/* $OpenBSD: wdcreg.h,v 1.10 2003/10/16 14:15:41 grange Exp $ */ /* $NetBSD: wdcreg.h,v 1.22 1999/03/07 14:02:54 bouyer Exp $ */ /*- * Copyright (c) 1991 The Regents of the University of California. * All rights reserved. * * This code is derived from software contributed to Berkeley by * William Jolitz. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. Neither the name of the University nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * * @(#)wdreg.h 7.1 (Berkeley) 5/9/91 */ /* * Controller register (wdr_ctlr) */ #define WDCTL_4BIT 0x08 /* use four head bits (wd1003) */ #define WDCTL_RST 0x04 /* reset the controller */ #define WDCTL_IDS 0x02 /* disable controller interrupts */ /* * Status bits. */ #define WDCS_BSY 0x80 /* busy */ #define WDCS_DRDY 0x40 /* drive ready */ #define WDCS_DWF 0x20 /* drive write fault */ #define WDCS_DSC 0x10 /* drive seek complete */ #define WDCS_DRQ 0x08 /* data request */ #define WDCS_CORR 0x04 /* corrected data */ #define WDCS_IDX 0x02 /* index */ #define WDCS_ERR 0x01 /* error */ #define WDCS_BITS "\020\010bsy\007drdy\006dwf\005dsc\004drq\003corr\002idx\001err" /* * Error bits. */ #define WDCE_BBK 0x80 /* bad block detected */ #define WDCE_CRC 0x80 /* CRC error (Ultra-DMA only) */ #define WDCE_UNC 0x40 /* uncorrectable data error */ #define WDCE_MC 0x20 /* media changed */ #define WDCE_IDNF 0x10 /* id not found */ #define WDCE_MCR 0x08 /* media change requested */ #define WDCE_ABRT 0x04 /* aborted command */ #define WDCE_TK0NF 0x02 /* track 0 not found */ #define WDCE_AMNF 0x01 /* address mark not found */ /* * Commands for Disk Controller. */ #define WDCC_NOP 0x00 /* NOP - Always fail with "aborted command" */ #define WDCC_RECAL 0x10 /* disk restore code -- resets cntlr */ #define WDCC_READ 0x20 /* disk read code */ #define WDCC_WRITE 0x30 /* disk write code */ #define WDCC__LONG 0x02 /* modifier -- access ecc bytes */ #define WDCC__NORETRY 0x01 /* modifier -- no retrys */ #define WDCC_FORMAT 0x50 /* disk format code */ #define WDCC_DIAGNOSE 0x90 /* controller diagnostic */ #define WDCC_IDP 0x91 /* initialize drive parameters */ #define WDCC_READMULTI 0xc4 /* read multiple */ #define WDCC_WRITEMULTI 0xc5 /* write multiple */ #define WDCC_SETMULTI 0xc6 /* set multiple mode */ #define WDCC_READDMA 0xc8 /* read with DMA */ #define WDCC_WRITEDMA 0xca /* write with DMA */ #define WDCC_ACKMC 0xdb /* acknowledge media change */ #define WDCC_LOCK 0xde /* lock drawer */ #define WDCC_UNLOCK 0xdf /* unlock drawer */ #define WDCC_FLUSHCACHE 0xe7 /* Flush cache */ #define WDCC_IDENTIFY 0xec /* read parameters from controller */ #define SET_FEATURES 0xef /* set features */ #define WDCC_IDLE 0xe3 /* set idle timer & enter idle mode */ #define WDCC_IDLE_IMMED 0xe1 /* enter idle mode */ #define WDCC_SLEEP 0xe6 /* enter sleep mode */ #define WDCC_STANDBY 0xe2 /* set standby timer & enter standby mode */ #define WDCC_STANDBY_IMMED 0xe0 /* enter standby mode */ #define WDCC_CHECK_PWR 0xe5 /* check power mode */ #define WDCC_READ_EXT 0x24 /* read 48-bit addressing */ #define WDCC_WRITE_EXT 0x34 /* write 48-bit addressing */ #define WDCC_READMULTI_EXT 0x29 /* read multiple 48-bit addressing */ #define WDCC_WRITEMULTI_EXT 0x39 /* write multiple 48-bit addressing */ #define WDCC_READDMA_EXT 0x25 /* read 48-bit addressing with DMA */ #define WDCC_WRITEDMA_EXT 0x35 /* write 48-bit addressing with DMA */ /* Subcommands for SET_FEATURES (features register ) */ #define WDSF_8BIT_PIO_EN 0x01 /* Enable 8bit PIO (CFA featureset) */ #define WDSF_EN_WR_CACHE 0x02 #define WDSF_SET_MODE 0x03 #define WDSF_REASSIGN_EN 0x04 /* Obsolete in ATA-6 */ #define WDSF_APM_EN 0x05 /* Enable Adv. Power Management */ #define WDSF_PUIS_EN 0x06 /* Enable Power-Up In Standby */ #define WDSF_PUIS_SPINUP 0x07 /* Power-Up In Standby spin-up */ #define WDSF_CFA_MODE1_EN 0x0A /* Enable CFA power mode 1 */ #define WDSF_RMSN_DS 0x31 /* Disable Removable Media Status */ #define WDSF_RETRY_DS 0x33 /* Obsolete in ATA-6 */ #define WDSF_AAM_EN 0x42 /* Enable Autom. Acoustic Management */ #define WDSF_SET_CACHE_SGMT 0x54 /* Obsolete in ATA-6 */ #define WDSF_READAHEAD_DS 0x55 /* Disable read look-ahead */ #define WDSF_RLSE_EN 0x5D /* Enable release interrupt */ #define WDSF_SRV_EN 0x5E /* Enable SERVICE interrupt */ #define WDSF_POD_DS 0x66 #define WDSF_ECC_DS 0x77 #define WDSF_8BIT_PIO_DS 0x81 /* Disable 8bit PIO (CFA featureset) */ #define WDSF_WRITE_CACHE_DS 0x82 #define WDSF_REASSIGN_DS 0x84 #define WDSF_APM_DS 0x85 /* Disable Adv. Power Management */ #define WDSF_PUIS_DS 0x86 /* Disable Power-Up In Standby */ #define WDSF_ECC_EN 0x88 #define WDSF_CFA_MODE1_DS 0x8A /* Disable CFA power mode 1 */ #define WDSF_RMSN_EN 0x95 /* Enable Removable Media Status */ #define WDSF_RETRY_EN 0x99 /* Obsolete in ATA-6 */ #define WDSF_SET_CURRENT 0x9A /* Obsolete in ATA-6 */ #define WDSF_READAHEAD_EN 0xAA #define WDSF_PREFETCH_SET 0xAB /* Obsolete in ATA-6 */ #define WDSF_AAM_DS 0xC2 /* Disable Autom. Acoustic Management */ #define WDSF_POD_EN 0xCC #define WDSF_RLSE_DS 0xDD /* Disable release interrupt */ #define WDSF_SRV_DS 0xDE /* Disable SERVICE interrupt */ /* parameters uploaded to device/heads register */ #define WDSD_IBM 0xa0 /* forced to 512 byte sector, ecc */ #define WDSD_CHS 0x00 /* cylinder/head/sector addressing */ #define WDSD_LBA 0x40 /* logical block addressing */ /* Commands for ATAPI devices */ #define ATAPI_CHECK_POWER_MODE 0xe5 #define ATAPI_EXEC_DRIVE_DIAGS 0x90 #define ATAPI_IDLE_IMMEDIATE 0xe1 #define ATAPI_NOP 0x00 #define ATAPI_PKT_CMD 0xa0 #define ATAPI_IDENTIFY_DEVICE 0xa1 #define ATAPI_SOFT_RESET 0x08 #define ATAPI_DEVICE_RESET 0x08 /* ATA/ATAPI-5 name for soft reset */ #define ATAPI_SLEEP 0xe6 #define ATAPI_STANDBY_IMMEDIATE 0xe0 #define ATAPI_SMART 0xB0 /* SMART operations */ #define ATAPI_SETMAX 0xF9 /* Set Max Address */ #define ATAPI_WRITEEXT 0x34 /* Write sectors Ext */ #define ATAPI_SETMAXEXT 0x37 /* Set Max Address Ext */ #define ATAPI_WRITEMULTIEXT 0x39 /* Write Multi Ext */ /* Bytes used by ATAPI_PACKET_COMMAND ( feature register) */ #define ATAPI_PKT_CMD_FTRE_DMA 0x01 #define ATAPI_PKT_CMD_FTRE_OVL 0x02 /* ireason */ #define WDCI_CMD 0x01 /* command(1) or data(0) */ #define WDCI_IN 0x02 /* transfer to(1) or from(0) the host */ #define WDCI_RELEASE 0x04 /* bus released until completion */ #define PHASE_CMDOUT (WDCS_DRQ | WDCI_CMD) #define PHASE_DATAIN (WDCS_DRQ | WDCI_IN) #define PHASE_DATAOUT WDCS_DRQ #define PHASE_COMPLETED (WDCI_IN | WDCI_CMD) #define PHASE_ABORTED 0