/* $OpenBSD: aic7xxx_reg.h,v 1.3 1997/11/07 08:07:16 niklas Exp $*/ /* * Aic7xxx register and scratch ram definitions. * * Copyright (c) 1994, 1995, 1996 Justin T. Gibbs. * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice immediately at the beginning of the file, without modification, * this list of conditions, and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. The name of the author may not be used to endorse or promote products * derived from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * */ /* * This header is shared by the sequencer code and the kernel level driver. * * All page numbers refer to the Adaptec AIC-7770 Data Book availible from * Adaptec's Technical Documents Department 1-800-934-2766 */ /* * SCSI Sequence Control (p. 3-11). * Each bit, when set starts a specific SCSI sequence on the bus */ #define SCSISEQ 0x000 #define TEMODEO 0x80 #define ENSELO 0x40 #define ENSELI 0x20 #define ENRSELI 0x10 #define ENAUTOATNO 0x08 #define ENAUTOATNI 0x04 #define ENAUTOATNP 0x02 #define SCSIRSTO 0x01 /* * SCSI Transfer Control 0 Register (pp. 3-13). * Controls the SCSI module data path. */ #define SXFRCTL0 0x001 #define DFON 0x80 #define DFPEXP 0x40 #define ULTRAEN 0x20 #define CLRSTCNT 0x10 #define SPIOEN 0x08 #define SCAMEN 0x04 #define CLRCHN 0x02 /* UNUSED 0x01 */ /* * SCSI Transfer Control 1 Register (pp. 3-14,15). * Controls the SCSI module data path. */ #define SXFRCTL1 0x002 #define BITBUCKET 0x80 #define SWRAPEN 0x40 #define ENSPCHK 0x20 #define STIMESEL 0x18 #define ENSTIMER 0x04 #define ACTNEGEN 0x02 #define STPWEN 0x01 /* Powered Termination */ /* * SCSI Control Signal Read Register (p. 3-15). * Reads the actual state of the SCSI bus pins */ #define SCSISIGI 0x003 #define CDI 0x80 #define IOI 0x40 #define MSGI 0x20 #define ATNI 0x10 #define SELI 0x08 #define BSYI 0x04 #define REQI 0x02 #define ACKI 0x01 /* * Possible phases in SCSISIGI */ #define PHASE_MASK 0xe0 #define P_DATAOUT 0x00 #define P_DATAIN 0x40 #define P_COMMAND 0x80 #define P_MESGOUT 0xa0 #define P_STATUS 0xc0 #define P_MESGIN 0xe0 /* * SCSI Contol Signal Write Register (p. 3-16). * Writing to this register modifies the control signals on the bus. Only * those signals that are allowed in the current mode (Initiator/Target) are * asserted. */ #define SCSISIGO 0x003 #define CDO 0x80 #define IOO 0x40 #define MSGO 0x20 #define ATNO 0x10 #define SELO 0x08 #define BSYO 0x04 #define REQO 0x02 #define ACKO 0x01 /* * SCSI Rate Control (p. 3-17). * Contents of this register determine the Synchronous SCSI data transfer * rate and the maximum synchronous Req/Ack offset. An offset of 0 in the * SOFS (3:0) bits disables synchronous data transfers. Any offset value * greater than 0 enables synchronous transfers. */ #define SCSIRATE 0x004 #define WIDEXFER 0x80 /* Wide transfer control */ #define SXFR 0x70 /* Sync transfer rate */ #define SOFS 0x0f /* Sync offset */ /* * SCSI ID (p. 3-18). * Contains the ID of the board and the current target on the * selected channel. */ #define SCSIID 0x005 #define TID 0xf0 /* Target ID mask */ #define OID 0x0f /* Our ID mask */ /* * SCSI Latched Data (p. 3-19). * Read/Write latchs used to transfer data on the SCSI bus during * Automatic or Manual PIO mode. SCSIDATH can be used for the * upper byte of a 16bit wide asyncronouse data phase transfer. */ #define SCSIDATL 0x006 #define SCSIDATH 0x007 /* * SCSI Transfer Count (pp. 3-19,20) * These registers count down the number of bytes transfered * across the SCSI bus. The counter is decremented only once * the data has been safely transfered. SDONE in SSTAT0 is * set when STCNT goes to 0 */ #define STCNT 0x008 #define STCNT0 0x008 #define STCNT1 0x009 #define STCNT2 0x00a /* * Clear SCSI Interrupt 0 (p. 3-20) * Writing a 1 to a bit clears the associated SCSI Interrupt in SSTAT0. */ #define CLRSINT0 0x00b #define CLRSELDO 0x40 #define CLRSELDI 0x20 #define CLRSELINGO 0x10 #define CLRSWRAP 0x08 /* UNUSED 0x04 */ #define CLRSPIORDY 0x02 /* UNUSED 0x01 */ /* * SCSI Status 0 (p. 3-21) * Contains one set of SCSI Interrupt codes * These are most likely of interest to the sequencer */ #define SSTAT0 0x00b #define TARGET 0x80 /* Board acting as target */ #define SELDO 0x40 /* Selection Done */ #define SELDI 0x20 /* Board has been selected */ #define SELINGO 0x10 /* Selection In Progress */ #define SWRAP 0x08 /* 24bit counter wrap */ #define SDONE 0x04 /* STCNT = 0x000000 */ #define SPIORDY 0x02 /* SCSI PIO Ready */ #define DMADONE 0x01 /* DMA transfer completed */ /* * Clear SCSI Interrupt 1 (p. 3-23) * Writing a 1 to a bit clears the associated SCSI Interrupt in SSTAT1. */ #define CLRSINT1 0x00c #define CLRSELTIMEO 0x80 #define CLRATNO 0x40 #define CLRSCSIRSTI 0x20 /* UNUSED 0x10 */ #define CLRBUSFREE 0x08 #define CLRSCSIPERR 0x04 #define CLRPHASECHG 0x02 #define CLRREQINIT 0x01 /* * SCSI Status 1 (p. 3-24) */ #define SSTAT1 0x00c #define SELTO 0x80 #define ATNTARG 0x40 #define SCSIRSTI 0x20 #define PHASEMIS 0x10 #define BUSFREE 0x08 #define SCSIPERR 0x04 #define PHASECHG 0x02 #define REQINIT 0x01 /* * SCSI Interrupt Mode 1 (pp. 3-28,29) * Setting any bit will enable the corresponding function * in SIMODE1 to interrupt via the IRQ pin. */ #define SIMODE1 0x011 #define ENSELTIMO 0x80 #define ENATNTARG 0x40 #define ENSCSIRST 0x20 #define ENPHASEMIS 0x10 #define ENBUSFREE 0x08 #define ENSCSIPERR 0x04 #define ENPHASECHG 0x02 #define ENREQINIT 0x01 /* * SCSI Data Bus (High) (p. 3-29) * This register reads data on the SCSI Data bus directly. */ #define SCSIBUSL 0x012 #define SCSIBUSH 0x013 /* * SCSI/Host Address (p. 3-30) * These registers hold the host address for the byte about to be * transfered on the SCSI bus. They are counted up in the same * manner as STCNT is counted down. SHADDR should always be used * to determine the address of the last byte transfered since HADDR * can be squewed by write ahead. */ #define SHADDR 0x014 #define SHADDR0 0x014 #define SHADDR1 0x015 #define SHADDR2 0x016 #define SHADDR3 0x017 /* * Selection/Reselection ID (p. 3-31) * Upper four bits are the device id. The ONEBIT is set when the re/selecting * device did not set its own ID. */ #define SELID 0x019 #define SELID_MASK 0xf0 #define ONEBIT 0x08 /* UNUSED 0x07 */ /* * SCSI Block Control (p. 3-32) * Controls Bus type and channel selection. In a twin channel configuration * addresses 0x00-0x1e are gated to the appropriate channel based on this * register. SELWIDE allows for the coexistence of 8bit and 16bit devices * on a wide bus. */ #define SBLKCTL 0x01f #define DIAGLEDEN 0x80 /* Aic78X0 only */ #define DIAGLEDON 0x40 /* Aic78X0 only */ #define AUTOFLUSHDIS 0x20 /* UNUSED 0x10 */ #define SELBUS_MASK 0x0a #define SELBUSB 0x08 /* UNUSED 0x04 */ #define SELWIDE 0x02 /* UNUSED 0x01 */ #define SELNARROW 0x00 /* * Sequencer Control (p. 3-33) * Error detection mode and speed configuration */ #define SEQCTL 0x060 #define PERRORDIS 0x80 #define PAUSEDIS 0x40 #define FAILDIS 0x20 #define FASTMODE 0x10 #define BRKADRINTEN 0x08 #define STEP 0x04 #define SEQRESET 0x02 #define LOADRAM 0x01 /* * Sequencer RAM Data (p. 3-34) * Single byte window into the Scratch Ram area starting at the address * specified by SEQADDR0 and SEQADDR1. To write a full word, simply write * four bytes in sucessesion. The SEQADDRs will increment after the most * significant byte is written */ #define SEQRAM 0x061 /* * Sequencer Address Registers (p. 3-35) * Only the first bit of SEQADDR1 holds addressing information */ #define SEQADDR0 0x062 #define SEQADDR1 0x063 #define SEQADDR1_MASK 0x01 /* * Accumulator * We cheat by passing arguments in the Accumulator up to the kernel driver */ #define ACCUM 0x064 #define SINDEX 0x065 #define DINDEX 0x066 #define ALLZEROS 0x06a #define NONE 0x06a #define SINDIR 0x06c #define DINDIR 0x06d #define FUNCTION1 0x06e /* * Host Address (p. 3-48) * This register contains the address of the byte about * to be transfered across the host bus. */ #define HADDR 0x088 #define HADDR0 0x088 #define HADDR1 0x089 #define HADDR2 0x08a #define HADDR3 0x08b #define HCNT 0x08c #define HCNT0 0x08c #define HCNT1 0x08d #define HCNT2 0x08e /* * SCB Pointer (p. 3-49) * Gate one of the four SCBs into the SCBARRAY window. */ #define SCBPTR 0x090 /* * Board Control (p. 3-43) */ #define BCTL 0x084 /* RSVD 0xf0 */ #define ACE 0x08 /* Support for external processors */ /* RSVD 0x06 */ #define ENABLE 0x01 /* * On the aic78X0 chips, Board Control is replaced by the DSCommand * register (p. 4-64) */ #define DSCOMMAND 0x084 #define CACHETHEN 0x80 /* Cache Threshold enable */ #define DPARCKEN 0x40 /* Data Parity Check Enable */ #define MPARCKEN 0x20 /* Memory Parity Check Enable */ #define EXTREQLCK 0x10 /* External Request Lock */ /* * Bus On/Off Time (p. 3-44) */ #define BUSTIME 0x085 #define BOFF 0xf0 #define BON 0x0f /* * Bus Speed (p. 3-45) */ #define BUSSPD 0x086 #define DFTHRSH 0xc0 #define STBOFF 0x38 #define STBON 0x07 #define DFTHRSH_100 0xc0 /* * Host Control (p. 3-47) R/W * Overal host control of the device. */ #define HCNTRL 0x087 /* UNUSED 0x80 */ #define POWRDN 0x40 /* UNUSED 0x20 */ #define SWINT 0x10 #define IRQMS 0x08 #define PAUSE 0x04 #define INTEN 0x02 #define CHIPRST 0x01 #define CHIPRSTACK 0x01 /* * Interrupt Status (p. 3-50) * Status for system interrupts */ #define INTSTAT 0x091 #define SEQINT_MASK 0xf1 /* SEQINT Status Codes */ #define BAD_PHASE 0x01 /* unknown scsi bus phase */ #define SEND_REJECT 0x11 /* sending a message reject */ #define NO_IDENT 0x21 /* no IDENTIFY after reconnect*/ #define NO_MATCH 0x31 /* no cmd match for reconnect */ #define SDTR_MSG 0x41 /* SDTR message received */ #define WDTR_MSG 0x51 /* WDTR message received */ #define REJECT_MSG 0x61 /* Reject message received */ #define BAD_STATUS 0x71 /* Bad status from target */ #define RESIDUAL 0x81 /* Residual byte count != 0 */ #define ABORT_TAG 0x91 /* Sent an ABORT_TAG message */ #define AWAITING_MSG 0xa1 /* * Kernel requested to specify * a message to this target * (command was null), so tell * it that it can fill the * message buffer. */ #define IMMEDDONE 0xb1 /* * An immediate command has * completed */ #define MSG_BUFFER_BUSY 0xc1 /* * Sequencer wants to use the * message buffer, but it * already contains a message */ #define MSGIN_PHASEMIS 0xd1 /* * Target changed phase on us * when we were expecting * another msgin byte. */ #define DATA_OVERRUN 0xe1 /* * Target attempted to write * beyond the bounds of its * command. */ #define BRKADRINT 0x08 #define SCSIINT 0x04 #define CMDCMPLT 0x02 #define SEQINT 0x01 #define INT_PEND (BRKADRINT | SEQINT | SCSIINT | CMDCMPLT) /* * Hard Error (p. 3-53) * Reporting of catastrophic errors. You usually cannot recover from * these without a full board reset. */ #define ERROR 0x092 /* UNUSED 0xf0 */ #define PARERR 0x08 #define ILLOPCODE 0x04 #define ILLSADDR 0x02 #define ILLHADDR 0x01 /* * Clear Interrupt Status (p. 3-52) */ #define CLRINT 0x092 #define CLRBRKADRINT 0x08 #define CLRSCSIINT 0x04 #define CLRCMDINT 0x02 #define CLRSEQINT 0x01 #define DFCNTRL 0x093 #define WIDEODD 0x40 #define SCSIEN 0x20 #define SDMAEN 0x10 #define SDMAENACK 0x10 #define HDMAEN 0x08 #define HDMAENACK 0x08 #define DIRECTION 0x04 #define FIFOFLUSH 0x02 #define FIFORESET 0x01 #define DFSTATUS 0x094 #define HDONE 0x08 #define FIFOEMP 0x01 #define DFDAT 0x099 /* * SCB Auto Increment (p. 3-59) * Byte offset into the SCB Array and an optional bit to allow auto * incrementing of the address during download and upload operations */ #define SCBCNT 0x09a #define SCBAUTO 0x80 #define SCBCNT_MASK 0x1f /* * Queue In FIFO (p. 3-60) * Input queue for queued SCBs (commands that the seqencer has yet to start) */ #define QINFIFO 0x09b /* * Queue In Count (p. 3-60) * Number of queued SCBs */ #define QINCNT 0x09c /* * Queue Out FIFO (p. 3-61) * Queue of SCBs that have completed and await the host */ #define QOUTFIFO 0x09d /* * Queue Out Count (p. 3-61) * Number of queued SCBs in the Out FIFO */ #define QOUTCNT 0x09e /* * SCB Definition (p. 5-4) * The two reserved bytes at SCBARRAY+1[23] are expected to be set to * zero. Bit 3 in SCBARRAY+0 is used as an internal flag to indicate * whether or not to DMA an SCB from host ram. This flag prevents the * "re-fetching" of transactions that are requed because the target is * busy with another command. We also use bits 6 & 7 to indicate whether * or not to initiate SDTR or WDTR repectively when starting this command. */ #define SCBARRAY 0x0a0 #define SCB_CONTROL 0x0a0 #define NEEDWDTR 0x80 #define DISCENB 0x40 #define TAG_ENB 0x20 #define NEEDSDTR 0x10 #define DISCONNECTED 0x04 #define SCB_TAG_TYPE 0x03 #define SCB_TCL 0x0a1 #define SCB_TARGET_STATUS 0x0a2 #define SCB_SGCOUNT 0x0a3 #define SCB_SGPTR 0x0a4 #define SCB_SGPTR0 0x0a4 #define SCB_SGPTR1 0x0a5 #define SCB_SGPTR2 0x0a6 #define SCB_SGPTR3 0x0a7 #define SCB_RESID_SGCNT 0x0a8 #define SCB_RESID_DCNT 0x0a9 #define SCB_RESID_DCNT0 0x0a9 #define SCB_RESID_DCNT1 0x0aa #define SCB_RESID_DCNT2 0x0ab #define SCB_DATAPTR 0x0ac #define SCB_DATAPTR0 0x0ac #define SCB_DATAPTR1 0x0ad #define SCB_DATAPTR2 0x0ae #define SCB_DATAPTR3 0x0af #define SCB_DATACNT 0x0b0 #define SCB_DATACNT0 0x0b0 #define SCB_DATACNT1 0x0b1 #define SCB_DATACNT2 0x0b2 /* UNUSED - QUAD PADDING 0x0b3 */ #define SCB_CMDPTR 0x0b4 #define SCB_CMDPTR0 0x0b4 #define SCB_CMDPTR1 0x0b5 #define SCB_CMDPTR2 0x0b6 #define SCB_CMDPTR3 0x0b7 #define SCB_CMDLEN 0x0b8 #define SCB_TAG 0x0b9 #define SCB_NEXT 0x0ba #define SCB_PREV 0x0bb #ifdef __linux__ #define SG_SIZEOF 0x0c /* sizeof(struct scatterlist) */ #else #define SG_SIZEOF 0x08 /* sizeof(struct ahc_dma) */ #endif /* --------------------- AHA-2840-only definitions -------------------- */ #define SEECTL_2840 0x0c0 /* UNUSED 0xf8 */ #define CS_2840 0x04 #define CK_2840 0x02 #define DO_2840 0x01 #define STATUS_2840 0x0c1 #define EEPROM_TF 0x80 #define BIOS_SEL 0x60 #define ADSEL 0x1e #define DI_2840 0x01 /* --------------------- AIC-7870-only definitions -------------------- */ #define DSPCISTATUS 0x086 /* * Serial EEPROM Control (p. 4-92 in 7870 Databook) * Controls the reading and writing of an external serial 1-bit * EEPROM Device. In order to access the serial EEPROM, you must * first set the SEEMS bit that generates a request to the memory * port for access to the serial EEPROM device. When the memory * port is not busy servicing another request, it reconfigures * to allow access to the serial EEPROM. When this happens, SEERDY * gets set high to verify that the memory port access has been * granted. * * After successful arbitration for the memory port, the SEECS bit of * the SEECTL register is connected to the chip select. The SEECK, * SEEDO, and SEEDI are connected to the clock, data out, and data in * lines respectively. The SEERDY bit of SEECTL is useful in that it * gives us an 800 nsec timer. After a write to the SEECTL register, * the SEERDY goes high 800 nsec later. The one exception to this is * when we first request access to the memory port. The SEERDY goes * high to signify that access has been granted and, for this case, has * no implied timing. * * See 93cx6.c for detailed information on the protocol necessary to * read the serial EEPROM. */ #define SEECTL 0x01e #define EXTARBACK 0x80 #define EXTARBREQ 0x40 #define SEEMS 0x20 #define SEERDY 0x10 #define SEECS 0x08 #define SEECK 0x04 #define SEEDO 0x02 #define SEEDI 0x01 /* ---------------------- Scratch RAM Offsets ------------------------- */ /* These offsets are either to values that are initialized by the board's * BIOS or are specified by the sequencer code. * * The host adapter card (at least the BIOS) uses 20-2f for SCSI * device information, 32-33 and 5a-5f as well. As it turns out, the * BIOS trashes 20-2f, writing the synchronous negotiation results * on top of the BIOS values, so we re-use those for our per-target * scratchspace (actually a value that can be copied directly into * SCSIRATE). The kernel driver will enable synchronous negotiation * for all targets that have a value other than 0 in the lower four * bits of the target scratch space. This should work regardless of * whether the bios has been installed. */ /* * 1 byte per target starting at this address for configuration values */ #define TARG_SCRATCH 0x020 /* * The sequencer will stick the frist byte of any rejected message here so * we can see what is getting thrown away. Extended messages put the * extended message type in REJBYTE_EXT. */ #define REJBYTE 0x030 #define REJBYTE_EXT 0x031 /* * Bit vector of targets that have disconnection disabled. */ #define DISC_DSB 0x032 #define DISC_DSB_A 0x032 #define DISC_DSB_B 0x033 /* * Length of pending message */ #define MSG_LEN 0x034 /* We reserve 8bytes to store outgoing messages */ #define MSG0 0x035 #define COMP_MSG0 0xcb /* 2's complement of MSG0 */ #define MSG1 0x036 #define MSG2 0x037 #define MSG3 0x038 #define MSG4 0x039 #define MSG5 0x03a #define MSG6 0x03b #define MSG7 0x03c /* * These are offsets into the card's scratch ram. Some of the values are * specified in the AHA2742 technical reference manual and are initialized * by the BIOS at boot time. */ #define LASTPHASE 0x03d #define ARG_1 0x03e #define MAXOFFSET 0x01 #define RETURN_1 0x03f #define SEND_WDTR 0x80 #define SEND_SDTR 0x60 #define SEND_SENSE 0x40 #define SEND_REJ 0x20 #define SCB_PAGEDIN 0x10 #define SIGSTATE 0x040 #define DMAPARAMS 0x041 /* Parameters for DMA Logic */ #define SG_COUNT 0x042 #define SG_NEXT 0x043 /* working value of SG pointer */ #define SG_NEXT0 0x043 #define SG_NEXT1 0x044 #define SG_NEXT2 0x045 #define SG_NEXT3 0x046 #define SCBCOUNT 0x047 /* * Number of SCBs supported by * this card. */ #define COMP_SCBCOUNT 0x048 /* * Two's compliment of SCBCOUNT */ #define QCNTMASK 0x049 /* * Mask of bits to test against * when looking at the Queue Count * registers. Works around a bug * on aic7850 chips. */ #define FLAGS 0x04a #define SINGLE_BUS 0x00 #define TWIN_BUS 0x01 #define WIDE_BUS 0x02 #define PAGESCBS 0x04 #define DPHASE 0x10 #define SELECTED 0x20 #define IDENTIFY_SEEN 0x40 #define RESELECTED 0x80 #define SAVED_TCL 0x04b /* * Temporary storage for the * target/channel/lun of a * reconnecting target */ #define ACTIVE_A 0x04c #define ACTIVE_B 0x04d #define WAITING_SCBH 0x04e /* * head of list of SCBs awaiting * selection */ #define DISCONNECTED_SCBH 0x04f /* * head of list of SCBs that are * disconnected. Used for SCB * paging. */ #define SCB_LIST_NULL 0xff #define SAVED_LINKPTR 0x050 #define SAVED_SCBPTR 0x051 #define ULTRA_ENB 0x052 #define ULTRA_ENB_B 0x053 #define SCSICONF 0x05a #define RESET_SCSI 0x40 #define HOSTCONF 0x05d #define HA_274_BIOSCTRL 0x05f #define BIOSMODE 0x30 #define BIOSDISABLED 0x30 #define CHANNEL_B_PRIMARY 0x08 /* Message codes */ #define MSG_EXTENDED 0x01 #define MSG_SDTR 0x01 #define MSG_WDTR 0x03 #define MSG_SDPTRS 0x02 #define MSG_RDPTRS 0x03 #define MSG_DISCONNECT 0x04 #define MSG_INITIATOR_DET_ERROR 0x05 #define MSG_ABORT 0x06 #define MSG_REJECT 0x07 #define MSG_NOP 0x08 #define MSG_MSG_PARITY_ERROR 0x09 #define MSG_BUS_DEVICE_RESET 0x0c #define MSG_ABORT_TAG 0x0d #define MSG_SIMPLE_TAG 0x20 #define MSG_IDENTIFY 0x80 /* WDTR Message values */ #define BUS_8_BIT 0x00 #define BUS_16_BIT 0x01 #define BUS_32_BIT 0x02 #define MAX_OFFSET_8BIT 0x0f #define MAX_OFFSET_16BIT 0x08