/* $OpenBSD: ciphyreg.h,v 1.3 2015/07/19 06:28:12 yuo Exp $ */ /* $FreeBSD: ciphyreg.h,v 1.1 2004/09/10 20:57:45 wpaul Exp $ */ /* * Copyright (c) 2004 * Bill Paul . All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. All advertising materials mentioning features or use of this software * must display the following acknowledgement: * This product includes software developed by Bill Paul. * 4. Neither the name of the author nor the names of any co-contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF * THE POSSIBILITY OF SUCH DAMAGE. */ #ifndef _DEV_MII_CIPHYREG_H_ #define _DEV_MII_CIPHYREG_H_ /* * Register definitions for the Cicada CS8201 10/100/1000 gigE copper * PHY, embedded within the VIA Networks VT6122 controller. */ /* Vendor-specific PHY registers */ /* 100baseTX status extention register */ #define CIPHY_MII_100STS 0x10 #define CIPHY_100STS_DESLCK 0x8000 /* descrambler locked */ #define CIPHY_100STS_LKCERR 0x4000 /* lock error detected/lock lost */ #define CIPHY_100STS_DISC 0x2000 /* disconnect state */ #define CIPHY_100STS_LINK 0x1000 /* current link state */ #define CIPHY_100STS_RXERR 0x0800 /* receive error detected */ #define CIPHY_100STS_TXERR 0x0400 /* transmit error detected */ #define CIPHY_100STS_SSDERR 0x0200 /* false carrier error detected */ #define CIPHY_100STS_ESDERR 0x0100 /* premature end of stream error */ /* 1000BT status extention register #2 */ #define CIPHY_MII_1000STS2 0x11 #define CIPHY_1000STS2_DESLCK 0x8000 /* descrambler locked */ #define CIPHY_1000STS2_LKCERR 0x4000 /* lock error detected/lock lost */ #define CIPHY_1000STS2_DISC 0x2000 /* disconnect state */ #define CIPHY_1000STS2_LINK 0x1000 /* current link state */ #define CIPHY_1000STS2_RXERR 0x0800 /* receive error detected */ #define CIPHY_1000STS2_TXERR 0x0400 /* transmit error detected */ #define CIPHY_1000STS2_SSDERR 0x0200 /* false carrier error detected */ #define CIPHY_1000STS2_ESDERR 0x0100 /* premature end of stream error */ #define CIPHY_1000STS2_CARREXT 0x0080 /* carrier extention err detected */ #define CIPHY_1000STS2_BCM5400 0x0040 /* non-complient BCM5400 detected */ /* Bypass control register */ #define CIPHY_MII_BYPASS 0x12 #define CIPHY_BYPASS_TX 0x8000 /* transmit disable */ #define CIPHY_BYPASS_4B5B 0x4000 /* bypass the 4B5B encoder */ #define CIPHY_BYPASS_SCRAM 0x2000 /* bypass scrambler */ #define CIPHY_BYPASS_DSCAM 0x1000 /* bypass descrambler */ #define CIPHY_BYPASS_PCSRX 0x0800 /* bypass PCS receive */ #define CIPHY_BYPASS_PCSTX 0x0400 /* bypass PCS transmit */ #define CIPHY_BYPASS_LFI 0x0200 /* bypass LFI timer */ #define CIPHY_BYPASS_TXCLK 0x0100 /* enable transmit clock on LED4 pin */ #define CIPHY_BYPASS_BCM5400_F 0x0080 /* force BCM5400 detect */ #define CIPHY_BYPASS_BCM5400 0x0040 /* bypass BCM5400 detect */ #define CIPHY_BYPASS_PAIRSWAP 0x0020 /* disable automatic pair swap */ #define CIPHY_BYPASS_POLARITY 0x0010 /* disable polarity correction */ #define CIPHY_BYPASS_PARALLEL 0x0008 /* parallel detect enable */ #define CIPHY_BYPASS_PULSE 0x0004 /* disable pulse shaping filter */ #define CIPHY_BYPASS_1000BNP 0x0002 /* disable 1000BT next page exchange */ /* RX error count register */ #define CIPHY_MII_RXERR 0x13 /* False carrier sense count register */ #define CIPHY_MII_FCSERR 0x14 /* Ddisconnect error counter */ #define CIPHY_MII_DISCERR 0x15 /* 10baseT control/status register */ #define CIPHY_MII_10BTCSR 0x16 #define CIPHY_10BTCSR_DLIT 0x8000 /* Disable data link integrity test */ #define CIPHY_10BTCSR_JABBER 0x4000 /* Disable jabber detect */ #define CIPHY_10BTCSR_ECHO 0x2000 /* Disable echo mode */ #define CIPHY_10BTCSR_SQE 0x1000 /* Disable signal quality error */ #define CIPHY_10BTCSR_SQUENCH 0x0C00 /* Squelch control */ #define CIPHY_10BTCSR_EOFERR 0x0100 /* End of Frame error */ #define CIPHY_10BTCSR_DISC 0x0080 /* Disconnect status */ #define CIPHY_10BTCSR_LINK 0x0040 /* current link state */ #define CIPHY_10BTCSR_ITRIM 0x0038 /* current reference trim */ #define CIPHY_10BTCSR_CSR 0x0006 /* CSR behavior control */ #define CIPHY_SQUELCH_300MV 0x0000 #define CIPHY_SQUELCH_197MV 0x0400 #define CIPHY_SQUELCH_450MV 0x0800 #define CIPHY_SQUELCH_RSVD 0x0C00 #define CIPHY_ITRIM_PLUS2 0x0000 #define CIPHY_ITRIM_PLUS4 0x0008 #define CIPHY_ITRIM_PLUS6 0x0010 #define CIPHY_ITRIM_PLUS6_ 0x0018 #define CIPHY_ITRIM_MINUS4 0x0020 #define CIPHY_ITRIM_MINUS4_ 0x0028 #define CIPHY_ITRIM_MINUS2 0x0030 #define CIPHY_ITRIM_ZERO 0x0038 /* Extended PHY control register #1 */ #define CIPHY_MII_ECTL1 0x17 #define CIPHY_ECTL1_ACTIPHY 0x0020 /* Enable ActiPHY power saving */ #define CIPHY_ECTL1_IOVOL 0x0e00 /* MAC interface and I/O voltage select */ #define CIPHY_ECTL1_INTSEL 0xf000 /* select MAC interface */ #define CIPHY_IOVOL_3300MV 0x0000 /* 3.3V for I/O pins */ #define CIPHY_IOVOL_2500MV 0x0200 /* 2.5V for I/O pins */ #define CIPHY_INTSEL_GMII 0x0000 /* GMII/MII */ #define CIPHY_INTSEL_RGMII 0x1000 #define CIPHY_INTSEL_TBI 0x2000 #define CIPHY_INTSEL_RTBI 0x3000 /* Extended PHY control register #2 */ #define CIPHY_MII_ECTL2 0x18 #define CIPHY_ECTL2_ERATE 0xE000 /* 10/1000 edge rate control */ #define CIPHY_ECTL2_VTRIM 0x1C00 /* voltage reference trim */ #define CIPHY_ECTL2_CABLELEN 0x000E /* Cable quality/length */ #define CIPHY_ECTL2_ANALOGLOOP 0x0001 /* 1000BT analog loopback */ #define CIPHY_CABLELEN_0TO10M 0x0000 #define CIPHY_CABLELEN_10TO20M 0x0002 #define CIPHY_CABLELEN_20TO40M 0x0004 #define CIPHY_CABLELEN_40TO80M 0x0006 #define CIPHY_CABLELEN_80TO100M 0x0008 #define CIPHY_CABLELEN_100TO140M 0x000A #define CIPHY_CABLELEN_140TO180M 0x000C #define CIPHY_CABLELEN_OVER180M 0x000E /* Interrupt mask register */ #define CIPHY_MII_IMR 0x19 #define CIPHY_IMR_PINENABLE 0x8000 /* Interrupt pin enable */ #define CIPHY_IMR_SPEED 0x4000 /* speed changed event */ #define CIPHY_IMR_LINK 0x2000 /* link change/ActiPHY event */ #define CIPHY_IMR_DPX 0x1000 /* duplex change event */ #define CIPHY_IMR_ANEGERR 0x0800 /* autoneg error event */ #define CIPHY_IMR_ANEGDONE 0x0400 /* autoneg done event */ #define CIPHY_IMR_NPRX 0x0200 /* page received event */ #define CIPHY_IMR_SYMERR 0x0100 /* symbol error event */ #define CIPHY_IMR_LOCKERR 0x0080 /* descrambler lock lost event */ #define CIPHY_IMR_XOVER 0x0040 /* MDI crossover change event */ #define CIPHY_IMR_POLARITY 0x0020 /* polarity change event */ #define CIPHY_IMR_JABBER 0x0010 /* jabber detect event */ #define CIPHY_IMR_SSDERR 0x0008 /* false carrier detect event */ #define CIPHY_IMR_ESDERR 0x0004 /* parallel detect error event */ #define CIPHY_IMR_MASTERSLAVE 0x0002 /* master/slave resolve done event */ #define CIPHY_IMR_RXERR 0x0001 /* RX error event */ /* Interrupt status register */ #define CIPHY_MII_ISR 0x1A #define CIPHY_ISR_IPENDING 0x8000 /* Interrupt is pending */ #define CIPHY_ISR_SPEED 0x4000 /* speed changed event */ #define CIPHY_ISR_LINK 0x2000 /* link change/ActiPHY event */ #define CIPHY_ISR_DPX 0x1000 /* duplex change event */ #define CIPHY_ISR_ANEGERR 0x0800 /* autoneg error event */ #define CIPHY_ISR_ANEGDONE 0x0400 /* autoneg done event */ #define CIPHY_ISR_NPRX 0x0200 /* page received event */ #define CIPHY_ISR_SYMERR 0x0100 /* symbol error event */ #define CIPHY_ISR_LOCKERR 0x0080 /* descrambler lock lost event */ #define CIPHY_ISR_XOVER 0x0040 /* MDI crossover change event */ #define CIPHY_ISR_POLARITY 0x0020 /* polarity change event */ #define CIPHY_ISR_JABBER 0x0010 /* jabber detect event */ #define CIPHY_ISR_SSDERR 0x0008 /* false carrier detect event */ #define CIPHY_ISR_ESDERR 0x0004 /* parallel detect error event */ #define CIPHY_ISR_MASTERSLAVE 0x0002 /* master/slave resolve done event */ #define CIPHY_ISR_RXERR 0x0001 /* RX error event */ /* LED control register */ #define CIPHY_MII_LED 0x1B #define CIPHY_LED_LINK10FORCE 0x8000 /* Force on link10 LED */ #define CIPHY_LED_LINK10DIS 0x4000 /* Disable link10 LED */ #define CIPHY_LED_LINK100FORCE 0x2000 /* Force on link10 LED */ #define CIPHY_LED_LINK100DIS 0x1000 /* Disable link100 LED */ #define CIPHY_LED_LINK1000FORCE 0x0800 /* Force on link1000 LED */ #define CIPHY_LED_LINK1000DIS 0x0400 /* Disable link1000 LED */ #define CIPHY_LED_FDXFORCE 0x0200 /* Force on duplex LED */ #define CIPHY_LED_FDXDIS 0x0100 /* Disable duplex LED */ #define CIPHY_LED_ACTFORCE 0x0080 /* Force on activity LED */ #define CIPHY_LED_ACTDIS 0x0040 /* Disable activity LED */ #define CIPHY_LED_PULSE 0x0008 /* LED pulse enable */ #define CIPHY_LED_LINKACTBLINK 0x0004 /* enable link/activity LED blink */ #define CIPHY_LED_BLINKRATE 0x0002 /* blink rate 0=10hz, 1=5hz */ /* Auxilliary control and status register */ #define CIPHY_MII_AUXCSR 0x1C #define CIPHY_AUXCSR_ANEGDONE 0x8000 /* Autoneg complete */ #define CIPHY_AUXCSR_ANEGOFF 0x4000 /* Autoneg disabled */ #define CIPHY_AUXCSR_XOVER 0x2000 /* MDI/MDI-X crossover indication */ #define CIPHY_AUXCSR_PAIRSWAP 0x1000 /* pair swap indication */ #define CIPHY_AUXCSR_APOLARITY 0x0800 /* polarity inversion pair A */ #define CIPHY_AUXCSR_BPOLARITY 0x0400 /* polarity inversion pair B */ #define CIPHY_AUXCSR_CPOLARITY 0x0200 /* polarity inversion pair C */ #define CIPHY_AUXCSR_DPOLARITY 0x0100 /* polarity inversion pair D */ #define CIPHY_AUXCSR_FDX 0x0020 /* duplex 1=full, 0=half */ #define CIPHY_AUXCSR_SPEED 0x0018 /* speed */ #define CIPHY_AUXCSR_MDPPS 0x0004 /* No idea, not documented */ #define CIPHY_AUXCSR_STICKYREST 0x0002 /* reset clears sticky bits */ #define CIPHY_SPEED10 0x0000 #define CIPHY_SPEED100 0x0008 #define CIPHY_SPEED1000 0x0010 /* Delay skew status register */ #define CIPHY_MII_DSKEW 0x1D #define CIPHY_DSKEW_PAIRA 0x7000 /* Pair A skew in symbol times */ #define CIPHY_DSKEW_PAIRB 0x0700 /* Pair B skew in symbol times */ #define CIPHY_DSKEW_PAIRC 0x0070 /* Pair C skew in symbol times */ #define CIPHY_DSKEW_PAIRD 0x0007 /* Pair D skew in symbol times */ #endif /* _DEV_CIPHY_MIIREG_H_ */