3 Sequence */ #define XF_DMA_OUT 0x43 /* DMA Xfer Infomation out */ #define EN_RESEL 0x80 /* Enable Reselection */ #define XF_FIFO_IN 0x83 /* FIFO Xfer Infomation in */ #define CMD_COMP 0x84 /* Command Complete Sequence */ #define XF_DMA_IN 0xC3 /* DMA Xfer Infomation in */ #define TUL_STEST0 0x92 /* R/W Test0 */ #define TUL_STEST1 0x93 /* R/W Test1 */ /* * Tulip (aka inic-940/950) DMA Registers */ #define TUL_DXPA 0xC0 /* R/W DMA Xfer Physcl Addr 0-31*/ #define TUL_DXPAE 0xC4 /* R/W DMA Xfer Physcl Addr 32-63*/ #define TUL_DCXA 0xC8 /* R DMA Curr Xfer Physcl Addr 0-31*/ #define TUL_DCXAE 0xCC /* R DMA Curr Xfer Physcl Addr 32-63*/ #define TUL_DXC 0xD0 /* R/W DMA Xfer Counter */ #define TUL_DCXC 0xD4 /* R DMA Current Xfer Counter */ #define TUL_DCMD 0xD8 /* R/W DMA Command Register */ #define SGXFR 0x80 /* Scatter/Gather Xfer */ #define RSVD 0x40 /* Reserved - always reads as 0 */ #define XDIR 0x20 /* Xfer Direction 0/1 = out/in */ #define BMTST 0x10 /* Bus Master Test */ #define CLFIFO 0x08 /* Clear FIFO */ #define ABTXFR 0x04 /* Abort Xfer */ #define FRXFR 0x02 /* Force Xfer */ #define STRXFR 0x01 /* Start Xfer */ #define ST_X_IN (XDIR | STRXFR) #define ST_X_OUT ( STRXFR) #define ST_SG_IN (SGXFR | ST_X_IN) #define ST_SG_OUT (SGXFR | ST_X_OUT) #define TUL_ISTUS0 0xDC /* R/W Interrupt Status Register */ #define DGINT 0x80 /* DMA Global Interrupt */ #define RSVRD0 0x40 /* Reserved */ #define RSVRD1 0x20 /* Reserved */ #define SCMP 0x10 /* SCSI Complete */ #define PXERR 0x08 /* PCI Xfer Error */ #define DABT 0x04 /* DMA Xfer Aborted */ #define FXCMP 0x02 /* Forced Xfer Complete */ #define XCMP 0x01 /* Bus Master Xfer Complete */ #define TUL_ISTUS1 0xDD /* R DMA status Register */ #define SCBSY 0x08 /* SCSI Busy */ #define FFULL 0x04 /* FIFO Full */ #define FEMPT 0x02 /* FIFO Empty */ #define XPEND 0x01 /* Xfer pending */ #define TUL_IMSK 0xE0 /* R/W Interrupt Mask Register */ #define MSCMP 0x10 /* Mask SCSI Complete */ #define MPXFER 0x08 /* Mask PCI Xfer Error */ #define MDABT 0x04 /* Mask Bus Master Abort */ #define MFCMP 0x02 /* Mask Force Xfer Complete */ #define MXCMP 0x01 /* Mask Bus Master Xfer Complete */ #define MASK_ALL (MXCMP | MFCMP | MDABT | MPXFER | MSCMP) #define TUL_DCTRL0 0xE4 /* R/W DMA Control Register */ #define SXSTP 0x80 /* SCSI Xfer Stop */ #define RPMOD 0x40 /* Reset PCI Module */ #define RSVRD2 0x20 /* SCSI Xfer Stop */ #define PWDWN 0x10 /* Power Down */ #define ENTM 0x08 /* Enable SCSI Terminator Low */ #define ENTMW 0x04 /* Enable SCSI Terminator High */ #define DISAFC 0x02 /* Disable Auto Clear */ #define LEDCTL 0x01 /* LED Control */ #define TUL_DCTRL1 0xE5 /* R/W DMA Control Register 1 */ #define SDWS 0x01 /* SCSI DMA Wait State */ #define TUL_DFIFO 0xE8 /* R/W DMA FIFO */ #define TUL_WCTRL 0xF7 /* ?/? Bus master wait state control */ #define TUL_DCTRL 0xFB /* ?/? DMA delay control */ /* Functions used by higher SCSI layers, the kernel, or iha.c and iha_pci.c */ int iha_scsi_cmd(struct scsi_xfer *); int iha_intr(void *); void iha_minphys(struct buf *); int iha_init_tulip(struct iha_softc *);