/* $OpenBSD: if_tlreg.h,v 1.6 2001/02/03 05:52:27 mickey Exp $ */ /* * Copyright (c) 1997, 1998 * Bill Paul . All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. All advertising materials mentioning features or use of this software * must display the following acknowledgement: * This product includes software developed by Bill Paul. * 4. Neither the name of the author nor the names of any co-contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF * THE POSSIBILITY OF SUCH DAMAGE. * * $FreeBSD: if_tlreg.h,v 1.7 1998/10/31 17:23:48 wpaul Exp $ */ struct tl_type { u_int16_t tl_vid; u_int16_t tl_did; char *tl_name; }; /* * ThunderLAN TX/RX list format. The TX and RX lists are pretty much * identical: the list begins with a 32-bit forward pointer which points * at the next list in the chain, followed by 16 bits for the total * frame size, and a 16 bit status field. This is followed by a series * of 10 32-bit data count/data address pairs that point to the fragments * that make up the complete frame. */ #define TL_MAXFRAGS 10 #define TL_RX_LIST_CNT 20 #define TL_TX_LIST_CNT 20 #define TL_MIN_FRAMELEN 64 struct tl_frag { u_int32_t tlist_dcnt; u_int32_t tlist_dadr; }; struct tl_list { u_int32_t tlist_fptr; /* phys address of next list */ u_int16_t tlist_cstat; /* status word */ u_int16_t tlist_frsize; /* size of data in frame */ struct tl_frag tl_frag[TL_MAXFRAGS]; }; /* * This is a special case of an RX list. By setting the One_Frag * bit in the NETCONFIG register, the driver can force the ThunderLAN * chip to use only one fragment when DMAing RX frames. */ struct tl_list_onefrag { u_int32_t tlist_fptr; u_int16_t tlist_cstat; u_int16_t tlist_frsize; struct tl_frag tl_frag; }; struct tl_list_data { struct tl_list_onefrag tl_rx_list[TL_RX_LIST_CNT]; struct tl_list tl_tx_list[TL_TX_LIST_CNT]; unsigned char tl_pad[TL_MIN_FRAMELEN]; }; struct tl_chain { struct tl_list *tl_ptr; struct mbuf *tl_mbuf; struct tl_chain *tl_next; }; struct tl_chain_onefrag { struct tl_list_onefrag *tl_ptr; struct mbuf *tl_mbuf; struct tl_chain_onefrag *tl_next; }; struct tl_chain_data { struct tl_chain_onefrag tl_rx_chain[TL_RX_LIST_CNT]; struct tl_chain tl_tx_chain[TL_TX_LIST_CNT]; struct tl_chain_onefrag *tl_rx_head; struct tl_chain_onefrag *tl_rx_tail; struct tl_chain *tl_tx_head; struct tl_chain *tl_tx_tail; struct tl_chain *tl_tx_free; }; struct tl_softc { struct device sc_dev; /* generic device structure */ void * sc_ih; /* interrupt handler cookie */ struct arpcom arpcom; /* interface info */ struct ifmedia ifmedia; /* media info */ struct timeout tl_stats_tmo, tl_wait_tmo; bus_space_handle_t tl_bhandle; bus_space_tag_t tl_btag; struct tl_type *tl_dinfo; /* ThunderLAN adapter info */ struct tl_type *tl_pinfo; /* PHY info struct */ u_int8_t tl_ctlr; /* chip number */ u_int8_t tl_unit; /* interface number */ u_int8_t tl_eeaddr; u_int8_t tl_phy_addr; /* PHY address */ u_int8_t tl_tx_pend; /* TX pending */ u_int8_t tl_want_auto; /* autoneg scheduled */ u_int8_t tl_autoneg; /* autoneg in progress */ u_int16_t tl_phy_sts; /* PHY status */ u_int16_t tl_phy_vid; /* PHY vendor ID */ u_int16_t tl_phy_did; /* PHY device ID */ caddr_t tl_ldata_ptr; struct tl_list_data *tl_ldata; /* TX/RX lists and mbufs */ struct tl_chain_data tl_cdata; u_int8_t tl_txeoc; u_int8_t tl_bitrate; }; /* * Transmit interrupt threshold. */ #define TX_THR 0x00000004 #define TL_FLAG_FORCEDELAY 1 #define TL_FLAG_SCHEDDELAY 2 #define TL_FLAG_DELAYTIMEO 3 /* * The ThunderLAN supports up to 32 PHYs. */ #define TL_PHYADDR_MIN 0x00 #define TL_PHYADDR_MAX 0x1F #define PHY_UNKNOWN 6 #define TL_PHYS_IDLE -1 /* * General constants that are fun to know. * * The ThunderLAN controller is made by Texas Instruments. The * manual indicates that if the EEPROM checksum fails, the PCI * vendor and device ID registers will be loaded with TI-specific * values. */ #define TI_VENDORID 0x104C #define TI_DEVICEID_THUNDERLAN 0x0500 /* * Known PHY Ids. According to the Level 1 documentation (which is * very nice, incidentally), here's how they work: * * The PHY identifier register #1 is composed of bits 3 through 18 * of the OUI. (First 16-bit word.) * The PHY identifier register #2 is composed of bits 19 through 24 * if the OUI. * This is followed by 6 bits containing the manufacturer's model * number. * Lastly, there are 4 bits for the manufacturer's revision number. * * Honestly, there are a lot of these that don't make any sense; the * only way to be really sure is to look at the data sheets. */ /* * Texas Instruments PHY identifiers * * The ThunderLAN manual has a curious and confusing error in it. * In chapter 7, which describes PHYs, it says that TI PHYs have * the following ID codes, where xx denotes a revision: * * 0x4000501xx internal 10baseT PHY * 0x4000502xx TNETE211 100VG-AnyLan PMI * * The problem here is that these are not valid 32-bit hex numbers: * there's one digit too many. My guess is that they mean the internal * 10baseT PHY is 0x4000501x and the TNETE211 is 0x4000502x since these * are the only numbers that make sense. */ #define TI_PHY_VENDORID 0x4000 #define TI_PHY_10BT 0x501F #define TI_PHY_100VGPMI 0x502F /* * These ID values are for the NS DP83840A 10/100 PHY */ #define NS_PHY_VENDORID 0x2000 #define NS_PHY_83840A 0x5C0F /* * Level 1 10/100 PHY */ #define LEVEL1_PHY_VENDORID 0x7810 #define LEVEL1_PHY_LXT970 0x000F /* * Intel 82555 10/100 PHY */ #define INTEL_PHY_VENDORID 0x0A28 #define INTEL_PHY_82555 0x015F /* * SEEQ 80220 10/100 PHY */ #define SEEQ_PHY_VENDORID 0x0016 #define SEEQ_PHY_80220 0xF83F /* * These are the PCI vendor and device IDs for Compaq ethernet * adapters based on the ThunderLAN controller. */ #define COMPAQ_VENDORID 0x0E11 #define COMPAQ_DEVICEID_NETEL_10_100 0xAE32 #define COMPAQ_DEVICEID_NETEL_UNKNOWN 0xAE33 #define COMPAQ_DEVICEID_NETEL_10 0xAE34 #define COMPAQ_DEVICEID_NETFLEX_3P_INTEGRATED 0xAE35 #define COMPAQ_DEVICEID_NETEL_10_100_DUAL 0xAE40 #define COMPAQ_DEVICEID_NETEL_10_100_PROLIANT 0xAE43 #define COMPAQ_DEVICEID_NETEL_10_100_EMBEDDED 0xB011 #define COMPAQ_DEVICEID_NETEL_10_T2_UTP_COAX 0xB012 #define COMPAQ_DEVICEID_NETEL_10_100_TX_UTP 0xB030 #define COMPAQ_DEVICEID_NETFLEX_3P 0xF130 #define COMPAQ_DEVICEID_NETFLEX_3P_BNC 0xF150 /* * These are the PCI vendor and device IDs for Olicom * adapters based on the ThunderLAN controller. */ #define OLICOM_VENDORID 0x108D #define OLICOM_DEVICEID_OC2183 0x0013 #define OLICOM_DEVICEID_OC2325 0x0012 #define OLICOM_DEVICEID_OC2326 0x0014 /* * PCI low memory base and low I/O base */ #define TL_PCI_LOIO 0x10 #define TL_PCI_LOMEM 0x14 /* * PCI latency timer (it's actually 0x0D, but we want a value * that's longword aligned). */ #define TL_PCI_LATENCY_TIMER 0x0C #define TL_DIO_ADDR_INC 0x8000 /* Increment addr on each read */ #define TL_DIO_RAM_SEL 0x4000 /* RAM address select */ #define TL_DIO_ADDR_MASK 0x3FFF /* address bits mask */ /* * Interrupt types */ #define TL_INTR_INVALID 0x0 #define TL_INTR_TXEOF 0x1 #define TL_INTR_STATOFLOW 0x2 #define TL_INTR_RXEOF 0x3 #define TL_INTR_DUMMY 0x4 #define TL_INTR_TXEOC 0x5 #define TL_INTR_ADCHK 0x6 #define TL_INTR_RXEOC 0x7 #define TL_INT_MASK 0x001C #define TL_VEC_MASK 0x1FE0 /* * Host command register bits */ #define TL_CMD_GO 0x80000000 #define TL_CMD_STOP 0x40000000 #define TL_CMD_ACK 0x20000000 #define TL_CMD_CHSEL7 0x10000000 #define TL_CMD_CHSEL6 0x08000000 #define TL_CMD_CHSEL5 0x04000000 #define TL_CMD_CHSEL4 0x02000000 #define TL_CMD_CHSEL3 0x01000000 #define TL_CMD_CHSEL2 0x00800000 #define TL_CMD_CHSEL1 0x00400000 #define TL_CMD_CHSEL0 0x00200000 #define TL_CMD_EOC 0x00100000 #define TL_CMD_RT 0x00080000 #define TL_CMD_NES 0x00040000 #define TL_CMD_ZERO0 0x00020000 #define TL_CMD_ZERO1 0x00010000 #define TL_CMD_ADRST 0x00008000 #define TL_CMD_LDTMR 0x00004000 #define TL_CMD_LDTHR 0x00002000 #define TL_CMD_REQINT 0x00001000 #define TL_CMD_INTSOFF 0x00000800 #define TL_CMD_INTSON 0x00000400 #define TL_CMD_RSVD0 0x00000200 #define TL_CMD_RSVD1 0x00000100 #define TL_CMD_ACK7 0x00000080 #define TL_CMD_ACK6 0x00000040 #define TL_CMD_ACK5 0x00000020 #define TL_CMD_ACK4 0x00000010 #define TL_CMD_ACK3 0x00000008 #define TL_CMD_ACK2 0x00000004 #define TL_CMD_ACK1 0x00000002 #define TL_CMD_ACK0 0x00000001 #define TL_CMD_CHSEL_MASK 0x01FE0000 #define TL_CMD_ACK_MASK 0xFF /* * EEPROM address where station address resides. */ #define TL_EEPROM_EADDR 0x83 #define TL_EEPROM_EADDR2 0x99 #define TL_EEPROM_EADDR3 0xAF #define TL_EEPROM_EADDR_OC 0xF8 /* Olicom cards use a different address than Compaqs. */ /* * ThunderLAN host command register offsets. * (Can be accessed either by IO ports or memory map.) */ #define TL_HOSTCMD 0x00 #define TL_CH_PARM 0x04 #define TL_DIO_ADDR 0x08 #define TL_HOST_INT 0x0A #define TL_DIO_DATA 0x0C /* * ThunderLAN internal registers */ #define TL_NETCMD 0x00 #define TL_NETSIO 0x01 #define TL_NETSTS 0x02 #define TL_NETMASK 0x03 #define TL_NETCONFIG 0x04 #define TL_MANTEST 0x06 #define TL_VENID_LSB 0x08 #define TL_VENID_MSB 0x09 #define TL_DEVID_LSB 0x0A #define TL_DEVID_MSB 0x0B #define TL_REVISION 0x0C #define TL_SUBCLASS 0x0D #define TL_MINLAT 0x0E #define TL_MAXLAT 0x0F #define TL_AREG0_B5 0x10 #define TL_AREG0_B4 0x11 #define TL_AREG0_B3 0x12 #define TL_AREG0_B2 0x13 #define TL_AREG0_B1 0x14 #define TL_AREG0_B0 0x15 #define TL_AREG1_B5 0x16 #define TL_AREG1_B4 0x17 #define TL_AREG1_B3 0x18 #define TL_AREG1_B2 0x19 #define TL_AREG1_B1 0x1A #define TL_AREG1_B0 0x1B #define TL_AREG2_B5 0x1C #define TL_AREG2_B4 0x1D #define TL_AREG2_B3 0x1E #define TL_AREG2_B2 0x1F #define TL_AREG2_B1 0x20 #define TL_AREG2_B0 0x21 #define TL_AREG3_B5 0x22 #define TL_AREG3_B4 0x23 #define TL_AREG3_B3 0x24 #define TL_AREG3_B2 0x25 #define TL_AREG3_B1 0x26 #define TL_AREG3_B0 0x27 #define TL_HASH1 0x28 #define TL_HASH2 0x2C #define TL_TXGOODFRAMES 0x30 #define TL_TXUNDERRUN 0x33 #define TL_RXGOODFRAMES 0x34 #define TL_RXOVERRUN 0x37 #define TL_DEFEREDTX 0x38 #define TL_CRCERROR 0x3A #define TL_CODEERROR 0x3B #define TL_MULTICOLTX 0x3C #define TL_SINGLECOLTX 0x3E #define TL_EXCESSIVECOL 0x40 #define TL_LATECOL 0x41 #define TL_CARRIERLOSS 0x42 #define TL_ACOMMIT 0x43 #define TL_LDREG 0x44 #define TL_BSIZEREG 0x45 #define TL_MAXRX 0x46 /* * ThunderLAN SIO register bits */ #define TL_SIO_MINTEN 0x80 #define TL_SIO_ECLOK 0x40 #define TL_SIO_ETXEN 0x20 #define TL_SIO_EDATA 0x10 #define TL_SIO_NMRST 0x08 #define TL_SIO_MCLK 0x04 #define TL_SIO_MTXEN 0x02 #define TL_SIO_MDATA 0x01 /* * Thunderlan NETCONFIG bits */ #define TL_CFG_RCLKTEST 0x8000 #define TL_CFG_TCLKTEST 0x4000 #define TL_CFG_BITRATE 0x2000 #define TL_CFG_RXCRC 0x1000 #define TL_CFG_PEF 0x0800 #define TL_CFG_ONEFRAG 0x0400 #define TL_CFG_ONECHAN 0x0200 #define TL_CFG_MTEST 0x0100 #define TL_CFG_PHYEN 0x0080 #define TL_CFG_MACSEL6 0x0040 #define TL_CFG_MACSEL5 0x0020 #define TL_CFG_MACSEL4 0x0010 #define TL_CFG_MACSEL3 0x0008 #define TL_CFG_MACSEL2 0x0004 #define TL_CFG_MACSEL1 0x0002 #define TL_CFG_MACSEL0 0x0001 /* * ThunderLAN NETSTS bits */ #define TL_STS_MIRQ 0x80 #define TL_STS_HBEAT 0x40 #define TL_STS_TXSTOP 0x20 #define TL_STS_RXSTOP 0x10 /* * ThunderLAN NETCMD bits */ #define TL_CMD_NRESET 0x80 #define TL_CMD_NWRAP 0x40 #define TL_CMD_CSF 0x20 #define TL_CMD_CAF 0x10 #define TL_CMD_NOBRX 0x08 #define TL_CMD_DUPLEX 0x04 #define TL_CMD_TRFRAM 0x02 #define TL_CMD_TXPACE 0x01 /* * ThunderLAN NETMASK bits */ #define TL_MASK_MASK7 0x80 #define TL_MASK_MASK6 0x40 #define TL_MASK_MASK5 0x20 #define TL_MASK_MASK4 0x10 /* * MII frame format */ #ifdef ANSI_DOESNT_ALLOW_BITFIELDS struct tl_mii_frame { u_int16_t mii_stdelim:2, mii_opcode:2, mii_phyaddr:5, mii_regaddr:5, mii_turnaround:2; u_int16_t mii_data; }; #else struct tl_mii_frame { u_int8_t mii_stdelim; u_int8_t mii_opcode; u_int8_t mii_phyaddr; u_int8_t mii_regaddr; u_int8_t mii_turnaround; u_int16_t mii_data; }; #endif /* * MII constants */ #define TL_MII_STARTDELIM 0x01 #define TL_MII_READOP 0x02 #define TL_MII_WRITEOP 0x01 #define TL_MII_TURNAROUND 0x02 #define TL_LAST_FRAG 0x80000000 #define TL_CSTAT_UNUSED 0x8000 #define TL_CSTAT_FRAMECMP 0x4000 #define TL_CSTAT_READY 0x3000 #define TL_CSTAT_UNUSED13 0x2000 #define TL_CSTAT_UNUSED12 0x1000 #define TL_CSTAT_EOC 0x0800 #define TL_CSTAT_RXERROR 0x0400 #define TL_CSTAT_PASSCRC 0x0200 #define TL_CSTAT_DPRIO 0x0100 #define TL_FRAME_MASK 0x00FFFFFF #define tl_tx_goodframes(x) (x.tl_txstat & TL_FRAME_MASK) #define tl_tx_underrun(x) ((x.tl_txstat & ~TL_FRAME_MASK) >> 24) #define tl_rx_goodframes(x) (x.tl_rxstat & TL_FRAME_MASK) #define tl_rx_overrun(x) ((x.tl_rxstat & ~TL_FRAME_MASK) >> 24) struct tl_stats { u_int32_t tl_txstat; u_int32_t tl_rxstat; u_int16_t tl_deferred; u_int8_t tl_crc_errors; u_int8_t tl_code_errors; u_int16_t tl_tx_multi_collision; u_int16_t tl_tx_single_collision; u_int8_t tl_excessive_collision; u_int8_t tl_late_collision; u_int8_t tl_carrier_loss; u_int8_t acommit; }; /* * ACOMMIT register bits. These are used only when a bitrate * PHY is selected ('bitrate' bit in netconfig register is set). */ #define TL_AC_MTXER 0x01 /* reserved */ #define TL_AC_MTXD1 0x02 /* 0 == 10baseT 1 == AUI */ #define TL_AC_MTXD2 0x04 /* loopback disable */ #define TL_AC_MTXD3 0x08 /* full duplex disable */ /* * register space access macros */ #define CSR_WRITE_4(sc, reg, val) \ bus_space_write_4(sc->tl_btag, sc->tl_bhandle, reg, val) #define CSR_WRITE_2(sc, reg, val) \ bus_space_write_2(sc->tl_btag, sc->tl_bhandle, reg, val) #define CSR_WRITE_1(sc, reg, val) \ bus_space_write_1(sc->tl_btag, sc->tl_bhandle, reg, val) #define CSR_READ_4(sc, reg) \ bus_space_read_4(sc->tl_btag, sc->tl_bhandle, reg) #define CSR_READ_2(sc, reg) \ bus_space_read_2(sc->tl_btag, sc->tl_bhandle, reg) #define CSR_READ_1(sc, reg) \ bus_space_read_1(sc->tl_btag, sc->tl_bhandle, reg) #define CMD_PUT(sc, x) CSR_WRITE_4(sc, TL_HOSTCMD, x) #define CMD_SET(sc, x) \ CSR_WRITE_4(sc, TL_HOSTCMD, CSR_READ_4(sc, TL_HOSTCMD) | (x)) #define CMD_CLR(sc, x) \ CSR_WRITE_4(sc, TL_HOSTCMD, CSR_READ_4(sc, TL_HOSTCMD) & ~(x)) /* * ThunderLAN adapters typically have a serial EEPROM containing * configuration information. The main reason we're interested in * it is because it also contains the adapters's station address. * * Access to the EEPROM is a bit goofy since it is a serial device: * you have to do reads and writes one bit at a time. The state of * the DATA bit can only change while the CLOCK line is held low. * Transactions work basically like this: * * 1) Send the EEPROM_START sequence to prepare the EEPROM for * accepting commands. This pulls the clock high, sets * the data bit to 0, enables transmission to the EEPROM, * pulls the data bit up to 1, then pulls the clock low. * The idea is to do a 0 to 1 transition of the data bit * while the clock pin is held high. * * 2) To write a bit to the EEPROM, set the TXENABLE bit, then * set the EDATA bit to send a 1 or clear it to send a 0. * Finally, set and then clear ECLOK. Strobing the clock * transmits the bit. After 8 bits have been written, the * EEPROM should respond with an ACK, which should be read. * * 3) To read a bit from the EEPROM, clear the TXENABLE bit, * then set ECLOK. The bit can then be read by reading EDATA. * ECLOCK should then be cleared again. This can be repeated * 8 times to read a whole byte, after which the * * 4) We need to send the address byte to the EEPROM. For this * we have to send the write control byte to the EEPROM to * tell it to accept data. The byte is 0xA0. The EEPROM should * ack this. The address byte can be send after that. * * 5) Now we have to tell the EEPROM to send us data. For that we * have to transmit the read control byte, which is 0xA1. This * byte should also be acked. We can then read the data bits * from the EEPROM. * * 6) When we're all finished, send the EEPROM_STOP sequence. * * Note that we use the ThunderLAN's NetSio register to access the * EEPROM, however there is an alternate method. There is a PCI NVRAM * register at PCI offset 0xB4 which can also be used with minor changes. * The difference is that access to PCI registers via pci_conf_read() * and pci_conf_write() is done using programmed I/O, which we want to * avoid. */ /* * Note that EEPROM_START leaves transmission enabled. */ #define EEPROM_START \ tl_dio_setbit(sc, TL_NETSIO, TL_SIO_ECLOK); /* Pull clock pin high */\ tl_dio_setbit(sc, TL_NETSIO, TL_SIO_EDATA); /* Set DATA bit to 1 */ \ tl_dio_setbit(sc, TL_NETSIO, TL_SIO_ETXEN); /* Enable xmit to write bit */\ tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_EDATA); /* Pull DATA bit to 0 again */\ tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_ECLOK); /* Pull clock low again */ /* * EEPROM_STOP ends access to the EEPROM and clears the ETXEN bit so * that no further data can be written to the EEPROM I/O pin. */ #define EEPROM_STOP \ tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_ETXEN); /* Disable xmit */ \ tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_EDATA); /* Pull DATA to 0 */ \ tl_dio_setbit(sc, TL_NETSIO, TL_SIO_ECLOK); /* Pull clock high */ \ tl_dio_setbit(sc, TL_NETSIO, TL_SIO_ETXEN); /* Enable xmit */ \ tl_dio_setbit(sc, TL_NETSIO, TL_SIO_EDATA); /* Toggle DATA to 1 */ \ tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_ETXEN); /* Disable xmit. */ \ tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_ECLOK); /* Pull clock low again */ /* * These are the register definitions for the PHY (physical layer * interface chip). * The ThunderLAN chip has a built-in 10Mb/sec PHY which may be used * in some configurations. The Compaq 10/100 cards based on the ThunderLAN * use a National Semiconductor DP83840A PHY. The generic BMCR and BMSR * layouts for both PHYs are identical, however some of the bits are not * used by the ThunderLAN's internal PHY (most notably those dealing with * switching between 10 and 100Mb/sec speeds). Since Both PHYs use the * same bits, we #define them with generic names here. */ /* * PHY BMCR Basic Mode Control Register */ #define PHY_BMCR 0x00 #define PHY_BMCR_RESET 0x8000 #define PHY_BMCR_LOOPBK 0x4000 #define PHY_BMCR_SPEEDSEL 0x2000 #define PHY_BMCR_AUTONEGENBL 0x1000 #define PHY_BMCR_RSVD0 0x0800 /* write as zero */ #define PHY_BMCR_PWRDOWN 0x0800 /* tlan internal PHY only */ #define PHY_BMCR_ISOLATE 0x0400 #define PHY_BMCR_AUTONEGRSTR 0x0200 #define PHY_BMCR_DUPLEX 0x0100 #define PHY_BMCR_COLLTEST 0x0080 #define PHY_BMCR_RSVD1 0x0040 /* write as zero, don't care */ #define PHY_BMCR_RSVD2 0x0020 /* write as zero, don't care */ #define PHY_BMCR_RSVD3 0x0010 /* write as zero, don't care */ #define PHY_BMCR_RSVD4 0x0008 /* write as zero, don't care */ #define PHY_BMCR_RSVD5 0x0004 /* write as zero, don't care */ #define PHY_BMCR_RSVD6 0x0002 /* write as zero, don't care */ #define PHY_BMCR_RSVD7 0x0001 /* write as zero, don't care */ /* * RESET: 1 == software reset, 0 == normal operation * Resets status and control registers to default values. * Relatches all hardware config values. * * LOOPBK: 1 == loopback operation enabled, 0 == normal operation * * SPEEDSEL: 1 == 100Mb/s, 0 == 10Mb/s * Link speed is selected byt his bit or if auto-negotiation if bit * 12 (AUTONEGENBL) is set (in which case the value of this register * is ignored). * * AUTONEGENBL: 1 == Autonegotiation enabled, 0 == Autonegotiation disabled * Bits 8 and 13 are ignored when autoneg is set, otherwise bits 8 and 13 * determine speed and mode. Should be cleared and then set if PHY configured * for no autoneg on startup. * * ISOLATE: 1 == isolate PHY from MII, 0 == normal operation * * AUTONEGRSTR: 1 == restart autonegotiation, 0 = normal operation * * DUPLEX: 1 == full duplex mode, 0 == half duplex mode * * COLLTEST: 1 == collision test enabled, 0 == normal operation */ /* * PHY, BMSR Basic Mode Status Register */ #define PHY_BMSR 0x01 #define PHY_BMSR_100BT4 0x8000 #define PHY_BMSR_100BTXFULL 0x4000 #define PHY_BMSR_100BTXHALF 0x2000 #define PHY_BMSR_10BTFULL 0x1000 #define PHY_BMSR_10BTHALF 0x0800 #define PHY_BMSR_RSVD1 0x0400 /* write as zero, don't care */ #define PHY_BMSR_RSVD2 0x0200 /* write as zero, don't care */ #define PHY_BMSR_RSVD3 0x0100 /* write as zero, don't care */ #define PHY_BMSR_RSVD4 0x0080 /* write as zero, don't care */ #define PHY_BMSR_MFPRESUP 0x0040 #define PHY_BMSR_AUTONEGCOMP 0x0020 #define PHY_BMSR_REMFAULT 0x0010 #define PHY_BMSR_CANAUTONEG 0x0008 #define PHY_BMSR_LINKSTAT 0x0004 #define PHY_BMSR_JABBER 0x0002 #define PHY_BMSR_EXTENDED 0x0001 #define PHY_CTL_IGLINK 0x8000 #define PHY_CTL_SWAPOL 0x4000 #define PHY_CTL_AUISEL 0x2000 #define PHY_CTL_SQEEN 0x1000 #define PHY_CTL_MTEST 0x0800 #define PHY_CTL_NFEW 0x0004 #define PHY_CTL_INTEN 0x0002 #define PHY_CTL_TINT 0x0001 #define TL_PHY_GENCTL 0x00 #define TL_PHY_GENSTS 0x01 /* * PHY Generic Identifier Register, hi bits */ #define TL_PHY_VENID 0x02 /* * PHY Generic Identifier Register, lo bits */ #define TL_PHY_DEVID 0x03 #define TL_PHY_ANAR 0x04 #define TL_PHY_LPAR 0x05 #define TL_PHY_ANEXP 0x06 #define TL_PHY_PHYID 0x10 #define TL_PHY_CTL 0x11 #define TL_PHY_STS 0x12 #define TL_LPAR_RMFLT 0x2000 #define TL_LPAR_RSVD0 0x1000 #define TL_LPAR_RSVD1 0x0800 #define TL_LPAR_100BT4 0x0400 #define TL_LPAR_100BTXFULL 0x0200 #define TL_LPAR_100BTXHALF 0x0100 #define TL_LPAR_10BTFULL 0x0080 #define TL_LPAR_10BTHALF 0x0040 /* * PHY Antoneg advertisement register. */ #define PHY_ANAR TL_PHY_ANAR #define PHY_ANAR_NEXTPAGE 0x8000 #define PHY_ANAR_RSVD0 0x4000 #define PHY_ANAR_TLRFLT 0x2000 #define PHY_ANAR_RSVD1 0x1000 #define PHY_RSVD_RSDV2 0x0800 #define PHY_RSVD_RSVD3 0x0400 #define PHY_ANAR_100BT4 0x0200 #define PHY_ANAR_100BTXFULL 0x0100 #define PHY_ANAR_100BTXHALF 0x0080 #define PHY_ANAR_10BTFULL 0x0040 #define PHY_ANAR_10BTHALF 0x0020 #define PHY_ANAR_PROTO4 0x0010 #define PHY_ANAR_PROTO3 0x0008 #define PHY_ANAR_PROTO2 0x0004 #define PHY_AHAR_PROTO1 0x0002 #define PHY_AHAR_PROTO0 0x0001 /* * DP83840 PHY, PCS Confifguration Register */ #define TL_DP83840_PCS 0x17 #define TL_DP83840_PCS_LED4_MODE 0x0002 #define TL_DP83840_PCS_F_CONNECT 0x0020 #define TL_DP83840_PCS_BIT8 0x0100 #define TL_DP83840_PCS_BIT10 0x0400 /* * DP83840 PHY, PAR register */ #define TL_DP83840_PAR 0x19 #define PAR_RSVD0 0x8000 #define PAR_RSVD1 0x4000 #define PAR_RSVD2 0x2000 #define PAR_RSVD3 0x1000 #define PAR_DIS_CRS_JAB 0x0800 #define PAR_AN_EN_STAT 0x0400 #define PAR_RSVD4 0x0200 #define PAR_FEFI_EN 0x0100 #define PAR_DUPLEX_STAT 0x0080 #define PAR_SPEED_10 0x0040 #define PAR_CIM_STATUS 0x0020 #define PAR_PHYADDR4 0x0010 #define PAR_PHYADDR3 0x0008 #define PAR_PHYADDR2 0x0004 #define PAR_PHYADDR1 0x0002 #define PAR_PHYADDR0 0x0001 /* * Microchip Technology 24Cxx EEPROM control bytes */ #define EEPROM_CTL_READ 0xA1 /* 0101 0001 */ #define EEPROM_CTL_WRITE 0xA0 /* 0101 0000 */ #ifdef __alpha__ #undef vtophys #define vtophys(va) alpha_XXX_dmamap((vm_offset_t)va) #endif