/* $OpenBSD: if_ed.c,v 1.25 1996/11/29 22:54:58 niklas Exp $ */ /* $NetBSD: if_ed.c,v 1.105 1996/10/21 22:40:45 thorpej Exp $ */ /* * Device driver for National Semiconductor DS8390/WD83C690 based ethernet * adapters. * * Copyright (c) 1994, 1995 Charles M. Hannum. All rights reserved. * * Copyright (C) 1993, David Greenman. This software may be used, modified, * copied, distributed, and sold, in both source and binary form provided that * the above copyright and these terms are retained. Under no circumstances is * the author responsible for the proper functioning of this software, nor does * the author assume any responsibility for damages incurred with its use. * * Currently supports the Western Digital/SMC 8003 and 8013 series, the SMC * Elite Ultra (8216), the 3Com 3c503, the NE1000 and NE2000, and a variety of * similar clones. */ #include "bpfilter.h" #include "ed.h" #include #include #include #include #include #include #include #include #include #include #include #include #ifdef INET #include #include #include #include #include #endif #if NBPFILTER > 0 #include #include #endif #include #include #include #include #include #include #include /* * ed_softc: per line info and status */ struct ed_softc { struct device sc_dev; void *sc_ih; struct arpcom sc_arpcom; /* ethernet common */ void *sc_sh; /* shutdown hook */ char *type_str; /* pointer to type string */ u_char vendor; /* interface vendor */ u_char type; /* interface type code */ u_short spec_flags; #define ED_REATTACH 0x0001 /* Reattach */ #define ED_NOTPRESENT 0x0002 /* card not present; do not allow reconfiguration */ bus_space_tag_t sc_iot; /* bus identifier */ bus_space_tag_t sc_memt; bus_space_handle_t sc_ioh; /* io handle */ bus_space_handle_t sc_delaybah; /* io handle for `delay port' */ bus_space_handle_t sc_memh; /* bus memory handle */ isa_chipset_tag_t sc_ic; bus_size_t asic_base; /* offset of ASIC I/O port */ bus_size_t nic_base; /* offset of NIC (DS8390) I/O port */ /* * The following 'proto' variable is part of a work-around for 8013EBT asics * being write-only. It's sort of a prototype/shadow of the real thing. */ u_char wd_laar_proto; /* * This `proto' variable is so we can turn MENB on and off without reading * the value back from the card all the time. */ u_char wd_msr_proto; u_char cr_proto; /* values always set in CR */ u_char isa16bit; /* width of access to card 0=8 or 1=16 */ u_char is790; /* set by probe if NIC is a 790 */ int mem_start; /* offset of NIC memory */ int mem_end; /* offset of NIC memory end */ int mem_size; /* total NIC memory size */ int mem_ring; /* offset of RX ring-buffer (in NIC mem) */ u_char mem_shared; /* NIC memory is shared with host */ u_char txb_cnt; /* number of transmit buffers */ u_char txb_inuse; /* number of transmit buffers active */ u_char txb_new; /* pointer to where new buffer will be added */ u_char txb_next_tx; /* pointer to next buffer ready to xmit */ u_short txb_len[8]; /* buffered xmit buffer lengths */ u_char tx_page_start; /* first page of TX buffer area */ u_char rec_page_start; /* first page of RX ring-buffer */ u_char rec_page_stop; /* last page of RX ring-buffer */ u_char next_packet; /* pointer to next unread RX packet */ }; int edprobe __P((struct device *, void *, void *)); void edattach __P((struct device *, struct device *, void *)); int ed_find __P((struct ed_softc *, struct cfdata *, struct isa_attach_args *ia)); int ed_probe_generic8390 __P((bus_space_tag_t, bus_space_handle_t, int)); int ed_find_WD80x3 __P((struct ed_softc *, struct cfdata *, struct isa_attach_args *ia)); int ed_find_3Com __P((struct ed_softc *, struct cfdata *, struct isa_attach_args *ia)); int ed_find_Novell __P((struct ed_softc *, struct cfdata *, struct isa_attach_args *ia)); int edintr __P((void *)); int edioctl __P((struct ifnet *, u_long, caddr_t)); void edstart __P((struct ifnet *)); void edwatchdog __P((struct ifnet *)); void edreset __P((struct ed_softc *)); void edinit __P((struct ed_softc *)); void edstop __P((struct ed_softc *)); void ed_shared_writemem __P((struct ed_softc *, caddr_t, int, int)); void ed_shared_readmem __P((struct ed_softc *, int, caddr_t, int)); #define inline /* XXX for debugging porpoises */ void ed_getmcaf __P((struct arpcom *, u_long *)); void edread __P((struct ed_softc *, int, int)); struct mbuf *edget __P((struct ed_softc *, int, int)); static __inline void ed_rint __P((struct ed_softc *)); static __inline void ed_xmit __P((struct ed_softc *)); static __inline int ed_ring_copy __P((struct ed_softc *, int, caddr_t, u_short)); void ed_pio_readmem __P((struct ed_softc *, u_short, caddr_t, u_short)); void ed_pio_writemem __P((struct ed_softc *, caddr_t, u_short, u_short)); u_short ed_pio_write_mbufs __P((struct ed_softc *, struct mbuf *, u_short)); #if NED_ISA > 0 struct cfattach ed_isa_ca = { sizeof(struct ed_softc), edprobe, edattach }; #endif struct cfdriver ed_cd = { NULL, "ed", DV_IFNET }; #define ETHER_MIN_LEN 64 #define ETHER_MAX_LEN 1518 #define ETHER_ADDR_LEN 6 #if NED_PCMCIA > 0 #include int ed_pcmcia_match __P((struct device *, void *, void *)); void ed_pcmcia_attach __P((struct device *, struct device *, void *)); int ed_pcmcia_detach __P((struct device *)); struct cfattach ed_pcmcia_ca = { sizeof(struct ed_softc), ed_pcmcia_match, edattach, ed_pcmcia_detach }; int ed_pcmcia_isa_attach __P((struct device *, void *, void *, struct pcmcia_link *)); int edmod __P((struct pcmcia_link *, struct device *, struct pcmcia_conf *, struct cfdata *cf)); int ed_remove __P((struct pcmcia_link *, struct device *)); /* additional setup needed for pcmcia devices */ int ed_pcmcia_isa_attach(parent, match, aux, pc_link) struct device *parent; void *match; void *aux; struct pcmcia_link *pc_link; { struct ed_softc *sc = match; struct cfdata *cf = sc->sc_dev.dv_cfdata; struct isa_attach_args *ia = aux; struct pcmciadevs *dev=pc_link->device; int err; extern int ifqmaxlen; u_char enaddr[ETHER_ADDR_LEN]; if ((int)dev->param != -1) err = pcmcia_read_cis(pc_link, enaddr, (int) dev->param, ETHER_ADDR_LEN); else err = 0; if (err) printf("%s: attaching ed: cannot read cis info %d\n", parent->dv_xname, err); if (ed_find_Novell(sc, cf, ia)) { delay(100); if ((int)dev->param != -1) { err = pcmcia_read_cis(pc_link, sc->sc_arpcom.ac_enaddr, (int) dev->param, ETHER_ADDR_LEN); if (err) { printf("Cannot read cis info %d\n", err); return 0; } if(bcmp(enaddr, sc->sc_arpcom.ac_enaddr, ETHER_ADDR_LEN)) { printf("ENADDR MISMATCH %s ", ether_sprintf(sc->sc_arpcom.ac_enaddr)); printf("- %s\n", ether_sprintf(enaddr)); bcopy(enaddr,sc->sc_arpcom.ac_enaddr, ETHER_ADDR_LEN); } } /* clear ED_NOTPRESENT, set ED_REATTACH if needed */ sc->spec_flags=pc_link->flags&PCMCIA_REATTACH?ED_REATTACH:0; sc->type_str = dev->model; sc->sc_arpcom.ac_if.if_snd.ifq_maxlen=ifqmaxlen; sc->sc_ic = ia->ia_ic; return 1; } else return 0; } /* modify config entry */ int edmod(pc_link, self, pc_cf, cf) struct pcmcia_link *pc_link; struct device *self; struct pcmcia_conf *pc_cf; struct cfdata *cf; { int err; /* struct pcmciadevs *dev=pc_link->device;*/ /* struct ed_softc *sc = (void *)self;*/ int svec_card = pc_cf->memwin == 5; int de650_0 = (pc_cf->memwin != 0) && !svec_card; err = PCMCIA_BUS_CONFIG(pc_link->adapter, pc_link, self, pc_cf, cf); if (err) return err; if (svec_card) { pc_cf->memwin = 0; #if 0 pc_cf->cfgid = 32; /* Try this if it still doesn't work */ pc_cf->cfgid |= 32; /* or Try this if it still doesn't work */ #endif } if (de650_0) { pc_cf->io[0].flags = (pc_cf->io[0].flags&~PCMCIA_MAP_16)|PCMCIA_MAP_8; pc_cf->memwin = 0; pc_cf->cfgtype = DOSRESET|1; } else { /* still wrong in CIS; fix it here */ pc_cf->io[0].flags = PCMCIA_MAP_8|PCMCIA_MAP_16; pc_cf->cfgtype = 1; } return err; } int ed_remove(pc_link,self) struct pcmcia_link *pc_link; struct device *self; { struct ed_softc *sc = (void *)self; struct ifnet *ifp = &sc->sc_arpcom.ac_if; if_down(ifp); edstop(sc); shutdownhook_disestablish(sc->sc_sh); ifp->if_flags &= ~(IFF_RUNNING|IFF_UP); sc->spec_flags |= ED_NOTPRESENT; isa_intr_disestablish(sc->sc_ic, sc->sc_ih); return PCMCIA_BUS_UNCONFIG(pc_link->adapter, pc_link); } static struct pcmcia_dlink { struct pcmcia_device pcd; } pcmcia_dlink = { {"PCMCIA Novell compatible", edmod, ed_pcmcia_isa_attach, NULL, ed_remove} }; struct pcmciadevs pcmcia_ed_devs[]={ { "ed", 0, "D-Link", "DE-650", "Ver 01.00", NULL, (void *) -1, (void *)&pcmcia_dlink }, { "ed", 0, "D-Link", "DE-650", "", NULL, (void *) 0x40, (void *)&pcmcia_dlink }, { "ed", 0, "LINKSYS", "E-CARD", "Ver 01.00", NULL, (void *)-1, (void *)&pcmcia_dlink }, { "ed", 0, "IBM Corp.", "Ethernet", "0933495", NULL, (void *) 0xff0, (void *)&pcmcia_dlink }, { "ed", 0, "Socket Communications Inc", "Socket EA PCMCIA LAN Adapter Revision D", "Ethernet ID 000000000000", NULL, (void *) -1, (void *)&pcmcia_dlink }, /* something screwed up in ports requested */ { "ed", 0, "SVEC", "FD605 PCMCIA EtherNet Card", "V1-1", NULL, (void *)-1, (void *)&pcmcia_dlink }, #if 0 /* not quite right for ethernet adress */ { "ed", 0, "PMX ", "PE-200", "ETHERNET", "R01", (void *)-1, (void *)&pcmcia_dlink }, #endif { NULL } }; #define ned_pcmcia_devs sizeof(pcmcia_ed_devs)/sizeof(pcmcia_ed_devs[0]) int ed_pcmcia_match(parent, match, aux) struct device *parent; void *match, *aux; { return pcmcia_slave_match(parent, match, aux, pcmcia_ed_devs, ned_pcmcia_devs); } void ed_pcmcia_attach(parent, self, aux) struct device *parent, *self; void *aux; { struct pcmcia_attach_args *paa = aux; printf("ed_pcmcia_attach %p %p %p\n", parent, self, aux); delay(2000000); if (!pcmcia_configure(parent, self, paa->paa_link)) { struct ed_softc *sc = (void *)self; sc->spec_flags |= ED_NOTPRESENT; printf(": not attached\n"); } } /* * No detach; network devices are too well linked into the rest of the * kernel. */ int ed_pcmcia_detach(self) struct device *self; { return EBUSY; } #endif #define NIC_PUT(t, bah, nic, reg, val) \ bus_space_write_1((t), (bah), ((nic) + (reg)), (val)) #define NIC_GET(t, bah, nic, reg) \ bus_space_read_1((t), (bah), ((nic) + (reg))) /* * Determine if the device is present. */ int edprobe(parent, match, aux) struct device *parent; void *match, *aux; { struct ed_softc *sc = match; return (ed_find(match, sc->sc_dev.dv_cfdata, aux)); } /* * Fill in softc (if given), based on device type, cfdata and attach args. * Return 1 if successful, 0 otherwise. */ int ed_find(sc, cf, ia) struct ed_softc *sc; struct cfdata *cf; struct isa_attach_args *ia; { if (ed_find_WD80x3(sc, cf, ia)) return (1); if (ed_find_3Com(sc, cf, ia)) return (1); if (ed_find_Novell(sc, cf, ia)) return (1); return (0); } /* * Generic probe routine for testing for the existance of a DS8390. Must be * called after the NIC has just been reset. This routine works by looking at * certain register values that are guaranteed to be initialized a certain way * after power-up or reset. Seems not to currently work on the 83C690. * * Specifically: * * Register reset bits set bits * Command Register (CR) TXP, STA RD2, STP * Interrupt Status (ISR) RST * Interrupt Mask (IMR) All bits * Data Control (DCR) LAS * Transmit Config. (TCR) LB1, LB0 * * We only look at the CR and ISR registers, however, because looking at the * others would require changing register pages (which would be intrusive if * this isn't an 8390). * * Return 1 if 8390 was found, 0 if not. */ int ed_probe_generic8390(t, bah, nicbase) bus_space_tag_t t; bus_space_handle_t bah; int nicbase; { if ((NIC_GET(t, bah, nicbase, ED_P0_CR) & (ED_CR_RD2 | ED_CR_TXP | ED_CR_STA | ED_CR_STP)) != (ED_CR_RD2 | ED_CR_STP)) return (0); if ((NIC_GET(t, bah, nicbase, ED_P0_ISR) & ED_ISR_RST) != ED_ISR_RST) return (0); return (1); } int ed_wd584_irq[] = { 9, 3, 5, 7, 10, 11, 15, 4 }; int ed_wd790_irq[] = { IRQUNK, 9, 3, 5, 7, 10, 11, 15 }; /* * Probe and vendor-specific initialization routine for SMC/WD80x3 boards. */ int ed_find_WD80x3(sc, cf, ia) struct ed_softc *sc; struct cfdata *cf; struct isa_attach_args *ia; { bus_space_tag_t iot; bus_space_tag_t memt; bus_space_handle_t ioh; bus_space_handle_t delaybah = ia->ia_delaybah; bus_space_handle_t memh; u_int memsize; u_char iptr, isa16bit, sum; int i, rv, memfail, mapped_mem = 0; int asicbase, nicbase; iot = ia->ia_iot; memt = ia->ia_memt; rv = 0; /* Set initial values for width/size. */ memsize = 8192; isa16bit = 0; if (bus_space_map(iot, ia->ia_iobase, ED_WD_IO_PORTS, 0, &ioh)) return (0); sc->asic_base = asicbase = 0; sc->nic_base = nicbase = asicbase + ED_WD_NIC_OFFSET; sc->is790 = 0; #ifdef TOSH_ETHER bus_space_write_1(iot, ioh, asicbase + ED_WD_MSR, ED_WD_MSR_POW); delay(10000); #endif /* * Attempt to do a checksum over the station address PROM. If it * fails, it's probably not a SMC/WD board. There is a problem with * this, though: some clone WD boards don't pass the checksum test. * Danpex boards for one. */ for (sum = 0, i = 0; i < 8; ++i) sum += bus_space_read_1(iot, ioh, asicbase + ED_WD_PROM + i); if (sum != ED_WD_ROM_CHECKSUM_TOTAL) { /* * Checksum is invalid. This often happens with cheap WD8003E * clones. In this case, the checksum byte (the eighth byte) * seems to always be zero. */ if (bus_space_read_1(iot, ioh, asicbase + ED_WD_CARD_ID) != ED_TYPE_WD8003E || bus_space_read_1(iot, ioh, asicbase + ED_WD_PROM + 7) != 0) goto out; } /* Reset card to force it into a known state. */ #ifdef TOSH_ETHER bus_space_write_1(iot, ioh, asicbase + ED_WD_MSR, ED_WD_MSR_RST | ED_WD_MSR_POW); #else bus_space_write_1(iot, ioh, asicbase + ED_WD_MSR, ED_WD_MSR_RST); #endif delay(100); bus_space_write_1(iot, ioh, asicbase + ED_WD_MSR, bus_space_read_1(iot, ioh, asicbase + ED_WD_MSR) & ~ED_WD_MSR_RST); /* Wait in the case this card is reading it's EEROM. */ delay(5000); sc->vendor = ED_VENDOR_WD_SMC; sc->type = bus_space_read_1(iot, ioh, asicbase + ED_WD_CARD_ID); switch (sc->type) { case ED_TYPE_WD8003S: sc->type_str = "WD8003S"; break; case ED_TYPE_WD8003E: sc->type_str = "WD8003E"; break; case ED_TYPE_WD8003EB: sc->type_str = "WD8003EB"; break; case ED_TYPE_WD8003W: sc->type_str = "WD8003W"; break; case ED_TYPE_WD8013EBT: sc->type_str = "WD8013EBT"; memsize = 16384; isa16bit = 1; break; case ED_TYPE_WD8013W: sc->type_str = "WD8013W"; memsize = 16384; isa16bit = 1; break; case ED_TYPE_WD8013EP: /* also WD8003EP */ if (bus_space_read_1(iot, ioh, asicbase + ED_WD_ICR) & ED_WD_ICR_16BIT) { isa16bit = 1; memsize = 16384; sc->type_str = "WD8013EP"; } else sc->type_str = "WD8003EP"; break; case ED_TYPE_WD8013WC: sc->type_str = "WD8013WC"; memsize = 16384; isa16bit = 1; break; case ED_TYPE_WD8013EBP: sc->type_str = "WD8013EBP"; memsize = 16384; isa16bit = 1; break; case ED_TYPE_WD8013EPC: sc->type_str = "WD8013EPC"; memsize = 16384; isa16bit = 1; break; case ED_TYPE_SMC8216C: case ED_TYPE_SMC8216T: sc->type_str = (sc->type == ED_TYPE_SMC8216C) ? "SMC8216/SMC8216C" : "SMC8216T"; bus_space_write_1(iot, ioh, asicbase + ED_WD790_HWR, bus_space_read_1(iot, ioh, asicbase + ED_WD790_HWR) | ED_WD790_HWR_SWH); switch (bus_space_read_1(iot, ioh, asicbase + ED_WD790_RAR) & ED_WD790_RAR_SZ64) { case ED_WD790_RAR_SZ64: memsize = 65536; break; case ED_WD790_RAR_SZ32: memsize = 32768; break; case ED_WD790_RAR_SZ16: memsize = 16384; break; case ED_WD790_RAR_SZ8: /* 8216 has 16K shared mem -- 8416 has 8K */ sc->type_str = (sc->type == ED_TYPE_SMC8216C) ? "SMC8416C/SMC8416BT" : "SMC8416T"; memsize = 8192; break; } bus_space_write_1(iot, ioh, asicbase + ED_WD790_HWR, bus_space_read_1(iot, ioh, asicbase + ED_WD790_HWR) & ~ED_WD790_HWR_SWH); isa16bit = 1; sc->is790 = 1; break; #ifdef TOSH_ETHER case ED_TYPE_TOSHIBA1: sc->type_str = "Toshiba1"; memsize = 32768; isa16bit = 1; break; case ED_TYPE_TOSHIBA4: sc->type_str = "Toshiba4"; memsize = 32768; isa16bit = 1; break; #endif default: sc->type_str = NULL; break; } /* * Make some adjustments to initial values depending on what is found * in the ICR. */ if (isa16bit && (sc->type != ED_TYPE_WD8013EBT) && #ifdef TOSH_ETHER (sc->type != ED_TYPE_TOSHIBA1) && (sc->type != ED_TYPE_TOSHIBA4) && #endif ((bus_space_read_1(iot, ioh, asicbase + ED_WD_ICR) & ED_WD_ICR_16BIT) == 0)) { isa16bit = 0; memsize = 8192; } #ifdef ED_DEBUG printf("type=%x type_str=%s isa16bit=%d memsize=%d id_msize=%d\n", sc->type, sc->type_str ?: "unknown", isa16bit, memsize, ia->ia_msize); for (i = 0; i < 8; i++) printf("%x -> %x\n", i, bus_space_read_1(iot, ioh, asicbase + i)); #endif /* Allow the user to override the autoconfiguration. */ if (ia->ia_msize) memsize = ia->ia_msize; /* * (Note that if the user specifies both of the following flags that * '8-bit' mode intentionally has precedence.) */ if (cf->cf_flags & ED_FLAGS_FORCE_16BIT_MODE) isa16bit = 1; if (cf->cf_flags & ED_FLAGS_FORCE_8BIT_MODE) isa16bit = 0; /* * If possible, get the assigned interrupt number from the card and * use it. */ if (sc->is790) { u_char x; /* Assemble together the encoded interrupt number. */ bus_space_write_1(iot, ioh, ED_WD790_HWR, bus_space_read_1(iot, ioh, ED_WD790_HWR) | ED_WD790_HWR_SWH); x = bus_space_read_1(iot, ioh, ED_WD790_GCR); iptr = ((x & ED_WD790_GCR_IR2) >> 4) | ((x & (ED_WD790_GCR_IR1|ED_WD790_GCR_IR0)) >> 2); bus_space_write_1(iot, ioh, ED_WD790_HWR, bus_space_read_1(iot, ioh, ED_WD790_HWR) & ~ED_WD790_HWR_SWH); /* * Translate it using translation table, and check for * correctness. */ if (ia->ia_irq != IRQUNK) { if (ia->ia_irq != ed_wd790_irq[iptr]) { printf("%s: irq mismatch; kernel configured %d != board configured %d\n", sc->sc_dev.dv_xname, ia->ia_irq, ed_wd790_irq[iptr]); goto out; } } else ia->ia_irq = ed_wd790_irq[iptr]; /* Enable the interrupt. */ bus_space_write_1(iot, ioh, ED_WD790_ICR, bus_space_read_1(iot, ioh, ED_WD790_ICR) | ED_WD790_ICR_EIL); } else if (sc->type & ED_WD_SOFTCONFIG) { /* Assemble together the encoded interrupt number. */ iptr = (bus_space_read_1(iot, ioh, ED_WD_ICR) & ED_WD_ICR_IR2) | ((bus_space_read_1(iot, ioh, ED_WD_IRR) & (ED_WD_IRR_IR0 | ED_WD_IRR_IR1)) >> 5); /* * Translate it using translation table, and check for * correctness. */ if (ia->ia_irq != IRQUNK) { if (ia->ia_irq != ed_wd584_irq[iptr]) { printf("%s: irq mismatch; kernel configured %d != board configured %d\n", sc->sc_dev.dv_xname, ia->ia_irq, ed_wd584_irq[iptr]); goto out; } } else ia->ia_irq = ed_wd584_irq[iptr]; /* Enable the interrupt. */ bus_space_write_1(iot, ioh, ED_WD_IRR, bus_space_read_1(iot, ioh, ED_WD_IRR) | ED_WD_IRR_IEN); } else { if (ia->ia_irq == IRQUNK) { printf("%s: %s does not have soft configuration\n", sc->sc_dev.dv_xname, sc->type_str); goto out; } } /* XXX Figure out the shared memory address. */ sc->isa16bit = isa16bit; sc->mem_shared = 1; ia->ia_msize = memsize; if (bus_space_map(memt, ia->ia_maddr, memsize, 0, &memh)) goto out; mapped_mem = 1; sc->mem_start = 0; /* offset */ /* Allocate one xmit buffer if < 16k, two buffers otherwise. */ if ((memsize < 16384) || (cf->cf_flags & ED_FLAGS_NO_MULTI_BUFFERING)) sc->txb_cnt = 1; else sc->txb_cnt = 2; sc->tx_page_start = ED_WD_PAGE_OFFSET; sc->rec_page_start = sc->tx_page_start + sc->txb_cnt * ED_TXBUF_SIZE; sc->rec_page_stop = sc->tx_page_start + (memsize >> ED_PAGE_SHIFT); sc->mem_ring = sc->mem_start + (sc->rec_page_start << ED_PAGE_SHIFT); sc->mem_size = memsize; sc->mem_end = sc->mem_start + memsize; /* Get station address from on-board ROM. */ for (i = 0; i < ETHER_ADDR_LEN; ++i) sc->sc_arpcom.ac_enaddr[i] = bus_space_read_1(iot, ioh, asicbase + ED_WD_PROM + i); /* * Set upper address bits and 8/16 bit access to shared memory. */ if (isa16bit) { if (sc->is790) { sc->wd_laar_proto = bus_space_read_1(iot, ioh, asicbase + ED_WD_LAAR) & ~ED_WD_LAAR_M16EN; } else { sc->wd_laar_proto = ED_WD_LAAR_L16EN | ((ia->ia_maddr >> 19) & ED_WD_LAAR_ADDRHI); } bus_space_write_1(iot, ioh, asicbase + ED_WD_LAAR, sc->wd_laar_proto | ED_WD_LAAR_M16EN); } else { if ((sc->type & ED_WD_SOFTCONFIG) || #ifdef TOSH_ETHER (sc->type == ED_TYPE_TOSHIBA1) || (sc->type == ED_TYPE_TOSHIBA4) || #endif ((sc->type == ED_TYPE_WD8013EBT) && !sc->is790)) { sc->wd_laar_proto = ((ia->ia_maddr >> 19) & ED_WD_LAAR_ADDRHI); bus_space_write_1(iot, ioh, asicbase + ED_WD_LAAR, sc->wd_laar_proto); } } /* * Set address and enable interface shared memory. */ if (!sc->is790) { #ifdef TOSH_ETHER bus_space_write_1(iot, ioh, asicbase + ED_WD_MSR + 1, ((ia->ia_maddr >> 8) & 0xe0) | 4); bus_space_write_1(iot, ioh, asicbase + ED_WD_MSR + 2, ((ia->ia_maddr >> 16) & 0x0f)); sc->wd_msr_proto = ED_WD_MSR_POW; #else sc->wd_msr_proto = (ia->ia_maddr >> 13) & ED_WD_MSR_ADDR; #endif sc->cr_proto = ED_CR_RD2; } else { bus_space_write_1(iot, ioh, asicbase + 0x04, bus_space_read_1(iot, ioh, asicbase + 0x04) | 0x80); bus_space_write_1(iot, ioh, asicbase + 0x0b, ((ia->ia_maddr >> 13) & 0x0f) | ((ia->ia_maddr >> 11) & 0x40) | (bus_space_read_1(iot, ioh, asicbase + 0x0b) & 0xb0)); bus_space_write_1(iot, ioh, asicbase + 0x04, bus_space_read_1(iot, ioh, asicbase + 0x04) & ~0x80); sc->wd_msr_proto = 0x00; sc->cr_proto = 0; } bus_space_write_1(iot, ioh, asicbase + ED_WD_MSR, sc->wd_msr_proto | ED_WD_MSR_MENB); (void) bus_space_read_1(iot, delaybah, 0); (void) bus_space_read_1(iot, delaybah, 0); /* Now zero memory and verify that it is clear. */ if (isa16bit) { for (i = 0; i < memsize; i += 2) bus_space_write_2(memt, memh, sc->mem_start + i, 0); } else { for (i = 0; i < memsize; ++i) bus_space_write_1(memt, memh, sc->mem_start + i, 0); } memfail = 0; if (isa16bit) { for (i = 0; i < memsize; i += 2) { if (bus_space_read_2(memt, memh, sc->mem_start + i)) { memfail = 1; break; } } } else { for (i = 0; i < memsize; ++i) { if (bus_space_read_1(memt, memh, sc->mem_start + i)) { memfail = 1; break; } } } if (memfail) { printf("%s: failed to clear shared memory at %x - " "check configuration\n", sc->sc_dev.dv_xname, (ia->ia_maddr + sc->mem_start + i)); /* Disable 16 bit access to shared memory. */ bus_space_write_1(iot, ioh, asicbase + ED_WD_MSR, sc->wd_msr_proto); if (isa16bit) bus_space_write_1(iot, ioh, asicbase + ED_WD_LAAR, sc->wd_laar_proto); (void) bus_space_read_1(iot, delaybah, 0); (void) bus_space_read_1(iot, delaybah, 0); goto out; } /* * Disable 16bit access to shared memory - we leave it disabled * so that 1) machines reboot properly when the board is set 16 * 16 bit mode and there are conflicting 8bit devices/ROMS in * the same 128k address space as this boards shared memory, * and 2) so that other 8 bit devices with shared memory can be * used in this 128k region, too. */ bus_space_write_1(iot, ioh, asicbase + ED_WD_MSR, sc->wd_msr_proto); if (isa16bit) bus_space_write_1(iot, ioh, asicbase + ED_WD_LAAR, sc->wd_laar_proto); (void) bus_space_read_1(iot, delaybah, 0); (void) bus_space_read_1(iot, delaybah, 0); ia->ia_iosize = ED_WD_IO_PORTS; rv = 1; out: /* * XXX Sould always unmap, but we can't yet. * XXX Need to squish "indirect" first. */ if (rv == 0) { bus_space_unmap(iot, ioh, ED_WD_IO_PORTS); if (mapped_mem) bus_space_unmap(memt, memh, memsize); } else { /* XXX this is all "indirect" brokenness */ sc->sc_iot = iot; sc->sc_memt = memt; sc->sc_ioh = ioh; sc->sc_memh = memh; } return (rv); } int ed_3com_iobase[] = {0x2e0, 0x2a0, 0x280, 0x250, 0x350, 0x330, 0x310, 0x300}; int ed_3com_maddr[] = { MADDRUNK, MADDRUNK, MADDRUNK, MADDRUNK, 0xc8000, 0xcc000, 0xd8000, 0xdc000 }; #if 0 int ed_3com_irq[] = {IRQUNK, IRQUNK, IRQUNK, IRQUNK, 9, 3, 4, 5}; #endif /* * Probe and vendor-specific initialization routine for 3Com 3c503 boards. */ int ed_find_3Com(sc, cf, ia) struct ed_softc *sc; struct cfdata *cf; struct isa_attach_args *ia; { bus_space_tag_t iot; bus_space_tag_t memt; bus_space_handle_t ioh; bus_space_handle_t memh; int i; u_int memsize, memfail; u_char isa16bit, x; int ptr, asicbase, nicbase; /* * Hmmm...a 16bit 3Com board has 16k of memory, but only an 8k window * to it. */ memsize = 8192; iot = ia->ia_iot; memt = ia->ia_memt; if (bus_space_map(iot, ia->ia_iobase, ED_3COM_IO_PORTS, 0, &ioh)) return (0); sc->asic_base = asicbase = ED_3COM_ASIC_OFFSET; sc->nic_base = nicbase = ED_3COM_NIC_OFFSET; /* * Verify that the kernel configured I/O address matches the board * configured address. * * This is really only useful to see if something that looks like the * board is there; after all, we are already talking it at that * address. */ x = bus_space_read_1(iot, ioh, asicbase + ED_3COM_BCFR); if (x == 0 || (x & (x - 1)) != 0) goto err; ptr = ffs(x) - 1; if (ia->ia_iobase != IOBASEUNK) { if (ia->ia_iobase != ed_3com_iobase[ptr]) { printf("%s: %s mismatch; kernel configured %x != board configured %x\n", "iobase", sc->sc_dev.dv_xname, ia->ia_iobase, ed_3com_iobase[ptr]); goto err; } } else ia->ia_iobase = ed_3com_iobase[ptr]; /* XXX --thorpej */ x = bus_space_read_1(iot, ioh, asicbase + ED_3COM_PCFR); if (x == 0 || (x & (x - 1)) != 0) { printf("%s: The 3c503 is not currently supported with memory " "mapping disabled.\n%s: Reconfigure the card to " "enable memory mapping.\n", sc->sc_dev.dv_xname, sc->sc_dev.dv_xname); goto err; } ptr = ffs(x) - 1; if (ia->ia_maddr != MADDRUNK) { if (ia->ia_maddr != ed_3com_maddr[ptr]) { printf("%s: %s mismatch; kernel configured %x != board configured %x\n", "maddr", sc->sc_dev.dv_xname, ia->ia_maddr, ed_3com_maddr[ptr]); goto err; } } else ia->ia_maddr = ed_3com_maddr[ptr]; #if 0 x = bus_space_read_1(iot, ioh, asicbase + ED_3COM_IDCFR) & ED_3COM_IDCFR_IRQ; if (x == 0 || (x & (x - 1)) != 0) goto out; ptr = ffs(x) - 1; if (ia->ia_irq != IRQUNK) { if (ia->ia_irq != ed_3com_irq[ptr]) { printf("%s: irq mismatch; kernel configured %d != board configured %d\n", sc->sc_dev.dv_xname, ia->ia_irq, ed_3com_irq[ptr]); goto err; } } else ia->ia_irq = ed_3com_irq[ptr]; #endif /* * Reset NIC and ASIC. Enable on-board transceiver throughout reset * sequence because it'll lock up if the cable isn't connected if we * don't. */ bus_space_write_1(iot, ioh, asicbase + ED_3COM_CR, ED_3COM_CR_RST | ED_3COM_CR_XSEL); /* Wait for a while, then un-reset it. */ delay(50); /* * The 3Com ASIC defaults to rather strange settings for the CR after a * reset - it's important to set it again after the following outb * (this is done when we map the PROM below). */ bus_space_write_1(iot, ioh, asicbase + ED_3COM_CR, ED_3COM_CR_XSEL); /* Wait a bit for the NIC to recover from the reset. */ delay(5000); sc->vendor = ED_VENDOR_3COM; sc->type_str = "3c503"; sc->mem_shared = 1; sc->cr_proto = ED_CR_RD2; /* * Get station address from on-board ROM. * * First, map ethernet address PROM over the top of where the NIC * registers normally appear. */ bus_space_write_1(iot, ioh, asicbase + ED_3COM_CR, ED_3COM_CR_EALO | ED_3COM_CR_XSEL); for (i = 0; i < ETHER_ADDR_LEN; ++i) sc->sc_arpcom.ac_enaddr[i] = NIC_GET(iot, ioh, nicbase, i); /* * Unmap PROM - select NIC registers. The proper setting of the * tranceiver is set in edinit so that the attach code is given a * chance to set the default based on a compile-time config option. */ bus_space_write_1(iot, ioh, asicbase + ED_3COM_CR, ED_3COM_CR_XSEL); /* Determine if this is an 8bit or 16bit board. */ /* Select page 0 registers. */ NIC_PUT(iot, ioh, nicbase, ED_P0_CR, ED_CR_RD2 | ED_CR_PAGE_0 | ED_CR_STP); /* * Attempt to clear WTS bit. If it doesn't clear, then this is a * 16-bit board. */ NIC_PUT(iot, ioh, nicbase, ED_P0_DCR, 0); /* Select page 2 registers. */ NIC_PUT(iot, ioh, nicbase, ED_P0_CR, ED_CR_RD2 | ED_CR_PAGE_2 | ED_CR_STP); /* The 3c503 forces the WTS bit to a one if this is a 16bit board. */ if (NIC_GET(iot, ioh, nicbase, ED_P2_DCR) & ED_DCR_WTS) isa16bit = 1; else isa16bit = 0; /* Select page 0 registers. */ NIC_PUT(iot, ioh, nicbase, ED_P2_CR, ED_CR_RD2 | ED_CR_PAGE_0 | ED_CR_STP); if (bus_space_map(memt, ia->ia_maddr, memsize, 0, &memh)) goto err; sc->mem_start = 0; /* offset */ sc->mem_size = memsize; sc->mem_end = sc->mem_start + memsize; /* * We have an entire 8k window to put the transmit buffers on the * 16-bit boards. But since the 16bit 3c503's shared memory is only * fast enough to overlap the loading of one full-size packet, trying * to load more than 2 buffers can actually leave the transmitter idle * during the load. So 2 seems the best value. (Although a mix of * variable-sized packets might change this assumption. Nonetheless, * we optimize for linear transfers of same-size packets.) */ if (isa16bit) { if (cf->cf_flags & ED_FLAGS_NO_MULTI_BUFFERING) sc->txb_cnt = 1; else sc->txb_cnt = 2; sc->tx_page_start = ED_3COM_TX_PAGE_OFFSET_16BIT; sc->rec_page_start = ED_3COM_RX_PAGE_OFFSET_16BIT; sc->rec_page_stop = (memsize >> ED_PAGE_SHIFT) + ED_3COM_RX_PAGE_OFFSET_16BIT; sc->mem_ring = sc->mem_start; } else { sc->txb_cnt = 1; sc->tx_page_start = ED_3COM_TX_PAGE_OFFSET_8BIT; sc->rec_page_start = ED_TXBUF_SIZE + ED_3COM_TX_PAGE_OFFSET_8BIT; sc->rec_page_stop = (memsize >> ED_PAGE_SHIFT) + ED_3COM_TX_PAGE_OFFSET_8BIT; sc->mem_ring = sc->mem_start + (ED_TXBUF_SIZE << ED_PAGE_SHIFT); } sc->isa16bit = isa16bit; /* * Initialize GA page start/stop registers. Probably only needed if * doing DMA, but what the Hell. */ bus_space_write_1(iot, ioh, asicbase + ED_3COM_PSTR, sc->rec_page_start); bus_space_write_1(iot, ioh, asicbase + ED_3COM_PSPR, sc->rec_page_stop); /* Set IRQ. 3c503 only allows a choice of irq 3-5 or 9. */ switch (ia->ia_irq) { case 9: bus_space_write_1(iot, ioh, asicbase + ED_3COM_IDCFR, ED_3COM_IDCFR_IRQ2); break; case 3: bus_space_write_1(iot, ioh, asicbase + ED_3COM_IDCFR, ED_3COM_IDCFR_IRQ3); break; case 4: bus_space_write_1(iot, ioh, asicbase + ED_3COM_IDCFR, ED_3COM_IDCFR_IRQ4); break; case 5: bus_space_write_1(iot, ioh, asicbase + ED_3COM_IDCFR, ED_3COM_IDCFR_IRQ5); break; default: printf("%s: invalid irq configuration (%d) must be 3-5 or 9 for 3c503\n", sc->sc_dev.dv_xname, ia->ia_irq); goto out; } /* * Initialize GA configuration register. Set bank and enable shared * mem. */ bus_space_write_1(iot, ioh, asicbase + ED_3COM_GACFR, ED_3COM_GACFR_RSEL | ED_3COM_GACFR_MBS0); /* * Initialize "Vector Pointer" registers. These gawd-awful things are * compared to 20 bits of the address on ISA, and if they match, the * shared memory is disabled. We set them to 0xffff0...allegedly the * reset vector. */ bus_space_write_1(iot, ioh, asicbase + ED_3COM_VPTR2, 0xff); bus_space_write_1(iot, ioh, asicbase + ED_3COM_VPTR1, 0xff); bus_space_write_1(iot, ioh, asicbase + ED_3COM_VPTR0, 0x00); /* Now zero memory and verify that it is clear. */ if (isa16bit) { for (i = 0; i < memsize; i += 2) bus_space_write_2(memt, memh, sc->mem_start + i, 0); } else { for (i = 0; i < memsize; ++i) bus_space_write_1(memt, memh, sc->mem_start + i, 0); } memfail = 0; if (isa16bit) { for (i = 0; i < memsize; i += 2) { if (bus_space_read_2(memt, memh, sc->mem_start + i)) { memfail = 1; break; } } } else { for (i = 0; i < memsize; ++i) { if (bus_space_read_1(memt, memh, sc->mem_start + i)) { memfail = 1; break; } } } if (memfail) { printf("%s: failed to clear shared memory at %x - " "check configuration\n", sc->sc_dev.dv_xname, (ia->ia_maddr + sc->mem_start + i)); goto out; } ia->ia_msize = memsize; ia->ia_iosize = ED_3COM_IO_PORTS; /* * XXX Sould always unmap, but we can't yet. * XXX Need to squish "indirect" first. */ sc->sc_iot = iot; sc->sc_memt = memt; sc->sc_ioh = ioh; sc->sc_memh = memh; return 1; out: bus_space_unmap(memt, memh, memsize); err: bus_space_unmap(iot, ioh, ED_3COM_IO_PORTS); return 0; } /* * Probe and vendor-specific initialization routine for NE1000/2000 boards. */ int ed_find_Novell(sc, cf, ia) struct ed_softc *sc; struct cfdata *cf; struct isa_attach_args *ia; { bus_space_tag_t iot; bus_space_handle_t ioh; u_int memsize, n; u_char romdata[16], tmp; static u_char test_pattern[32] = "THIS is A memory TEST pattern"; u_char test_buffer[32]; int asicbase, nicbase; iot = ia->ia_iot; if (bus_space_map(iot, ia->ia_iobase, ED_NOVELL_IO_PORTS, 0, &ioh)) return (0); sc->asic_base = asicbase = ED_NOVELL_ASIC_OFFSET; sc->nic_base = nicbase = ED_NOVELL_NIC_OFFSET; /* XXX - do Novell-specific probe here */ /* Reset the board. */ #ifdef GWETHER bus_space_write_1(iot, ioh, asicbase + ED_NOVELL_RESET, 0); delay(200); #endif /* GWETHER */ tmp = bus_space_read_1(iot, ioh, asicbase + ED_NOVELL_RESET); /* * I don't know if this is necessary; probably cruft leftover from * Clarkson packet driver code. Doesn't do a thing on the boards I've * tested. -DG [note that a outb(0x84, 0) seems to work here, and is * non-invasive...but some boards don't seem to reset and I don't have * complete documentation on what the 'right' thing to do is...so we do * the invasive thing for now. Yuck.] */ bus_space_write_1(iot, ioh, asicbase + ED_NOVELL_RESET, tmp); delay(5000); /* * This is needed because some NE clones apparently don't reset the NIC * properly (or the NIC chip doesn't reset fully on power-up) * XXX - this makes the probe invasive! ...Done against my better * judgement. -DLG */ NIC_PUT(iot, ioh, nicbase, ED_P0_CR, ED_CR_RD2 | ED_CR_PAGE_0 | ED_CR_STP); delay(5000); /* Make sure that we really have an 8390 based board. */ if (!ed_probe_generic8390(iot, ioh, nicbase)) goto out; sc->vendor = ED_VENDOR_NOVELL; sc->mem_shared = 0; sc->cr_proto = ED_CR_RD2; ia->ia_msize = 0; /* * Test the ability to read and write to the NIC memory. This has the * side affect of determining if this is an NE1000 or an NE2000. */ /* * This prevents packets from being stored in the NIC memory when the * readmem routine turns on the start bit in the CR. */ NIC_PUT(iot, ioh, nicbase, ED_P0_RCR, ED_RCR_MON); /* Temporarily initialize DCR for byte operations. */ NIC_PUT(iot, ioh, nicbase, ED_P0_DCR, ED_DCR_FT1 | ED_DCR_LS); NIC_PUT(iot, ioh, nicbase, ED_P0_PSTART, 8192 >> ED_PAGE_SHIFT); NIC_PUT(iot, ioh, nicbase, ED_P0_PSTOP, 16384 >> ED_PAGE_SHIFT); sc->isa16bit = 0; /* * XXX indirect brokenness, used by ed_pio{read,write}mem() */ sc->sc_iot = iot; sc->sc_ioh = ioh; /* * Write a test pattern in byte mode. If this fails, then there * probably isn't any memory at 8k - which likely means that the board * is an NE2000. */ ed_pio_writemem(sc, test_pattern, 8192, sizeof(test_pattern)); ed_pio_readmem(sc, 8192, test_buffer, sizeof(test_pattern)); if (bcmp(test_pattern, test_buffer, sizeof(test_pattern))) { /* not an NE1000 - try NE2000 */ NIC_PUT(iot, ioh, nicbase, ED_P0_DCR, ED_DCR_WTS | ED_DCR_FT1 | ED_DCR_LS); NIC_PUT(iot, ioh, nicbase, ED_P0_PSTART, 16384 >> ED_PAGE_SHIFT); NIC_PUT(iot, ioh, nicbase, ED_P0_PSTOP, 32768 >> ED_PAGE_SHIFT); sc->isa16bit = 1; /* * Write a test pattern in word mode. If this also fails, then * we don't know what this board is. */ ed_pio_writemem(sc, test_pattern, 16384, sizeof(test_pattern)); ed_pio_readmem(sc, 16384, test_buffer, sizeof(test_pattern)); if (bcmp(test_pattern, test_buffer, sizeof(test_pattern))) goto out; /* not an NE2000 either */ sc->type = ED_TYPE_NE2000; sc->type_str = "NE2000"; } else { sc->type = ED_TYPE_NE1000; sc->type_str = "NE1000"; } if (ia->ia_irq == IRQUNK) { printf("%s: %s does not have soft configuration\n", sc->sc_dev.dv_xname, sc->type_str); goto out; } /* 8k of memory plus an additional 8k if 16-bit. */ memsize = 8192 + sc->isa16bit * 8192; #if 0 /* probably not useful - NE boards only come two ways */ /* Allow kernel config file overrides. */ if (ia->ia_msize) memsize = ia->ia_msize; #endif /* NIC memory doesn't start at zero on an NE board. */ /* The start address is tied to the bus width. */ sc->mem_start = (8192 + sc->isa16bit * 8192); sc->tx_page_start = memsize >> ED_PAGE_SHIFT; #ifdef GWETHER { int x, i, mstart = 0; char pbuf0[ED_PAGE_SIZE], pbuf[ED_PAGE_SIZE], tbuf[ED_PAGE_SIZE]; for (i = 0; i < ED_PAGE_SIZE; i++) pbuf0[i] = 0; /* Search for the start of RAM. */ for (x = 1; x < 256; x++) { ed_pio_writemem(sc, pbuf0, x << ED_PAGE_SHIFT, ED_PAGE_SIZE); ed_pio_readmem(sc, x << ED_PAGE_SHIFT, tbuf, ED_PAGE_SIZE); if (!bcmp(pbuf0, tbuf, ED_PAGE_SIZE)) { for (i = 0; i < ED_PAGE_SIZE; i++) pbuf[i] = 255 - x; ed_pio_writemem(sc, pbuf, x << ED_PAGE_SHIFT, ED_PAGE_SIZE); ed_pio_readmem(sc, x << ED_PAGE_SHIFT, tbuf, ED_PAGE_SIZE); if (!bcmp(pbuf, tbuf, ED_PAGE_SIZE)) { mstart = x << ED_PAGE_SHIFT; memsize = ED_PAGE_SIZE; break; } } } if (mstart == 0) { printf("%s: cannot find start of RAM\n", sc->sc_dev.dv_xname); goto err; } /* Search for the end of RAM. */ for (++x; x < 256; x++) { ed_pio_writemem(sc, pbuf0, x << ED_PAGE_SHIFT, ED_PAGE_SIZE); ed_pio_readmem(sc, x << ED_PAGE_SHIFT, tbuf, ED_PAGE_SIZE); if (!bcmp(pbuf0, tbuf, ED_PAGE_SIZE)) { for (i = 0; i < ED_PAGE_SIZE; i++) pbuf[i] = 255 - x; ed_pio_writemem(sc, pbuf, x << ED_PAGE_SHIFT, ED_PAGE_SIZE); ed_pio_readmem(sc, x << ED_PAGE_SHIFT, tbuf, ED_PAGE_SIZE); if (!bcmp(pbuf, tbuf, ED_PAGE_SIZE)) memsize += ED_PAGE_SIZE; else break; } else break; } printf("%s: RAM start %x, size %d\n", sc->sc_dev.dv_xname, mstart, memsize); sc->mem_start = (caddr_t)mstart; sc->tx_page_start = mstart >> ED_PAGE_SHIFT; } #endif /* GWETHER */ sc->mem_size = memsize; sc->mem_end = sc->mem_start + memsize; /* * Use one xmit buffer if < 16k, two buffers otherwise (if not told * otherwise). */ if ((memsize < 16384) || (cf->cf_flags & ED_FLAGS_NO_MULTI_BUFFERING)) sc->txb_cnt = 1; else sc->txb_cnt = 2; sc->rec_page_start = sc->tx_page_start + sc->txb_cnt * ED_TXBUF_SIZE; sc->rec_page_stop = sc->tx_page_start + (memsize >> ED_PAGE_SHIFT); sc->mem_ring = sc->mem_start + ((sc->txb_cnt * ED_TXBUF_SIZE) << ED_PAGE_SHIFT); ed_pio_readmem(sc, 0, romdata, 16); for (n = 0; n < ETHER_ADDR_LEN; n++) sc->sc_arpcom.ac_enaddr[n] = romdata[n*(sc->isa16bit+1)]; #ifdef GWETHER if (sc->arpcom.ac_enaddr[2] == 0x86) sc->type_str = "Gateway AT"; #endif /* GWETHER */ /* Clear any pending interrupts that might have occurred above. */ NIC_PUT(iot, ioh, nicbase, ED_P0_ISR, 0xff); ia->ia_iosize = ED_NOVELL_IO_PORTS; /* * XXX Sould always unmap, but we can't yet. * XXX Need to squish "indirect" first. */ sc->sc_iot = iot; sc->sc_ioh = ioh; /* sc_memh is not used by this driver */ return 1; out: bus_space_unmap(iot, ioh, ED_NOVELL_IO_PORTS); return 0; } /* * Install interface into kernel networking data structures. */ void edattach(parent, self, aux) struct device *parent, *self; void *aux; { bus_space_tag_t iot; bus_space_handle_t ioh; struct ed_softc *sc = (void *)self; struct isa_attach_args *ia = aux; struct cfdata *cf = sc->sc_dev.dv_cfdata; struct ifnet *ifp = &sc->sc_arpcom.ac_if; int asicbase; /* * XXX Should re-map io and mem, but can't * XXX until we squish "indirect" brokenness. */ iot = sc->sc_iot; /* XXX */ ioh = sc->sc_ioh; /* XXX */ asicbase = sc->asic_base; sc->sc_delaybah = ia->ia_delaybah; /* Set interface to stopped condition (reset). */ edstop(sc); /* Initialize ifnet structure. */ bcopy(sc->sc_dev.dv_xname, ifp->if_xname, IFNAMSIZ); ifp->if_softc = sc; ifp->if_start = edstart; ifp->if_ioctl = edioctl; ifp->if_watchdog = edwatchdog; ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_NOTRAILERS | IFF_MULTICAST; /* * Set default state for LINK0 flag (used to disable the tranceiver * for AUI operation), based on compile-time config option. */ switch (sc->vendor) { case ED_VENDOR_3COM: if (cf->cf_flags & ED_FLAGS_DISABLE_TRANCEIVER) ifp->if_flags |= IFF_LINK0; break; case ED_VENDOR_WD_SMC: if ((sc->type & ED_WD_SOFTCONFIG) == 0) break; if ((bus_space_read_1(iot, ioh, asicbase + ED_WD_IRR) & ED_WD_IRR_OUT2) == 0) ifp->if_flags |= IFF_LINK0; break; } /* Attach the interface. */ if ((sc->spec_flags & ED_REATTACH) == 0) { if_attach(ifp); ether_ifattach(ifp); } ether_ifattach(ifp); /* Print additional info when attached. */ printf("\n%s: address %s, ", sc->sc_dev.dv_xname, ether_sprintf(sc->sc_arpcom.ac_enaddr)); if (sc->type_str) printf("type %s ", sc->type_str); else printf("type unknown (0x%x) ", sc->type); printf("%s", sc->isa16bit ? "(16-bit)" : "(8-bit)"); switch (sc->vendor) { case ED_VENDOR_WD_SMC: if ((sc->type & ED_WD_SOFTCONFIG) == 0) break; case ED_VENDOR_3COM: if (ifp->if_flags & IFF_LINK0) printf(" aui"); else printf(" bnc"); break; } printf("\n"); #if NBPFILTER > 0 if ((sc->spec_flags & ED_REATTACH) == 0) bpfattach(&ifp->if_bpf, ifp, DLT_EN10MB, sizeof(struct ether_header)); #endif sc->sc_ih = isa_intr_establish(ia->ia_ic, ia->ia_irq, IST_EDGE, IPL_NET, edintr, sc, sc->sc_dev.dv_xname); sc->sc_sh = shutdownhook_establish((void (*)(void *))edstop, sc); } /* * Reset interface. */ void edreset(sc) struct ed_softc *sc; { int s; s = splnet(); edstop(sc); edinit(sc); splx(s); } /* * Take interface offline. */ void edstop(sc) struct ed_softc *sc; { bus_space_tag_t iot = sc->sc_iot; bus_space_handle_t ioh = sc->sc_ioh; int nicbase = sc->nic_base; int n = 5000; /* Stop everything on the interface, and select page 0 registers. */ NIC_PUT(iot, ioh, nicbase, ED_P0_CR, sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STP); /* * Wait for interface to enter stopped state, but limit # of checks to * 'n' (about 5ms). It shouldn't even take 5us on modern DS8390's, but * just in case it's an old one. */ while (((NIC_GET(iot, ioh, nicbase, ED_P0_ISR) & ED_ISR_RST) == 0) && --n); } /* * Device timeout/watchdog routine. Entered if the device neglects to generate * an interrupt after a transmit has been started on it. */ void edwatchdog(ifp) struct ifnet *ifp; { struct ed_softc *sc = ifp->if_softc; log(LOG_ERR, "%s: device timeout\n", sc->sc_dev.dv_xname); ++sc->sc_arpcom.ac_if.if_oerrors; edreset(sc); } /* * Initialize device. */ void edinit(sc) struct ed_softc *sc; { bus_space_tag_t iot = sc->sc_iot; bus_space_handle_t ioh = sc->sc_ioh; struct ifnet *ifp = &sc->sc_arpcom.ac_if; int nicbase = sc->nic_base, asicbase = sc->asic_base; int i; u_long mcaf[2]; /* * Initialize the NIC in the exact order outlined in the NS manual. * This init procedure is "mandatory"...don't change what or when * things happen. */ /* Reset transmitter flags. */ ifp->if_timer = 0; sc->txb_inuse = 0; sc->txb_new = 0; sc->txb_next_tx = 0; /* Set interface for page 0, remote DMA complete, stopped. */ NIC_PUT(iot, ioh, nicbase, ED_P0_CR, sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STP); if (sc->isa16bit) { /* * Set FIFO threshold to 8, No auto-init Remote DMA, byte * order=80x86, word-wide DMA xfers, */ NIC_PUT(iot, ioh, nicbase, ED_P0_DCR, ED_DCR_FT1 | ED_DCR_WTS | ED_DCR_LS); } else { /* Same as above, but byte-wide DMA xfers. */ NIC_PUT(iot, ioh, nicbase, ED_P0_DCR, ED_DCR_FT1 | ED_DCR_LS); } /* Clear remote byte count registers. */ NIC_PUT(iot, ioh, nicbase, ED_P0_RBCR0, 0); NIC_PUT(iot, ioh, nicbase, ED_P0_RBCR1, 0); /* Tell RCR to do nothing for now. */ NIC_PUT(iot, ioh, nicbase, ED_P0_RCR, ED_RCR_MON); /* Place NIC in internal loopback mode. */ NIC_PUT(iot, ioh, nicbase, ED_P0_TCR, ED_TCR_LB0); /* Set lower bits of byte addressable framing to 0. */ if (sc->is790) NIC_PUT(iot, ioh, nicbase, 0x09, 0); /* Initialize receive buffer ring. */ NIC_PUT(iot, ioh, nicbase, ED_P0_BNRY, sc->rec_page_start); NIC_PUT(iot, ioh, nicbase, ED_P0_PSTART, sc->rec_page_start); NIC_PUT(iot, ioh, nicbase, ED_P0_PSTOP, sc->rec_page_stop); /* * Clear all interrupts. A '1' in each bit position clears the * corresponding flag. */ NIC_PUT(iot, ioh, nicbase, ED_P0_ISR, 0xff); /* * Enable the following interrupts: receive/transmit complete, * receive/transmit error, and Receiver OverWrite. * * Counter overflow and Remote DMA complete are *not* enabled. */ NIC_PUT(iot, ioh, nicbase, ED_P0_IMR, ED_IMR_PRXE | ED_IMR_PTXE | ED_IMR_RXEE | ED_IMR_TXEE | ED_IMR_OVWE); /* Program command register for page 1. */ NIC_PUT(iot, ioh, nicbase, ED_P0_CR, sc->cr_proto | ED_CR_PAGE_1 | ED_CR_STP); /* Copy out our station address. */ for (i = 0; i < ETHER_ADDR_LEN; ++i) NIC_PUT(iot, ioh, nicbase, ED_P1_PAR0 + i, sc->sc_arpcom.ac_enaddr[i]); /* Set multicast filter on chip. */ ed_getmcaf(&sc->sc_arpcom, mcaf); for (i = 0; i < 8; i++) NIC_PUT(iot, ioh, nicbase, ED_P1_MAR0 + i, ((u_char *)mcaf)[i]); /* * Set current page pointer to one page after the boundary pointer, as * recommended in the National manual. */ sc->next_packet = sc->rec_page_start + 1; NIC_PUT(iot, ioh, nicbase, ED_P1_CURR, sc->next_packet); /* Program command register for page 0. */ NIC_PUT(iot, ioh, nicbase, ED_P1_CR, sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STP); i = ED_RCR_AB | ED_RCR_AM; if (ifp->if_flags & IFF_PROMISC) { /* * Set promiscuous mode. Multicast filter was set earlier so * that we should receive all multicast packets. */ i |= ED_RCR_PRO | ED_RCR_AR | ED_RCR_SEP; } NIC_PUT(iot, ioh, nicbase, ED_P0_RCR, i); /* Take interface out of loopback. */ NIC_PUT(iot, ioh, nicbase, ED_P0_TCR, 0); /* * If this is a 3Com board, the tranceiver must be software enabled * (there is no settable hardware default). */ switch (sc->vendor) { u_char x; case ED_VENDOR_3COM: if (ifp->if_flags & IFF_LINK0) bus_space_write_1(iot, ioh, asicbase + ED_3COM_CR, 0); else bus_space_write_1(iot, ioh, asicbase + ED_3COM_CR, ED_3COM_CR_XSEL); break; case ED_VENDOR_WD_SMC: if ((sc->type & ED_WD_SOFTCONFIG) == 0) break; x = bus_space_read_1(iot, ioh, asicbase + ED_WD_IRR); if (ifp->if_flags & IFF_LINK0) x &= ~ED_WD_IRR_OUT2; else x |= ED_WD_IRR_OUT2; bus_space_write_1(iot, ioh, asicbase + ED_WD_IRR, x); break; } /* Fire up the interface. */ NIC_PUT(iot, ioh, nicbase, ED_P0_CR, sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STA); /* Set 'running' flag, and clear output active flag. */ ifp->if_flags |= IFF_RUNNING; ifp->if_flags &= ~IFF_OACTIVE; /* ...and attempt to start output. */ edstart(ifp); } /* * This routine actually starts the transmission on the interface. */ static __inline void ed_xmit(sc) struct ed_softc *sc; { bus_space_tag_t iot = sc->sc_iot; bus_space_handle_t ioh = sc->sc_ioh; struct ifnet *ifp = &sc->sc_arpcom.ac_if; int nicbase = sc->nic_base; u_short len; len = sc->txb_len[sc->txb_next_tx]; /* Set NIC for page 0 register access. */ NIC_PUT(iot, ioh, nicbase, ED_P0_CR, sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STA); /* Set TX buffer start page. */ NIC_PUT(iot, ioh, nicbase, ED_P0_TPSR, sc->tx_page_start + sc->txb_next_tx * ED_TXBUF_SIZE); /* Set TX length. */ NIC_PUT(iot, ioh, nicbase, ED_P0_TBCR0, len); NIC_PUT(iot, ioh, nicbase, ED_P0_TBCR1, len >> 8); /* Set page 0, remote DMA complete, transmit packet, and *start*. */ NIC_PUT(iot, ioh, nicbase, ED_P0_CR, sc->cr_proto | ED_CR_PAGE_0 | ED_CR_TXP | ED_CR_STA); /* Point to next transmit buffer slot and wrap if necessary. */ sc->txb_next_tx++; if (sc->txb_next_tx == sc->txb_cnt) sc->txb_next_tx = 0; /* Set a timer just in case we never hear from the board again. */ ifp->if_timer = 2; } /* * Start output on interface. * We make two assumptions here: * 1) that the current priority is set to splnet _before_ this code * is called *and* is returned to the appropriate priority after * return * 2) that the IFF_OACTIVE flag is checked before this code is called * (i.e. that the output part of the interface is idle) */ void edstart(ifp) struct ifnet *ifp; { struct ed_softc *sc = ifp->if_softc; bus_space_tag_t iot = sc->sc_iot; bus_space_handle_t ioh = sc->sc_ioh; struct mbuf *m0, *m; int buffer; int asicbase = sc->asic_base; int len; if ((ifp->if_flags & (IFF_RUNNING | IFF_OACTIVE)) != IFF_RUNNING) return; outloop: /* See if there is room to put another packet in the buffer. */ if (sc->txb_inuse == sc->txb_cnt) { /* No room. Indicate this to the outside world and exit. */ ifp->if_flags |= IFF_OACTIVE; return; } IF_DEQUEUE(&ifp->if_snd, m0); if (m0 == 0) return; /* We need to use m->m_pkthdr.len, so require the header */ if ((m0->m_flags & M_PKTHDR) == 0) panic("edstart: no header mbuf"); #if NBPFILTER > 0 /* Tap off here if there is a BPF listener. */ if (ifp->if_bpf) bpf_mtap(ifp->if_bpf, m0); #endif /* txb_new points to next open buffer slot. */ buffer = sc->mem_start + ((sc->txb_new * ED_TXBUF_SIZE) << ED_PAGE_SHIFT); if (sc->mem_shared) { /* Special case setup for 16 bit boards... */ switch (sc->vendor) { /* * For 16bit 3Com boards (which have 16k of memory), we * have the xmit buffers in a different page of memory * ('page 0') - so change pages. */ case ED_VENDOR_3COM: if (sc->isa16bit) bus_space_write_1(iot, ioh, asicbase + ED_3COM_GACFR, ED_3COM_GACFR_RSEL); break; /* * Enable 16bit access to shared memory on WD/SMC * boards. */ case ED_VENDOR_WD_SMC: if (sc->isa16bit) bus_space_write_1(iot, ioh, asicbase + ED_WD_LAAR, sc->wd_laar_proto | ED_WD_LAAR_M16EN); bus_space_write_1(iot, ioh, asicbase + ED_WD_MSR, sc->wd_msr_proto | ED_WD_MSR_MENB); (void) bus_space_read_1(iot, sc->sc_delaybah, 0); (void) bus_space_read_1(iot, sc->sc_delaybah, 0); break; } for (m = m0; m != 0; m = m->m_next) { ed_shared_writemem(sc, mtod(m, caddr_t), buffer, m->m_len); buffer += m->m_len; } len = m0->m_pkthdr.len; /* Restore previous shared memory access. */ switch (sc->vendor) { case ED_VENDOR_3COM: if (sc->isa16bit) bus_space_write_1(iot, ioh, asicbase + ED_3COM_GACFR, ED_3COM_GACFR_RSEL | ED_3COM_GACFR_MBS0); break; case ED_VENDOR_WD_SMC: bus_space_write_1(iot, ioh, asicbase + ED_WD_MSR, sc->wd_msr_proto); if (sc->isa16bit) bus_space_write_1(iot, ioh, asicbase + ED_WD_LAAR, sc->wd_laar_proto); (void) bus_space_read_1(iot, sc->sc_delaybah, 0); (void) bus_space_read_1(iot, sc->sc_delaybah, 0); break; } } else len = ed_pio_write_mbufs(sc, m0, (long)buffer); m_freem(m0); sc->txb_len[sc->txb_new] = max(len, ETHER_MIN_LEN); /* Start the first packet transmitting. */ if (sc->txb_inuse == 0) ed_xmit(sc); /* Point to next buffer slot and wrap if necessary. */ if (++sc->txb_new == sc->txb_cnt) sc->txb_new = 0; sc->txb_inuse++; /* Loop back to the top to possibly buffer more packets. */ goto outloop; } /* * Ethernet interface receiver interrupt. */ static __inline void ed_rint(sc) struct ed_softc *sc; { bus_space_tag_t iot = sc->sc_iot; bus_space_handle_t ioh = sc->sc_ioh; int nicbase = sc->nic_base; u_int8_t boundary, current; u_int16_t len; u_int8_t nlen; u_int8_t next_packet; /* pointer to next packet */ u_int8_t rsr; /* receiver status */ u_int16_t count; /* bytes in packet (length + 4) */ u_int8_t packet_hdr[ED_RING_HDRSZ]; int packet_ptr; loop: /* Set NIC to page 1 registers to get 'current' pointer. */ NIC_PUT(iot, ioh, nicbase, ED_P0_CR, sc->cr_proto | ED_CR_PAGE_1 | ED_CR_STA); /* * 'sc->next_packet' is the logical beginning of the ring-buffer - i.e. * it points to where new data has been buffered. The 'CURR' (current) * register points to the logical end of the ring-buffer - i.e. it * points to where additional new data will be added. We loop here * until the logical beginning equals the logical end (or in other * words, until the ring-buffer is empty). */ current = NIC_GET(iot, ioh, nicbase, ED_P1_CURR); if (sc->next_packet == current) return; /* Set NIC to page 0 registers to update boundary register. */ NIC_PUT(iot, ioh, nicbase, ED_P1_CR, sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STA); do { /* Get pointer to this buffer's header structure. */ packet_ptr = sc->mem_ring + ((sc->next_packet - sc->rec_page_start) << ED_PAGE_SHIFT); /* * The byte count includes a 4 byte header that was added by * the NIC. */ if (sc->mem_shared) ed_shared_readmem(sc, packet_ptr, packet_hdr, sizeof(packet_hdr)); else ed_pio_readmem(sc, (long)packet_ptr, packet_hdr, sizeof(packet_hdr)); rsr = packet_hdr[ED_RING_RSR]; next_packet = packet_hdr[ED_RING_NEXT_PACKET]; len = count = packet_hdr[ED_RING_COUNT] + 256 * packet_hdr[ED_RING_COUNT + 1]; /* * Try do deal with old, buggy chips that sometimes duplicate * the low byte of the length into the high byte. We do this * by simply ignoring the high byte of the length and always * recalculating it. * * NOTE: sc->next_packet is pointing at the current packet. */ if (next_packet >= sc->next_packet) nlen = (next_packet - sc->next_packet); else nlen = ((next_packet - sc->rec_page_start) + (sc->rec_page_stop - sc->next_packet)); --nlen; if ((len & ED_PAGE_MASK) + sizeof(packet_hdr) > ED_PAGE_SIZE) --nlen; len = (len & ED_PAGE_MASK) | (nlen << ED_PAGE_SHIFT); #ifdef DIAGNOSTIC if (len != count) { printf("%s: length does not match next packet pointer\n", sc->sc_dev.dv_xname); printf("%s: len %04x nlen %04x start %02x first %02x curr %02x next %02x stop %02x\n", sc->sc_dev.dv_xname, count, len, sc->rec_page_start, sc->next_packet, current, next_packet, sc->rec_page_stop); } #endif /* * Be fairly liberal about what we allow as a "reasonable" * length so that a [crufty] packet will make it to BPF (and * can thus be analyzed). Note that all that is really * important is that we have a length that will fit into one * mbuf cluster or less; the upper layer protocols can then * figure out the length from their own length field(s). */ if (len <= MCLBYTES && next_packet >= sc->rec_page_start && next_packet < sc->rec_page_stop) { /* Go get packet. */ edread(sc, packet_ptr + ED_RING_HDRSZ, len - ED_RING_HDRSZ); } else { /* Really BAD. The ring pointers are corrupted. */ log(LOG_ERR, "%s: NIC memory corrupt - invalid packet length %d\n", sc->sc_dev.dv_xname, len); ++sc->sc_arpcom.ac_if.if_ierrors; edreset(sc); return; } /* Update next packet pointer. */ sc->next_packet = next_packet; /* * Update NIC boundary pointer - being careful to keep it one * buffer behind (as recommended by NS databook). */ boundary = sc->next_packet - 1; if (boundary < sc->rec_page_start) boundary = sc->rec_page_stop - 1; NIC_PUT(iot, ioh, nicbase, ED_P0_BNRY, boundary); } while (sc->next_packet != current); goto loop; } /* Ethernet interface interrupt processor. */ int edintr(arg) void *arg; { struct ed_softc *sc = arg; bus_space_tag_t iot = sc->sc_iot; bus_space_handle_t ioh = sc->sc_ioh; struct ifnet *ifp = &sc->sc_arpcom.ac_if; int nicbase = sc->nic_base, asicbase = sc->asic_base; u_char isr; /* Set NIC to page 0 registers. */ NIC_PUT(iot, ioh, nicbase, ED_P0_CR, sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STA); isr = NIC_GET(iot, ioh, nicbase, ED_P0_ISR); if (!isr) return (0); /* Loop until there are no more new interrupts. */ for (;;) { /* * Reset all the bits that we are 'acknowledging' by writing a * '1' to each bit position that was set. * (Writing a '1' *clears* the bit.) */ NIC_PUT(iot, ioh, nicbase, ED_P0_ISR, isr); /* * Handle transmitter interrupts. Handle these first because * the receiver will reset the board under some conditions. */ if (isr & (ED_ISR_PTX | ED_ISR_TXE)) { u_char collisions = NIC_GET(iot, ioh, nicbase, ED_P0_NCR) & 0x0f; /* * Check for transmit error. If a TX completed with an * error, we end up throwing the packet away. Really * the only error that is possible is excessive * collisions, and in this case it is best to allow the * automatic mechanisms of TCP to backoff the flow. Of * course, with UDP we're screwed, but this is expected * when a network is heavily loaded. */ (void) NIC_GET(iot, ioh, nicbase, ED_P0_TSR); if (isr & ED_ISR_TXE) { /* * Excessive collisions (16). */ if ((NIC_GET(iot, ioh, nicbase, ED_P0_TSR) & ED_TSR_ABT) && (collisions == 0)) { /* * When collisions total 16, the P0_NCR * will indicate 0, and the TSR_ABT is * set. */ collisions = 16; } /* Update output errors counter. */ ++ifp->if_oerrors; } else { /* * Update total number of successfully * transmitted packets. */ ++ifp->if_opackets; } /* Done with the buffer. */ sc->txb_inuse--; /* Clear watchdog timer. */ ifp->if_timer = 0; ifp->if_flags &= ~IFF_OACTIVE; /* * Add in total number of collisions on last * transmission. */ ifp->if_collisions += collisions; /* * Decrement buffer in-use count if not zero (can only * be zero if a transmitter interrupt occured while not * actually transmitting). * If data is ready to transmit, start it transmitting, * otherwise defer until after handling receiver. */ if (sc->txb_inuse > 0) ed_xmit(sc); } /* Handle receiver interrupts. */ if (isr & (ED_ISR_PRX | ED_ISR_RXE | ED_ISR_OVW)) { /* * Overwrite warning. In order to make sure that a * lockup of the local DMA hasn't occurred, we reset * and re-init the NIC. The NSC manual suggests only a * partial reset/re-init is necessary - but some chips * seem to want more. The DMA lockup has been seen * only with early rev chips - Methinks this bug was * fixed in later revs. -DG */ if (isr & ED_ISR_OVW) { ++ifp->if_ierrors; #ifdef DIAGNOSTIC log(LOG_WARNING, "%s: warning - receiver ring buffer overrun\n", sc->sc_dev.dv_xname); #endif /* Stop/reset/re-init NIC. */ edreset(sc); } else { /* * Receiver Error. One or more of: CRC error, * frame alignment error FIFO overrun, or * missed packet. */ if (isr & ED_ISR_RXE) { ++ifp->if_ierrors; #ifdef ED_DEBUG printf("%s: receive error %x\n", sc->sc_dev.dv_xname, NIC_GET(nicbase, ED_P0_RSR)); #endif } /* * Go get the packet(s). * XXX - Doing this on an error is dubious * because there shouldn't be any data to get * (we've configured the interface to not * accept packets with errors). */ /* * Enable 16bit access to shared memory first * on WD/SMC boards. */ if (sc->vendor == ED_VENDOR_WD_SMC) { if (sc->isa16bit) bus_space_write_1(iot, ioh, asicbase + ED_WD_LAAR, sc->wd_laar_proto | ED_WD_LAAR_M16EN); bus_space_write_1(iot, ioh, asicbase + ED_WD_MSR, sc->wd_msr_proto | ED_WD_MSR_MENB); (void) bus_space_read_1(iot, sc->sc_delaybah, 0); (void) bus_space_read_1(iot, sc->sc_delaybah, 0); } ed_rint(sc); /* Disable 16-bit access. */ if (sc->vendor == ED_VENDOR_WD_SMC) { bus_space_write_1(iot, ioh, asicbase + ED_WD_MSR, sc->wd_msr_proto); if (sc->isa16bit) bus_space_write_1(iot, ioh, asicbase + ED_WD_LAAR, sc->wd_laar_proto); (void) bus_space_read_1(iot, sc->sc_delaybah, 0); (void) bus_space_read_1(iot, sc->sc_delaybah, 0); } } } /* * If it looks like the transmitter can take more data, attempt * to start output on the interface. This is done after * handling the receiver to give the receiver priority. */ edstart(ifp); /* * Return NIC CR to standard state: page 0, remote DMA * complete, start (toggling the TXP bit off, even if was just * set in the transmit routine, is *okay* - it is 'edge' * triggered from low to high). */ NIC_PUT(iot, ioh, nicbase, ED_P0_CR, sc->cr_proto | ED_CR_PAGE_0 | ED_CR_STA); /* * If the Network Talley Counters overflow, read them to reset * them. It appears that old 8390's won't clear the ISR flag * otherwise - resulting in an infinite loop. */ if (isr & ED_ISR_CNT) { (void) NIC_GET(iot, ioh, nicbase, ED_P0_CNTR0); (void) NIC_GET(iot, ioh, nicbase, ED_P0_CNTR1); (void) NIC_GET(iot, ioh, nicbase, ED_P0_CNTR2); } isr = NIC_GET(iot, ioh, nicbase, ED_P0_ISR); if (!isr) return (1); } } /* * Process an ioctl request. This code needs some work - it looks pretty ugly. */ int edioctl(ifp, cmd, data) register struct ifnet *ifp; u_long cmd; caddr_t data; { struct ed_softc *sc = ifp->if_softc; register struct ifaddr *ifa = (struct ifaddr *)data; struct ifreq *ifr = (struct ifreq *)data; int s, error = 0; s = splnet(); if ((sc->spec_flags & ED_NOTPRESENT) != 0) { if_down(ifp); printf("%s: device offline\n", sc->sc_dev.dv_xname); splx(s); return ENXIO; /* may be ignored, oh well. */ } if ((error = ether_ioctl(ifp, &sc->sc_arpcom, cmd, data)) > 0) { splx(s); return error; } switch (cmd) { case SIOCSIFADDR: ifp->if_flags |= IFF_UP; switch (ifa->ifa_addr->sa_family) { #ifdef INET case AF_INET: edinit(sc); arp_ifinit(&sc->sc_arpcom, ifa); break; #endif default: edinit(sc); break; } break; case SIOCSIFFLAGS: if ((ifp->if_flags & IFF_UP) == 0 && (ifp->if_flags & IFF_RUNNING) != 0) { /* * If interface is marked down and it is running, then * stop it. */ edstop(sc); ifp->if_flags &= ~IFF_RUNNING; } else if ((ifp->if_flags & IFF_UP) != 0 && (ifp->if_flags & IFF_RUNNING) == 0) { /* * If interface is marked up and it is stopped, then * start it. */ edinit(sc); } else { /* * Reset the interface to pick up changes in any other * flags that affect hardware registers. */ edstop(sc); edinit(sc); } break; case SIOCADDMULTI: case SIOCDELMULTI: /* Update our multicast list. */ error = (cmd == SIOCADDMULTI) ? ether_addmulti(ifr, &sc->sc_arpcom) : ether_delmulti(ifr, &sc->sc_arpcom); if (error == ENETRESET) { /* * Multicast list has changed; set the hardware filter * accordingly. */ edstop(sc); /* XXX for ds_setmcaf? */ edinit(sc); error = 0; } break; default: error = EINVAL; break; } splx(s); return (error); } /* * Retreive packet from shared memory and send to the next level up via * ether_input(). If there is a BPF listener, give a copy to BPF, too. */ void edread(sc, buf, len) struct ed_softc *sc; int buf, len; { struct ifnet *ifp = &sc->sc_arpcom.ac_if; struct mbuf *m; struct ether_header *eh; /* Pull packet off interface. */ m = edget(sc, buf, len); if (m == 0) { ifp->if_ierrors++; return; } ifp->if_ipackets++; /* We assume that the header fit entirely in one mbuf. */ eh = mtod(m, struct ether_header *); #if NBPFILTER > 0 /* * Check if there's a BPF listener on this interface. * If so, hand off the raw packet to BPF. */ if (ifp->if_bpf) { bpf_mtap(ifp->if_bpf, m); /* * Note that the interface cannot be in promiscuous mode if * there are no BPF listeners. And if we are in promiscuous * mode, we have to check if this packet is really ours. */ if ((ifp->if_flags & IFF_PROMISC) && (eh->ether_dhost[0] & 1) == 0 && /* !mcast and !bcast */ bcmp(eh->ether_dhost, sc->sc_arpcom.ac_enaddr, sizeof(eh->ether_dhost)) != 0) { m_freem(m); return; } } #endif /* We assume that the header fit entirely in one mbuf. */ m_adj(m, sizeof(struct ether_header)); ether_input(ifp, eh, m); } /* * Supporting routines. */ /* * Given a NIC memory source address and a host memory destination address, * copy 'amount' from NIC to host using Programmed I/O. The 'amount' is * rounded up to a word - okay as long as mbufs are word sized. * This routine is currently Novell-specific. */ void ed_pio_readmem(sc, src, dst, amount) struct ed_softc *sc; u_short src; caddr_t dst; u_short amount; { bus_space_tag_t iot = sc->sc_iot; bus_space_handle_t ioh = sc->sc_ioh; int nicbase = sc->nic_base; /* Select page 0 registers. */ NIC_PUT(iot, ioh, nicbase, ED_P0_CR, ED_CR_RD2 | ED_CR_PAGE_0 | ED_CR_STA); /* Round up to a word. */ if (amount & 1) ++amount; /* Set up DMA byte count. */ NIC_PUT(iot, ioh, nicbase, ED_P0_RBCR0, amount); NIC_PUT(iot, ioh, nicbase, ED_P0_RBCR1, amount >> 8); /* Set up source address in NIC mem. */ NIC_PUT(iot, ioh, nicbase, ED_P0_RSAR0, src); NIC_PUT(iot, ioh, nicbase, ED_P0_RSAR1, src >> 8); NIC_PUT(iot, ioh, nicbase, ED_P0_CR, ED_CR_RD0 | ED_CR_PAGE_0 | ED_CR_STA); if (sc->isa16bit) bus_space_read_raw_multi_2(iot, ioh, sc->asic_base + ED_NOVELL_DATA, dst, amount); else bus_space_read_multi_1(iot, ioh, sc->asic_base + ED_NOVELL_DATA, dst, amount); } /* * Stripped down routine for writing a linear buffer to NIC memory. Only used * in the probe routine to test the memory. 'len' must be even. */ void ed_pio_writemem(sc, src, dst, len) struct ed_softc *sc; caddr_t src; u_short dst; u_short len; { bus_space_tag_t iot = sc->sc_iot; bus_space_handle_t ioh = sc->sc_ioh; int nicbase = sc->nic_base; int maxwait = 100; /* about 120us */ /* Select page 0 registers. */ NIC_PUT(iot, ioh, nicbase, ED_P0_CR, ED_CR_RD2 | ED_CR_PAGE_0 | ED_CR_STA); /* Reset remote DMA complete flag. */ NIC_PUT(iot, ioh, nicbase, ED_P0_ISR, ED_ISR_RDC); /* Set up DMA byte count. */ NIC_PUT(iot, ioh, nicbase, ED_P0_RBCR0, len); NIC_PUT(iot, ioh, nicbase, ED_P0_RBCR1, len >> 8); /* Set up destination address in NIC mem. */ NIC_PUT(iot, ioh, nicbase, ED_P0_RSAR0, dst); NIC_PUT(iot, ioh, nicbase, ED_P0_RSAR1, dst >> 8); /* Set remote DMA write. */ NIC_PUT(iot, ioh, nicbase, ED_P0_CR, ED_CR_RD1 | ED_CR_PAGE_0 | ED_CR_STA); if (sc->isa16bit) bus_space_write_raw_multi_2(iot, ioh, sc->asic_base + ED_NOVELL_DATA, src, len); else bus_space_write_multi_1(iot, ioh, sc->asic_base + ED_NOVELL_DATA, src, len); /* * Wait for remote DMA complete. This is necessary because on the * transmit side, data is handled internally by the NIC in bursts and * we can't start another remote DMA until this one completes. Not * waiting causes really bad things to happen - like the NIC * irrecoverably jamming the ISA bus. */ while (((NIC_GET(iot, ioh, nicbase, ED_P0_ISR) & ED_ISR_RDC) != ED_ISR_RDC) && --maxwait); } /* * Write an mbuf chain to the destination NIC memory address using programmed * I/O. */ u_short ed_pio_write_mbufs(sc, m, dst) struct ed_softc *sc; struct mbuf *m; u_short dst; { bus_space_tag_t iot = sc->sc_iot; bus_space_handle_t ioh = sc->sc_ioh; int nicbase = sc->nic_base, asicbase = sc->asic_base; u_short len; int maxwait = 100; /* about 120us */ len = m->m_pkthdr.len; /* Select page 0 registers. */ NIC_PUT(iot, ioh, nicbase, ED_P0_CR, ED_CR_RD2 | ED_CR_PAGE_0 | ED_CR_STA); /* Reset remote DMA complete flag. */ NIC_PUT(iot, ioh, nicbase, ED_P0_ISR, ED_ISR_RDC); /* Set up DMA byte count. */ NIC_PUT(iot, ioh, nicbase, ED_P0_RBCR0, len); NIC_PUT(iot, ioh, nicbase, ED_P0_RBCR1, len >> 8); /* Set up destination address in NIC mem. */ NIC_PUT(iot, ioh, nicbase, ED_P0_RSAR0, dst); NIC_PUT(iot, ioh, nicbase, ED_P0_RSAR1, dst >> 8); /* Set remote DMA write. */ NIC_PUT(iot, ioh, nicbase, ED_P0_CR, ED_CR_RD1 | ED_CR_PAGE_0 | ED_CR_STA); /* * Transfer the mbuf chain to the NIC memory. * 16-bit cards require that data be transferred as words, and only * words, so that case requires some extra code to patch over * odd-length mbufs. */ if (!sc->isa16bit) { /* NE1000s are easy. */ for (; m != 0; m = m->m_next) { if (m->m_len) { bus_space_write_multi_1(iot, ioh, asicbase + ED_NOVELL_DATA, mtod(m, u_char *), m->m_len); } } } else { /* NE2000s are a bit trickier. */ u_int8_t *data, savebyte[2]; int len, wantbyte; wantbyte = 0; for (; m != 0; m = m->m_next) { len = m->m_len; if (len == 0) continue; data = mtod(m, u_int8_t *); /* Finish the last word. */ if (wantbyte) { savebyte[1] = *data; bus_space_write_raw_multi_2(iot, ioh, asicbase + ED_NOVELL_DATA, savebyte, 2); data++; len--; wantbyte = 0; } /* Output contiguous words. */ if (len > 1) { bus_space_write_raw_multi_2(iot, ioh, asicbase + ED_NOVELL_DATA, data, len & ~1); } /* Save last byte, if necessary. */ if (len & 1) { data += len & ~1; savebyte[0] = *data; wantbyte = 1; } } if (wantbyte) { savebyte[1] = 0; bus_space_write_raw_multi_2(iot, ioh, asicbase + ED_NOVELL_DATA, savebyte, 2); } } /* * Wait for remote DMA complete. This is necessary because on the * transmit side, data is handled internally by the NIC in bursts and * we can't start another remote DMA until this one completes. Not * waiting causes really bad things to happen - like the NIC * irrecoverably jamming the ISA bus. */ while (((NIC_GET(iot, ioh, nicbase, ED_P0_ISR) & ED_ISR_RDC) != ED_ISR_RDC) && --maxwait); if (!maxwait) { log(LOG_WARNING, "%s: remote transmit DMA failed to complete\n", sc->sc_dev.dv_xname); edreset(sc); } return (len); } /* * Given a source and destination address, copy 'amount' of a packet from the * ring buffer into a linear destination buffer. Takes into account ring-wrap. */ static __inline int ed_ring_copy(sc, src, dst, amount) struct ed_softc *sc; int src; caddr_t dst; u_short amount; { u_short tmp_amount; /* Does copy wrap to lower addr in ring buffer? */ if (src + amount > sc->mem_end) { tmp_amount = sc->mem_end - src; /* Copy amount up to end of NIC memory. */ if (sc->mem_shared) ed_shared_readmem(sc, src, dst, tmp_amount); else ed_pio_readmem(sc, (long)src, dst, tmp_amount); amount -= tmp_amount; src = sc->mem_ring; dst += tmp_amount; } if (sc->mem_shared) ed_shared_readmem(sc, src, dst, amount); else ed_pio_readmem(sc, (long)src, dst, amount); return (src + amount); } /* * Copy data from receive buffer to end of mbuf chain allocate additional mbufs * as needed. Return pointer to last mbuf in chain. * sc = ed info (softc) * src = pointer in ed ring buffer * totlen = maximum packet size */ struct mbuf * edget(sc, src, totlen) struct ed_softc *sc; int src; int totlen; { struct ifnet *ifp = &sc->sc_arpcom.ac_if; struct mbuf *top, **mp, *m; int len, pad; MGETHDR(m, M_DONTWAIT, MT_DATA); if (m == 0) return 0; m->m_pkthdr.rcvif = ifp; m->m_pkthdr.len = totlen; pad = ALIGN(sizeof(struct ether_header)) - sizeof(struct ether_header); m->m_data += pad; len = MHLEN - pad; top = 0; mp = ⊤ while (totlen > 0) { if (top) { MGET(m, M_DONTWAIT, MT_DATA); if (m == 0) { m_freem(top); return 0; } len = MLEN; } if (top && totlen >= MINCLSIZE) { MCLGET(m, M_DONTWAIT); if (m->m_flags & M_EXT) len = MCLBYTES; } m->m_len = len = min(totlen, len); src = ed_ring_copy(sc, src, mtod(m, caddr_t), len); totlen -= len; *mp = m; mp = &m->m_next; } return top; } /* * Compute the multicast address filter from the list of multicast addresses we * need to listen to. */ void ed_getmcaf(ac, af) struct arpcom *ac; u_long *af; { struct ifnet *ifp = &ac->ac_if; struct ether_multi *enm; register u_char *cp, c; register u_long crc; register int i, len; struct ether_multistep step; /* * Set up multicast address filter by passing all multicast addresses * through a crc generator, and then using the high order 6 bits as an * index into the 64 bit logical address filter. The high order bit * selects the word, while the rest of the bits select the bit within * the word. */ if (ifp->if_flags & IFF_PROMISC) { ifp->if_flags |= IFF_ALLMULTI; af[0] = af[1] = 0xffffffff; return; } af[0] = af[1] = 0; ETHER_FIRST_MULTI(step, ac, enm); while (enm != NULL) { if (bcmp(enm->enm_addrlo, enm->enm_addrhi, sizeof(enm->enm_addrlo)) != 0) { /* * We must listen to a range of multicast addresses. * For now, just accept all multicasts, rather than * trying to set only those filter bits needed to match * the range. (At this time, the only use of address * ranges is for IP multicast routing, for which the * range is big enough to require all bits set.) */ ifp->if_flags |= IFF_ALLMULTI; af[0] = af[1] = 0xffffffff; return; } cp = enm->enm_addrlo; crc = 0xffffffff; for (len = sizeof(enm->enm_addrlo); --len >= 0;) { c = *cp++; for (i = 8; --i >= 0;) { if (((crc & 0x80000000) ? 1 : 0) ^ (c & 0x01)) { crc <<= 1; crc ^= 0x04c11db6 | 1; } else crc <<= 1; c >>= 1; } } /* Just want the 6 most significant bits. */ crc >>= 26; /* Turn on the corresponding bit in the filter. */ af[crc >> 5] |= 1 << ((crc & 0x1f) ^ 0); ETHER_NEXT_MULTI(step, enm); } ifp->if_flags &= ~IFF_ALLMULTI; } void ed_shared_writemem(sc, from, card, len) struct ed_softc *sc; caddr_t from; int card, len; { bus_space_tag_t memt = sc->sc_memt; bus_space_handle_t memh = sc->sc_memh; u_int16_t word; /* * For 16-bit cards, 16-bit memory access has already * been set up. Note that some cards are really picky * about enforcing 16-bit access to memory, so we * have to be careful. */ if (sc->isa16bit) { /* * If writing to an odd location, we need to align first. * This requires a read-modify-write cycle as we should * keep accesses 16-bit wide. */ if (len > 0 && (card & 1)) { word = bus_space_read_2(memt, memh, card & ~1); word = (word & 0xff) | (*from << 8); bus_space_write_2(memt, memh, card & ~1, word); from++; card++; len--; } /* XXX I think maybe a bus_space_write_raw_region is needed. */ while (len > 1) { word = (u_int8_t)from[0] | (u_int8_t)from[1] << 8; bus_space_write_2(memt, memh, card, word); from += 2; card += 2; len -= 2; } if (len == 1) { word = *from; bus_space_write_2(memt, memh, card, word); } } else { while (len--) bus_space_write_1(memt, memh, card++, *from++); } } void ed_shared_readmem(sc, card, to, len) struct ed_softc *sc; caddr_t to; int card, len; { bus_space_tag_t memt = sc->sc_memt; bus_space_handle_t memh = sc->sc_memh; u_int16_t word; /* * See comment above re. 16-bit cards. */ if (sc->isa16bit) { /* XXX I think maybe a bus_space_read_raw_region is needed. */ while (len > 1) { word = bus_space_read_2(memt, memh, card); *to++ = word & 0xff; *to++ = word >> 8 & 0xff; card += 2; len -= 2; } if (len == 1) *to = bus_space_read_2(memt, memh, card) & 0xff; } else { while (len--) *to++ = bus_space_read_1(memt, memh, card++); } }