/* $OpenBSD: ahareg.h,v 1.3 1996/05/07 07:36:05 deraadt Exp $ */ typedef u_int8_t physaddr[3]; typedef u_int8_t physlen[3]; #define ltophys _lto3b #define phystol _3btol /* * I/O port offsets */ #define AHA_CTRL_PORT 0 /* control (wo) */ #define AHA_STAT_PORT 0 /* status (ro) */ #define AHA_CMD_PORT 1 /* command (wo) */ #define AHA_DATA_PORT 1 /* data (ro) */ #define AHA_INTR_PORT 2 /* interrupt status (ro) */ /* * AHA_CTRL bits */ #define AHA_CTRL_HRST 0x80 /* Hardware reset */ #define AHA_CTRL_SRST 0x40 /* Software reset */ #define AHA_CTRL_IRST 0x20 /* Interrupt reset */ #define AHA_CTRL_SCRST 0x10 /* SCSI bus reset */ /* * AHA_STAT bits */ #define AHA_STAT_STST 0x80 /* Self test in Progress */ #define AHA_STAT_DIAGF 0x40 /* Diagnostic Failure */ #define AHA_STAT_INIT 0x20 /* Mbx Init required */ #define AHA_STAT_IDLE 0x10 /* Host Adapter Idle */ #define AHA_STAT_CDF 0x08 /* cmd/data out port full */ #define AHA_STAT_DF 0x04 /* Data in port full */ #define AHA_STAT_INVDCMD 0x01 /* Invalid command */ /* * AHA_CMD opcodes */ #define AHA_NOP 0x00 /* No operation */ #define AHA_MBX_INIT 0x01 /* Mbx initialization */ #define AHA_START_SCSI 0x02 /* start scsi command */ #define AHA_INQUIRE_REVISION 0x04 /* Adapter Inquiry */ #define AHA_MBO_INTR_EN 0x05 /* Enable MBO available interrupt */ #if 0 #define AHA_SEL_TIMEOUT_SET 0x06 /* set selection time-out */ #define AHA_BUS_ON_TIME_SET 0x07 /* set bus-on time */ #define AHA_BUS_OFF_TIME_SET 0x08 /* set bus-off time */ #define AHA_SPEED_SET 0x09 /* set transfer speed */ #endif #define AHA_INQUIRE_DEVICES 0x0a /* return installed devices 0-7 */ #define AHA_INQUIRE_CONFIG 0x0b /* return configuration data */ #define AHA_TARGET_EN 0x0c /* enable target mode */ #define AHA_INQUIRE_SETUP 0x0d /* return setup data */ #define AHA_ECHO 0x1e /* Echo command data */ #define AHA_INQUIRE_DEVICES_2 0x23 /* return installed devices 8-15 */ #define AHA_EXT_BIOS 0x28 /* return extended bios info */ #define AHA_MBX_ENABLE 0x29 /* enable mail box interface */ /* * AHA_INTR bits */ #define AHA_INTR_ANYINTR 0x80 /* Any interrupt */ #define AHA_INTR_SCRD 0x08 /* SCSI reset detected */ #define AHA_INTR_HACC 0x04 /* Command complete */ #define AHA_INTR_MBOA 0x02 /* MBX out empty */ #define AHA_INTR_MBIF 0x01 /* MBX in full */ struct aha_mbx_out { u_char cmd; physaddr ccb_addr; }; struct aha_mbx_in { u_char stat; physaddr ccb_addr; }; /* * mbo.cmd values */ #define AHA_MBO_FREE 0x0 /* MBO entry is free */ #define AHA_MBO_START 0x1 /* MBO activate entry */ #define AHA_MBO_ABORT 0x2 /* MBO abort entry */ /* * mbi.stat values */ #define AHA_MBI_FREE 0x0 /* MBI entry is free */ #define AHA_MBI_OK 0x1 /* completed without error */ #define AHA_MBI_ABORT 0x2 /* aborted ccb */ #define AHA_MBI_UNKNOWN 0x3 /* Tried to abort invalid CCB */ #define AHA_MBI_ERROR 0x4 /* Completed with error */ /* FOR OLD VERSIONS OF THE !%$@ this may have to be 16 (yuk) */ #define AHA_NSEG 17 /* Number of scatter gather segments <= 16 */ /* allow 64 K i/o (min) */ struct aha_scat_gath { physlen seg_len; physaddr seg_addr; }; struct aha_ccb { u_char opcode; u_char lun:3; u_char data_in:1; /* must be 0 */ u_char data_out:1; /* must be 0 */ u_char target:3; u_char scsi_cmd_length; u_char req_sense_length; physlen data_length; physaddr data_addr; physaddr link_addr; u_char link_id; u_char host_stat; u_char target_stat; u_char reserved[2]; struct scsi_generic scsi_cmd; struct scsi_sense_data scsi_sense; struct aha_scat_gath scat_gath[AHA_NSEG]; /*----------------------------------------------------------------*/ #define CCB_PHYS_SIZE ((int)&((struct aha_ccb *)0)->chain) TAILQ_ENTRY(aha_ccb) chain; struct aha_ccb *nexthash; struct scsi_xfer *xs; /* the scsi_xfer for this cmd */ int flags; #define CCB_ALLOC 0x01 #define CCB_ABORT 0x02 #ifdef AHADIAG #define CCB_SENDING 0x04 #endif int timeout; struct isadma_seg ccb_phys[1]; /* phys segment of this ccb */ struct isadma_seg data_phys[AHA_NSEG]; /* phys segments of data */ int data_nseg; /* number of phys segments of data */ }; /* * opcode fields */ #define AHA_INITIATOR_CCB 0x00 /* SCSI Initiator CCB */ #define AHA_TARGET_CCB 0x01 /* SCSI Target CCB */ #define AHA_INIT_SCAT_GATH_CCB 0x02 /* SCSI Initiator with scatter gather */ #define AHA_RESET_CCB 0x81 /* SCSI Bus reset */ /* * aha_ccb.host_stat values */ #define AHA_OK 0x00 /* cmd ok */ #define AHA_LINK_OK 0x0a /* Link cmd ok */ #define AHA_LINK_IT 0x0b /* Link cmd ok + int */ #define AHA_SEL_TIMEOUT 0x11 /* Selection time out */ #define AHA_OVER_UNDER 0x12 /* Data over/under run */ #define AHA_BUS_FREE 0x13 /* Bus dropped at unexpected time */ #define AHA_INV_BUS 0x14 /* Invalid bus phase/sequence */ #define AHA_BAD_MBO 0x15 /* Incorrect MBO cmd */ #define AHA_BAD_CCB 0x16 /* Incorrect ccb opcode */ #define AHA_BAD_LINK 0x17 /* Not same values of LUN for links */ #define AHA_INV_TARGET 0x18 /* Invalid target direction */ #define AHA_CCB_DUP 0x19 /* Duplicate CCB received */ #define AHA_INV_CCB 0x1a /* Invalid CCB or segment list */ struct aha_revision { struct { u_char opcode; } cmd; struct { u_char boardid; /* type of board */ /* 0x31 = AHA-1540 */ /* 0x41 = AHA-1540A/1542A/1542B */ /* 0x42 = AHA-1640 */ /* 0x43 = AHA-1542C */ /* 0x44 = AHA-1542CF */ /* 0x45 = AHA-1542CF, BIOS v2.01 */ /* 0x46 = AHA-1542CP */ u_char spec_opts; /* special options ID */ /* 0x41 = Board is standard model */ u_char revision_1; /* firmware revision [0-9A-Z] */ u_char revision_2; /* firmware revision [0-9A-Z] */ } reply; }; struct aha_extbios { struct { u_char opcode; } cmd; struct { u_char flags; /* Bit 3 == 1 extended bios enabled */ u_char mailboxlock; /* mail box lock code to unlock it */ } reply; }; struct aha_toggle { struct { u_char opcode; u_char enable; } cmd; }; struct aha_config { struct { u_char opcode; } cmd; struct { u_char chan; u_char intr; u_char scsi_dev:3; u_char :5; } reply; }; struct aha_mailbox { struct { u_char opcode; u_char nmbx; physaddr addr; } cmd; }; struct aha_unlock { struct { u_char opcode; u_char junk; u_char magic; } cmd; }; struct aha_devices { struct { u_char opcode; } cmd; struct { u_char junk[8]; } reply; }; struct aha_setup { struct { u_char opcode; u_char len; } cmd; struct { u_char sync_neg:1; u_char parity:1; u_char :6; u_char speed; u_char bus_on; u_char bus_off; u_char num_mbx; u_char mbx[3]; struct { u_char offset:4; u_char period:3; u_char valid:1; } sync[8]; u_char disc_sts; } reply; }; #define INT9 0x01 #define INT10 0x02 #define INT11 0x04 #define INT12 0x08 #define INT14 0x20 #define INT15 0x40 #define EISADMA 0x00 #define CHAN0 0x01 #define CHAN5 0x20 #define CHAN6 0x40 #define CHAN7 0x80