/* $OpenBSD: if_wb.c,v 1.3 1999/09/27 18:17:01 jason Exp $ */ /* * Copyright (c) 1997, 1998 * Bill Paul . All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. All advertising materials mentioning features or use of this software * must display the following acknowledgement: * This product includes software developed by Bill Paul. * 4. Neither the name of the author nor the names of any co-contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF * THE POSSIBILITY OF SUCH DAMAGE. * * $FreeBSD: if_wb.c,v 1.13 1999/07/11 00:56:07 wpaul Exp $ */ /* * Winbond fast ethernet PCI NIC driver * * Supports various cheap network adapters based on the Winbond W89C840F * fast ethernet controller chip. This includes adapters manufactured by * Winbond itself and some made by Linksys. * * Written by Bill Paul * Electrical Engineering Department * Columbia University, New York City */ /* * The Winbond W89C840F chip is a bus master; in some ways it resembles * a DEC 'tulip' chip, only not as complicated. Unfortunately, it has * one major difference which is that while the registers do many of * the same things as a tulip adapter, the offsets are different: where * tulip registers are typically spaced 8 bytes apart, the Winbond * registers are spaced 4 bytes apart. The receiver filter is also * programmed differently. * * Like the tulip, the Winbond chip uses small descriptors containing * a status word, a control word and 32-bit areas that can either be used * to point to two external data blocks, or to point to a single block * and another descriptor in a linked list. Descriptors can be grouped * together in blocks to form fixed length rings or can be chained * together in linked lists. A single packet may be spread out over * several descriptors if necessary. * * For the receive ring, this driver uses a linked list of descriptors, * each pointing to a single mbuf cluster buffer, which us large enough * to hold an entire packet. The link list is looped back to created a * closed ring. * * For transmission, the driver creates a linked list of 'super descriptors' * which each contain several individual descriptors linked toghether. * Each 'super descriptor' contains WB_MAXFRAGS descriptors, which we * abuse as fragment pointers. This allows us to use a buffer managment * scheme very similar to that used in the ThunderLAN and Etherlink XL * drivers. * * Autonegotiation is performed using the external PHY via the MII bus. * The sample boards I have all use a Davicom PHY. * * Note: the author of the Linux driver for the Winbond chip alludes * to some sort of flaw in the chip's design that seems to mandate some * drastic workaround which signigicantly impairs transmit performance. * I have no idea what he's on about: transmit performance with all * three of my test boards seems fine. */ #include "bpfilter.h" #include #include #include #include #include #include #include #include #include #include #include #ifdef INET #include #include #include #include #include #endif #include #if NBPFILTER > 0 #include #endif #include /* for vtophys */ #include /* for vtophys */ #include #include #include #include #include #define WB_USEIOSPACE /* #define WB_BACKGROUND_AUTONEG */ #include /* * Various supported PHY vendors/types and their names. Note that * this driver will work with pretty much any MII-compliant PHY, * so failure to positively identify the chip is not a fatal error. */ struct wb_type wb_phys[] = { { TI_PHY_VENDORID, TI_PHY_10BT, "" }, { TI_PHY_VENDORID, TI_PHY_100VGPMI, "" }, { NS_PHY_VENDORID, NS_PHY_83840A, ""}, { LEVEL1_PHY_VENDORID, LEVEL1_PHY_LXT970, "" }, { INTEL_PHY_VENDORID, INTEL_PHY_82555, "" }, { SEEQ_PHY_VENDORID, SEEQ_PHY_80220, "" }, { 0, 0, "" } }; int wb_probe __P((struct device *, void *, void *)); void wb_attach __P((struct device *, struct device *, void *)); int wb_newbuf __P((struct wb_softc *, struct wb_chain_onefrag *, struct mbuf *)); int wb_encap __P((struct wb_softc *, struct wb_chain *, struct mbuf *)); void wb_rxeof __P((struct wb_softc *)); void wb_rxeoc __P((struct wb_softc *)); void wb_txeof __P((struct wb_softc *)); void wb_txeoc __P((struct wb_softc *)); int wb_intr __P((void *)); void wb_start __P((struct ifnet *)); int wb_ioctl __P((struct ifnet *, u_long, caddr_t)); void wb_init __P((void *)); void wb_stop __P((struct wb_softc *)); void wb_watchdog __P((struct ifnet *)); void wb_shutdown __P((void *)); int wb_ifmedia_upd __P((struct ifnet *)); void wb_ifmedia_sts __P((struct ifnet *, struct ifmediareq *)); void wb_eeprom_putbyte __P((struct wb_softc *, int)); void wb_eeprom_getword __P((struct wb_softc *, int, u_int16_t *)); void wb_read_eeprom __P((struct wb_softc *, caddr_t, int, int, int)); void wb_mii_sync __P((struct wb_softc *)); void wb_mii_send __P((struct wb_softc *, u_int32_t, int)); int wb_mii_readreg __P((struct wb_softc *, struct wb_mii_frame *)); int wb_mii_writereg __P((struct wb_softc *, struct wb_mii_frame *)); void wb_phy_writereg __P((struct wb_softc *, int, int)); u_int16_t wb_phy_readreg __P((struct wb_softc *, int)); void wb_autoneg_xmit __P((struct wb_softc *)); void wb_autoneg_mii __P((struct wb_softc *, int, int)); void wb_setmode_mii __P((struct wb_softc *, int)); void wb_getmode_mii __P((struct wb_softc *)); void wb_setcfg __P((struct wb_softc *, int)); u_int8_t wb_calchash __P((caddr_t)); void wb_setmulti __P((struct wb_softc *)); void wb_reset __P((struct wb_softc *)); int wb_list_rx_init __P((struct wb_softc *)); int wb_list_tx_init __P((struct wb_softc *)); #define WB_SETBIT(sc, reg, x) \ CSR_WRITE_4(sc, reg, \ CSR_READ_4(sc, reg) | x) #define WB_CLRBIT(sc, reg, x) \ CSR_WRITE_4(sc, reg, \ CSR_READ_4(sc, reg) & ~x) #define SIO_SET(x) \ CSR_WRITE_4(sc, WB_SIO, \ CSR_READ_4(sc, WB_SIO) | x) #define SIO_CLR(x) \ CSR_WRITE_4(sc, WB_SIO, \ CSR_READ_4(sc, WB_SIO) & ~x) /* * Send a read command and address to the EEPROM, check for ACK. */ void wb_eeprom_putbyte(sc, addr) struct wb_softc *sc; int addr; { register int d, i; d = addr | WB_EECMD_READ; /* * Feed in each bit and stobe the clock. */ for (i = 0x400; i; i >>= 1) { if (d & i) { SIO_SET(WB_SIO_EE_DATAIN); } else { SIO_CLR(WB_SIO_EE_DATAIN); } DELAY(100); SIO_SET(WB_SIO_EE_CLK); DELAY(150); SIO_CLR(WB_SIO_EE_CLK); DELAY(100); } return; } /* * Read a word of data stored in the EEPROM at address 'addr.' */ void wb_eeprom_getword(sc, addr, dest) struct wb_softc *sc; int addr; u_int16_t *dest; { register int i; u_int16_t word = 0; /* Enter EEPROM access mode. */ CSR_WRITE_4(sc, WB_SIO, WB_SIO_EESEL|WB_SIO_EE_CS); /* * Send address of word we want to read. */ wb_eeprom_putbyte(sc, addr); CSR_WRITE_4(sc, WB_SIO, WB_SIO_EESEL|WB_SIO_EE_CS); /* * Start reading bits from EEPROM. */ for (i = 0x8000; i; i >>= 1) { SIO_SET(WB_SIO_EE_CLK); DELAY(100); if (CSR_READ_4(sc, WB_SIO) & WB_SIO_EE_DATAOUT) word |= i; SIO_CLR(WB_SIO_EE_CLK); DELAY(100); } /* Turn off EEPROM access mode. */ CSR_WRITE_4(sc, WB_SIO, 0); *dest = word; return; } /* * Read a sequence of words from the EEPROM. */ void wb_read_eeprom(sc, dest, off, cnt, swap) struct wb_softc *sc; caddr_t dest; int off; int cnt; int swap; { int i; u_int16_t word = 0, *ptr; for (i = 0; i < cnt; i++) { wb_eeprom_getword(sc, off + i, &word); ptr = (u_int16_t *)(dest + (i * 2)); if (swap) *ptr = ntohs(word); else *ptr = word; } return; } /* * Sync the PHYs by setting data bit and strobing the clock 32 times. */ void wb_mii_sync(sc) struct wb_softc *sc; { register int i; SIO_SET(WB_SIO_MII_DIR|WB_SIO_MII_DATAIN); for (i = 0; i < 32; i++) { SIO_SET(WB_SIO_MII_CLK); DELAY(1); SIO_CLR(WB_SIO_MII_CLK); DELAY(1); } return; } /* * Clock a series of bits through the MII. */ void wb_mii_send(sc, bits, cnt) struct wb_softc *sc; u_int32_t bits; int cnt; { int i; SIO_CLR(WB_SIO_MII_CLK); for (i = (0x1 << (cnt - 1)); i; i >>= 1) { if (bits & i) { SIO_SET(WB_SIO_MII_DATAIN); } else { SIO_CLR(WB_SIO_MII_DATAIN); } DELAY(1); SIO_CLR(WB_SIO_MII_CLK); DELAY(1); SIO_SET(WB_SIO_MII_CLK); } } /* * Read an PHY register through the MII. */ int wb_mii_readreg(sc, frame) struct wb_softc *sc; struct wb_mii_frame *frame; { int i, ack, s; s = splimp(); /* * Set up frame for RX. */ frame->mii_stdelim = WB_MII_STARTDELIM; frame->mii_opcode = WB_MII_READOP; frame->mii_turnaround = 0; frame->mii_data = 0; CSR_WRITE_4(sc, WB_SIO, 0); /* * Turn on data xmit. */ SIO_SET(WB_SIO_MII_DIR); wb_mii_sync(sc); /* * Send command/address info. */ wb_mii_send(sc, frame->mii_stdelim, 2); wb_mii_send(sc, frame->mii_opcode, 2); wb_mii_send(sc, frame->mii_phyaddr, 5); wb_mii_send(sc, frame->mii_regaddr, 5); /* Idle bit */ SIO_CLR((WB_SIO_MII_CLK|WB_SIO_MII_DATAIN)); DELAY(1); SIO_SET(WB_SIO_MII_CLK); DELAY(1); /* Turn off xmit. */ SIO_CLR(WB_SIO_MII_DIR); /* Check for ack */ SIO_CLR(WB_SIO_MII_CLK); DELAY(1); SIO_SET(WB_SIO_MII_CLK); DELAY(1); ack = CSR_READ_4(sc, WB_SIO) & WB_SIO_MII_DATAOUT; SIO_CLR(WB_SIO_MII_CLK); DELAY(1); SIO_SET(WB_SIO_MII_CLK); DELAY(1); /* * Now try reading data bits. If the ack failed, we still * need to clock through 16 cycles to keep the PHY(s) in sync. */ if (ack) { for(i = 0; i < 16; i++) { SIO_CLR(WB_SIO_MII_CLK); DELAY(1); SIO_SET(WB_SIO_MII_CLK); DELAY(1); } goto fail; } for (i = 0x8000; i; i >>= 1) { SIO_CLR(WB_SIO_MII_CLK); DELAY(1); if (!ack) { if (CSR_READ_4(sc, WB_SIO) & WB_SIO_MII_DATAOUT) frame->mii_data |= i; DELAY(1); } SIO_SET(WB_SIO_MII_CLK); DELAY(1); } fail: SIO_CLR(WB_SIO_MII_CLK); DELAY(1); SIO_SET(WB_SIO_MII_CLK); DELAY(1); splx(s); if (ack) return(1); return(0); } /* * Write to a PHY register through the MII. */ int wb_mii_writereg(sc, frame) struct wb_softc *sc; struct wb_mii_frame *frame; { int s; s = splimp(); /* * Set up frame for TX. */ frame->mii_stdelim = WB_MII_STARTDELIM; frame->mii_opcode = WB_MII_WRITEOP; frame->mii_turnaround = WB_MII_TURNAROUND; /* * Turn on data output. */ SIO_SET(WB_SIO_MII_DIR); wb_mii_sync(sc); wb_mii_send(sc, frame->mii_stdelim, 2); wb_mii_send(sc, frame->mii_opcode, 2); wb_mii_send(sc, frame->mii_phyaddr, 5); wb_mii_send(sc, frame->mii_regaddr, 5); wb_mii_send(sc, frame->mii_turnaround, 2); wb_mii_send(sc, frame->mii_data, 16); /* Idle bit. */ SIO_SET(WB_SIO_MII_CLK); DELAY(1); SIO_CLR(WB_SIO_MII_CLK); DELAY(1); /* * Turn off xmit. */ SIO_CLR(WB_SIO_MII_DIR); splx(s); return(0); } u_int16_t wb_phy_readreg(sc, reg) struct wb_softc *sc; int reg; { struct wb_mii_frame frame; bzero((char *)&frame, sizeof(frame)); frame.mii_phyaddr = sc->wb_phy_addr; frame.mii_regaddr = reg; wb_mii_readreg(sc, &frame); return(frame.mii_data); } void wb_phy_writereg(sc, reg, data) struct wb_softc *sc; int reg; int data; { struct wb_mii_frame frame; bzero((char *)&frame, sizeof(frame)); frame.mii_phyaddr = sc->wb_phy_addr; frame.mii_regaddr = reg; frame.mii_data = data; wb_mii_writereg(sc, &frame); return; } u_int8_t wb_calchash(addr) caddr_t addr; { u_int32_t crc, carry; int i, j; u_int8_t c; /* Compute CRC for the address value. */ crc = 0xFFFFFFFF; /* initial value */ for (i = 0; i < 6; i++) { c = *(addr + i); for (j = 0; j < 8; j++) { carry = ((crc & 0x80000000) ? 1 : 0) ^ (c & 0x01); crc <<= 1; c >>= 1; if (carry) crc = (crc ^ 0x04c11db6) | carry; } } /* * return the filter bit position * Note: I arrived at the following nonsense * through experimentation. It's not the usual way to * generate the bit position but it's the only thing * I could come up with that works. */ return(~(crc >> 26) & 0x0000003F); } /* * Program the 64-bit multicast hash filter. */ void wb_setmulti(sc) struct wb_softc *sc; { struct ifnet *ifp; int h = 0; u_int32_t hashes[2] = { 0, 0 }; struct arpcom *ac = &sc->arpcom; struct ether_multi *enm; struct ether_multistep step; u_int32_t rxfilt; int mcnt = 0; ifp = &sc->arpcom.ac_if; rxfilt = CSR_READ_4(sc, WB_NETCFG); if (ifp->if_flags & IFF_ALLMULTI || ifp->if_flags & IFF_PROMISC) { rxfilt |= WB_NETCFG_RX_MULTI; CSR_WRITE_4(sc, WB_NETCFG, rxfilt); CSR_WRITE_4(sc, WB_MAR0, 0xFFFFFFFF); CSR_WRITE_4(sc, WB_MAR1, 0xFFFFFFFF); return; } /* first, zot all the existing hash bits */ CSR_WRITE_4(sc, WB_MAR0, 0); CSR_WRITE_4(sc, WB_MAR1, 0); /* now program new ones */ ETHER_FIRST_MULTI(step, ac, enm); while (enm != NULL) { h = wb_calchash(enm->enm_addrlo); if (h < 32) hashes[0] |= (1 << h); else hashes[1] |= (1 << (h - 32)); mcnt++; ETHER_NEXT_MULTI(step, enm); } if (mcnt) rxfilt |= WB_NETCFG_RX_MULTI; else rxfilt &= ~WB_NETCFG_RX_MULTI; CSR_WRITE_4(sc, WB_MAR0, hashes[0]); CSR_WRITE_4(sc, WB_MAR1, hashes[1]); CSR_WRITE_4(sc, WB_NETCFG, rxfilt); return; } /* * Initiate an autonegotiation session. */ void wb_autoneg_xmit(sc) struct wb_softc *sc; { u_int16_t phy_sts; wb_phy_writereg(sc, PHY_BMCR, PHY_BMCR_RESET); DELAY(500); while(wb_phy_readreg(sc, PHY_BMCR) & PHY_BMCR_RESET); phy_sts = wb_phy_readreg(sc, PHY_BMCR); phy_sts |= PHY_BMCR_AUTONEGENBL|PHY_BMCR_AUTONEGRSTR; wb_phy_writereg(sc, PHY_BMCR, phy_sts); return; } /* * Invoke autonegotiation on a PHY. */ void wb_autoneg_mii(sc, flag, verbose) struct wb_softc *sc; int flag; int verbose; { u_int16_t phy_sts = 0, media, advert, ability; struct ifnet *ifp; struct ifmedia *ifm; ifm = &sc->ifmedia; ifp = &sc->arpcom.ac_if; ifm->ifm_media = IFM_ETHER | IFM_AUTO; /* * The 100baseT4 PHY on the 3c905-T4 has the 'autoneg supported' * bit cleared in the status register, but has the 'autoneg enabled' * bit set in the control register. This is a contradiction, and * I'm not sure how to handle it. If you want to force an attempt * to autoneg for 100baseT4 PHYs, #define FORCE_AUTONEG_TFOUR * and see what happens. */ #ifndef FORCE_AUTONEG_TFOUR /* * First, see if autoneg is supported. If not, there's * no point in continuing. */ phy_sts = wb_phy_readreg(sc, PHY_BMSR); if (!(phy_sts & PHY_BMSR_CANAUTONEG)) { if (verbose) printf("%s: autonegotiation not supported\n", sc->sc_dev.dv_xname); ifm->ifm_media = IFM_ETHER|IFM_10_T|IFM_HDX; return; } #endif switch (flag) { case WB_FLAG_FORCEDELAY: /* * XXX Never use this option anywhere but in the probe * routine: making the kernel stop dead in its tracks * for three whole seconds after we've gone multi-user * is really bad manners. */ wb_autoneg_xmit(sc); DELAY(5000000); break; case WB_FLAG_SCHEDDELAY: /* * Wait for the transmitter to go idle before starting * an autoneg session, otherwise wb_start() may clobber * our timeout, and we don't want to allow transmission * during an autoneg session since that can screw it up. */ if (sc->wb_cdata.wb_tx_head != NULL) { sc->wb_want_auto = 1; return; } wb_autoneg_xmit(sc); ifp->if_timer = 5; sc->wb_autoneg = 1; sc->wb_want_auto = 0; return; break; case WB_FLAG_DELAYTIMEO: ifp->if_timer = 0; sc->wb_autoneg = 0; break; default: printf("%s: invalid autoneg flag: %d\n", sc->sc_dev.dv_xname, flag); return; } if (wb_phy_readreg(sc, PHY_BMSR) & PHY_BMSR_AUTONEGCOMP) { if (verbose) printf("%s: autoneg complete, ", sc->sc_dev.dv_xname); phy_sts = wb_phy_readreg(sc, PHY_BMSR); } else { if (verbose) printf("%s: autoneg not complete, ", sc->sc_dev.dv_xname); } media = wb_phy_readreg(sc, PHY_BMCR); /* Link is good. Report modes and set duplex mode. */ if (wb_phy_readreg(sc, PHY_BMSR) & PHY_BMSR_LINKSTAT) { if (verbose) printf("link status good "); advert = wb_phy_readreg(sc, PHY_ANAR); ability = wb_phy_readreg(sc, PHY_LPAR); if (advert & PHY_ANAR_100BT4 && ability & PHY_ANAR_100BT4) { ifm->ifm_media = IFM_ETHER|IFM_100_T4; media |= PHY_BMCR_SPEEDSEL; media &= ~PHY_BMCR_DUPLEX; printf("(100baseT4)\n"); } else if (advert & PHY_ANAR_100BTXFULL && ability & PHY_ANAR_100BTXFULL) { ifm->ifm_media = IFM_ETHER|IFM_100_TX|IFM_FDX; media |= PHY_BMCR_SPEEDSEL; media |= PHY_BMCR_DUPLEX; printf("(full-duplex, 100Mbps)\n"); } else if (advert & PHY_ANAR_100BTXHALF && ability & PHY_ANAR_100BTXHALF) { ifm->ifm_media = IFM_ETHER|IFM_100_TX|IFM_HDX; media |= PHY_BMCR_SPEEDSEL; media &= ~PHY_BMCR_DUPLEX; printf("(half-duplex, 100Mbps)\n"); } else if (advert & PHY_ANAR_10BTFULL && ability & PHY_ANAR_10BTFULL) { ifm->ifm_media = IFM_ETHER|IFM_10_T|IFM_FDX; media &= ~PHY_BMCR_SPEEDSEL; media |= PHY_BMCR_DUPLEX; printf("(full-duplex, 10Mbps)\n"); } else /* if (advert & PHY_ANAR_10BTHALF && ability & PHY_ANAR_10BTHALF) */ { ifm->ifm_media = IFM_ETHER|IFM_10_T|IFM_HDX; media &= ~PHY_BMCR_SPEEDSEL; media &= ~PHY_BMCR_DUPLEX; printf("(half-duplex, 10Mbps)\n"); } media &= ~PHY_BMCR_AUTONEGENBL; /* Set ASIC's duplex mode to match the PHY. */ wb_setcfg(sc, media); wb_phy_writereg(sc, PHY_BMCR, media); } else { if (verbose) printf("no carrier\n"); } if (flag != WB_FLAG_FORCEDELAY) wb_init(sc); if (sc->wb_tx_pend) { sc->wb_autoneg = 0; sc->wb_tx_pend = 0; wb_start(ifp); } return; } void wb_getmode_mii(sc) struct wb_softc *sc; { u_int16_t bmsr; struct ifnet *ifp; ifp = &sc->arpcom.ac_if; bmsr = wb_phy_readreg(sc, PHY_BMSR); /* fallback */ sc->ifmedia.ifm_media = IFM_ETHER|IFM_10_T|IFM_HDX; if (bmsr & PHY_BMSR_10BTHALF) { ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_10_T|IFM_HDX, 0, NULL); ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_10_T, 0, NULL); } if (bmsr & PHY_BMSR_10BTFULL) { ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_10_T|IFM_FDX, 0, NULL); sc->ifmedia.ifm_media = IFM_ETHER|IFM_10_T|IFM_FDX; } if (bmsr & PHY_BMSR_100BTXHALF) { ifp->if_baudrate = 100000000; ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_100_TX, 0, NULL); ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_100_TX|IFM_HDX, 0, NULL); sc->ifmedia.ifm_media = IFM_ETHER|IFM_100_TX|IFM_HDX; } if (bmsr & PHY_BMSR_100BTXFULL) { ifp->if_baudrate = 100000000; ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_100_TX|IFM_FDX, 0, NULL); sc->ifmedia.ifm_media = IFM_ETHER|IFM_100_TX|IFM_FDX; } /* Some also support 100BaseT4. */ if (bmsr & PHY_BMSR_100BT4) { ifp->if_baudrate = 100000000; ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_100_T4, 0, NULL); sc->ifmedia.ifm_media = IFM_ETHER|IFM_100_T4; #ifdef FORCE_AUTONEG_TFOUR ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_AUTO, 0 NULL): sc->ifmedia.ifm_media = IFM_ETHER|IFM_AUTO; #endif } if (bmsr & PHY_BMSR_CANAUTONEG) { ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_AUTO, 0, NULL); sc->ifmedia.ifm_media = IFM_ETHER|IFM_AUTO; } return; } /* * Set speed and duplex mode. */ void wb_setmode_mii(sc, media) struct wb_softc *sc; int media; { u_int16_t bmcr; struct ifnet *ifp; ifp = &sc->arpcom.ac_if; /* * If an autoneg session is in progress, stop it. */ if (sc->wb_autoneg) { printf("%s: canceling autoneg session\n", sc->sc_dev.dv_xname); ifp->if_timer = sc->wb_autoneg = sc->wb_want_auto = 0; bmcr = wb_phy_readreg(sc, PHY_BMCR); bmcr &= ~PHY_BMCR_AUTONEGENBL; wb_phy_writereg(sc, PHY_BMCR, bmcr); } printf("%s: selecting MII, ", sc->sc_dev.dv_xname); bmcr = wb_phy_readreg(sc, PHY_BMCR); bmcr &= ~(PHY_BMCR_AUTONEGENBL|PHY_BMCR_SPEEDSEL| PHY_BMCR_DUPLEX|PHY_BMCR_LOOPBK); if (IFM_SUBTYPE(media) == IFM_100_T4) { printf("100Mbps/T4, half-duplex\n"); bmcr |= PHY_BMCR_SPEEDSEL; bmcr &= ~PHY_BMCR_DUPLEX; } if (IFM_SUBTYPE(media) == IFM_100_TX) { printf("100Mbps, "); bmcr |= PHY_BMCR_SPEEDSEL; } if (IFM_SUBTYPE(media) == IFM_10_T) { printf("10Mbps, "); bmcr &= ~PHY_BMCR_SPEEDSEL; } if ((media & IFM_GMASK) == IFM_FDX) { printf("full duplex\n"); bmcr |= PHY_BMCR_DUPLEX; } else { printf("half duplex\n"); bmcr &= ~PHY_BMCR_DUPLEX; } wb_setcfg(sc, bmcr); wb_phy_writereg(sc, PHY_BMCR, bmcr); return; } /* * The Winbond manual states that in order to fiddle with the * 'full-duplex' and '100Mbps' bits in the netconfig register, we * first have to put the transmit and/or receive logic in the idle state. */ void wb_setcfg(sc, bmcr) struct wb_softc *sc; int bmcr; { int i, restart = 0; if (CSR_READ_4(sc, WB_NETCFG) & (WB_NETCFG_TX_ON|WB_NETCFG_RX_ON)) { restart = 1; WB_CLRBIT(sc, WB_NETCFG, (WB_NETCFG_TX_ON|WB_NETCFG_RX_ON)); for (i = 0; i < WB_TIMEOUT; i++) { DELAY(10); if ((CSR_READ_4(sc, WB_ISR) & WB_ISR_TX_IDLE) && (CSR_READ_4(sc, WB_ISR) & WB_ISR_RX_IDLE)) break; } if (i == WB_TIMEOUT) printf("%s: failed to force tx and " "rx to idle state\n", sc->sc_dev.dv_xname); } if (bmcr & PHY_BMCR_SPEEDSEL) WB_SETBIT(sc, WB_NETCFG, WB_NETCFG_100MBPS); else WB_CLRBIT(sc, WB_NETCFG, WB_NETCFG_100MBPS); if (bmcr & PHY_BMCR_DUPLEX) WB_SETBIT(sc, WB_NETCFG, WB_NETCFG_FULLDUPLEX); else WB_CLRBIT(sc, WB_NETCFG, WB_NETCFG_FULLDUPLEX); if (restart) WB_SETBIT(sc, WB_NETCFG, WB_NETCFG_TX_ON|WB_NETCFG_RX_ON); return; } void wb_reset(sc) struct wb_softc *sc; { register int i; WB_SETBIT(sc, WB_BUSCTL, WB_BUSCTL_RESET); for (i = 0; i < WB_TIMEOUT; i++) { DELAY(10); if (!(CSR_READ_4(sc, WB_BUSCTL) & WB_BUSCTL_RESET)) break; } if (i == WB_TIMEOUT) printf("%s: reset never completed!\n", sc->sc_dev.dv_xname); /* Wait a little while for the chip to get its brains in order. */ DELAY(1000); /* Reset the damn PHY too. */ if (sc->wb_pinfo != NULL) wb_phy_writereg(sc, PHY_BMCR, PHY_BMCR_RESET); return; } /* * Probe for a Winbond chip. Check the PCI vendor and device * IDs against our list and return a device name if we find a match. */ int wb_probe(parent, match, aux) struct device *parent; void *match, *aux; { struct pci_attach_args *pa = (struct pci_attach_args *)aux; if (PCI_VENDOR(pa->pa_id) == PCI_VENDOR_WINBOND) { switch (PCI_PRODUCT(pa->pa_id)) { case PCI_PRODUCT_WINBOND_W89C840F: return (1); } } if (PCI_VENDOR(pa->pa_id) == PCI_VENDOR_COMPEX) { switch (PCI_PRODUCT(pa->pa_id)) { case PCI_PRODUCT_COMPEX_RL100ATX: return (1); } } return (0); } /* * Attach the interface. Allocate softc structures, do ifmedia * setup and ethernet/BPF attach. */ void wb_attach(parent, self, aux) struct device *parent, *self; void *aux; { struct wb_softc *sc = (struct wb_softc *)self; struct pci_attach_args *pa = aux; pci_chipset_tag_t pc = pa->pa_pc; pci_intr_handle_t ih; const char *intrstr = NULL; struct ifnet *ifp = &sc->arpcom.ac_if; bus_addr_t iobase; bus_size_t iosize; int i, media = IFM_ETHER|IFM_100_TX|IFM_FDX, s; u_int round; caddr_t roundptr; u_int16_t phy_vid, phy_did, phy_sts; struct wb_type *p; u_int32_t command; s = splimp(); /* * Handle power management nonsense. */ command = pci_conf_read(pc, pa->pa_tag, WB_PCI_CAPID) & 0x000000FF; if (command == 0x01) { command = pci_conf_read(pc, pa->pa_tag, WB_PCI_PWRMGMTCTRL); if (command & WB_PSTATE_MASK) { u_int32_t io, mem, irq; /* Save important PCI config data. */ io = pci_conf_read(pc, pa->pa_tag, WB_PCI_LOIO); mem = pci_conf_read(pc, pa->pa_tag, WB_PCI_LOMEM); irq = pci_conf_read(pc, pa->pa_tag, WB_PCI_INTLINE); /* Reset the power state. */ printf("%s: chip is in D%d power mode " "-- setting to D0\n", sc->sc_dev.dv_xname, command & WB_PSTATE_MASK); command &= 0xFFFFFFFC; pci_conf_write(pc, pa->pa_tag, WB_PCI_PWRMGMTCTRL, command); /* Restore PCI config data. */ pci_conf_write(pc, pa->pa_tag, WB_PCI_LOIO, io); pci_conf_write(pc, pa->pa_tag, WB_PCI_LOMEM, mem); pci_conf_write(pc, pa->pa_tag, WB_PCI_INTLINE, irq); } } /* * Map control/status registers. */ command = pci_conf_read(pc, pa->pa_tag, PCI_COMMAND_STATUS_REG); command |= PCI_COMMAND_IO_ENABLE | PCI_COMMAND_MEM_ENABLE | PCI_COMMAND_MASTER_ENABLE; pci_conf_write(pc, pa->pa_tag, PCI_COMMAND_STATUS_REG, command); command = pci_conf_read(pc, pa->pa_tag, PCI_COMMAND_STATUS_REG); #ifdef WB_USEIOSPACE if (!(command & PCI_COMMAND_IO_ENABLE)) { printf(": failed to enable I/O ports!\n"); goto fail; } if (pci_io_find(pc, pa->pa_tag, WB_PCI_LOIO, &iobase, &iosize)) { printf(": can't find i/o space\n"); goto fail; } if (bus_space_map(pa->pa_iot, iobase, iosize, 0, &sc->wb_bhandle)) { printf(": can't map i/o space\n"); goto fail; } sc->wb_btag = pa->pa_iot; #else if (!(command & PCI_COMMAND_MEM_ENABLE)) { printf(": failed to enable memory mapping!\n"); goto fail; } if (pci_mem_find(pc, pa->pa_tag, WB_PCI_LOMEM, &iobase, &iosize, NULL)){ printf(": can't find mem space\n"); goto fail; } if (bus_space_map(pa->pa_memt, iobase, iosize, 0, &sc->wb_bhandle)) { printf(": can't map mem space\n"); goto fail; } sc->wb_btag = pa->pa_memt; #endif /* Allocate interrupt */ if (pci_intr_map(pc, pa->pa_intrtag, pa->pa_intrpin, pa->pa_intrline, &ih)) { printf(": couldn't map interrupt\n"); goto fail; } intrstr = pci_intr_string(pc, ih); sc->sc_ih = pci_intr_establish(pc, ih, IPL_NET, wb_intr, sc, self->dv_xname); if (sc->sc_ih == NULL) { printf(": couldn't establish interrupt"); if (intrstr != NULL) printf(" at %s", intrstr); printf("\n"); goto fail; } printf(": %s", intrstr); /* Reset the adapter. */ wb_reset(sc); /* * Get station address from the EEPROM. */ wb_read_eeprom(sc, (caddr_t)&sc->arpcom.ac_enaddr, 0, 3, 0); printf(" address %s\n", ether_sprintf(sc->arpcom.ac_enaddr)); sc->wb_ldata_ptr = malloc(sizeof(struct wb_list_data) + 8, M_DEVBUF, M_NOWAIT); if (sc->wb_ldata_ptr == NULL) { printf("%s: no memory for list buffers!\n",sc->sc_dev.dv_xname); goto fail; } sc->wb_ldata = (struct wb_list_data *)sc->wb_ldata_ptr; #ifdef __alpha__ round = (u_int64_t)sc->wb_ldata_ptr & 0xF; #endif #ifdef __i386__ round = (u_int32_t)sc->wb_ldata_ptr & 0xF; #endif roundptr = sc->wb_ldata_ptr; for (i = 0; i < 8; i++) { if (round % 8) { round++; roundptr++; } else break; } sc->wb_ldata = (struct wb_list_data *)roundptr; bzero(sc->wb_ldata, sizeof(struct wb_list_data)); ifp->if_softc = sc; ifp->if_mtu = ETHERMTU; ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_MULTICAST; ifp->if_ioctl = wb_ioctl; ifp->if_output = ether_output; ifp->if_start = wb_start; ifp->if_watchdog = wb_watchdog; ifp->if_baudrate = 10000000; ifp->if_snd.ifq_maxlen = WB_TX_LIST_CNT - 1; bcopy(sc->sc_dev.dv_xname, ifp->if_xname, IFNAMSIZ); for (i = WB_PHYADDR_MIN; i < WB_PHYADDR_MAX + 1; i++) { sc->wb_phy_addr = i; wb_phy_writereg(sc, PHY_BMCR, PHY_BMCR_RESET); DELAY(500); while(wb_phy_readreg(sc, PHY_BMCR) & PHY_BMCR_RESET); if ((phy_sts = wb_phy_readreg(sc, PHY_BMSR))) break; } if (phy_sts) { phy_vid = wb_phy_readreg(sc, PHY_VENID); phy_did = wb_phy_readreg(sc, PHY_DEVID); p = wb_phys; while(p->wb_vid) { if (phy_vid == p->wb_vid && (phy_did | 0x000F) == p->wb_did) { sc->wb_pinfo = p; break; } p++; } if (sc->wb_pinfo == NULL) sc->wb_pinfo = &wb_phys[PHY_UNKNOWN]; } else { printf("%s: MII without any phy!\n", sc->sc_dev.dv_xname); goto fail; } /* * Do ifmedia setup. */ ifmedia_init(&sc->ifmedia, 0, wb_ifmedia_upd, wb_ifmedia_sts); wb_getmode_mii(sc); wb_autoneg_mii(sc, WB_FLAG_FORCEDELAY, 1); media = sc->ifmedia.ifm_media; wb_stop(sc); ifmedia_set(&sc->ifmedia, media); /* * Call MI attach routines. */ if_attach(ifp); ether_ifattach(ifp); #if NBPFILTER > 0 bpfattach(&sc->arpcom.ac_if.if_bpf, ifp, DLT_EN10MB, sizeof(struct ether_header)); #endif shutdownhook_establish(wb_shutdown, sc); fail: splx(s); return; } /* * Initialize the transmit descriptors. */ int wb_list_tx_init(sc) struct wb_softc *sc; { struct wb_chain_data *cd; struct wb_list_data *ld; int i; cd = &sc->wb_cdata; ld = sc->wb_ldata; for (i = 0; i < WB_TX_LIST_CNT; i++) { cd->wb_tx_chain[i].wb_ptr = &ld->wb_tx_list[i]; if (i == (WB_TX_LIST_CNT - 1)) { cd->wb_tx_chain[i].wb_nextdesc = &cd->wb_tx_chain[0]; } else { cd->wb_tx_chain[i].wb_nextdesc = &cd->wb_tx_chain[i + 1]; } } cd->wb_tx_free = &cd->wb_tx_chain[0]; cd->wb_tx_tail = cd->wb_tx_head = NULL; return(0); } /* * Initialize the RX descriptors and allocate mbufs for them. Note that * we arrange the descriptors in a closed ring, so that the last descriptor * points back to the first. */ int wb_list_rx_init(sc) struct wb_softc *sc; { struct wb_chain_data *cd; struct wb_list_data *ld; int i; cd = &sc->wb_cdata; ld = sc->wb_ldata; for (i = 0; i < WB_RX_LIST_CNT; i++) { cd->wb_rx_chain[i].wb_ptr = (struct wb_desc *)&ld->wb_rx_list[i]; if (wb_newbuf(sc, &cd->wb_rx_chain[i], NULL) == ENOBUFS) return(ENOBUFS); if (i == (WB_RX_LIST_CNT - 1)) { cd->wb_rx_chain[i].wb_nextdesc = &cd->wb_rx_chain[0]; ld->wb_rx_list[i].wb_next = vtophys(&ld->wb_rx_list[0]); } else { cd->wb_rx_chain[i].wb_nextdesc = &cd->wb_rx_chain[i + 1]; ld->wb_rx_list[i].wb_next = vtophys(&ld->wb_rx_list[i + 1]); } } cd->wb_rx_head = &cd->wb_rx_chain[0]; return(0); } /* * Initialize an RX descriptor and attach an MBUF cluster. */ int wb_newbuf(sc, c, m) struct wb_softc *sc; struct wb_chain_onefrag *c; struct mbuf *m; { struct mbuf *m_new = NULL; if (m == NULL) { MGETHDR(m_new, M_DONTWAIT, MT_DATA); if (m_new == NULL) return(ENOBUFS); MCLGET(m_new, M_DONTWAIT); if (!(m_new->m_flags & M_EXT)) { m_freem(m_new); return(ENOBUFS); } m_new->m_len = m_new->m_pkthdr.len = MCLBYTES; } else { m_new = m; m_new->m_len = m_new->m_pkthdr.len = MCLBYTES; m_new->m_data = m_new->m_ext.ext_buf; } m_adj(m_new, sizeof(u_int64_t)); c->wb_mbuf = m_new; c->wb_ptr->wb_data = vtophys(mtod(m_new, caddr_t)); c->wb_ptr->wb_ctl = WB_RXCTL_RLINK | (MCLBYTES - 1); c->wb_ptr->wb_status = WB_RXSTAT; return(0); } /* * A frame has been uploaded: pass the resulting mbuf chain up to * the higher level protocols. */ void wb_rxeof(sc) struct wb_softc *sc; { struct ether_header *eh; struct mbuf *m; struct ifnet *ifp; struct wb_chain_onefrag *cur_rx; int total_len = 0; u_int32_t rxstat; ifp = &sc->arpcom.ac_if; while(!((rxstat = sc->wb_cdata.wb_rx_head->wb_ptr->wb_status) & WB_RXSTAT_OWN)) { struct mbuf *m0 = NULL; cur_rx = sc->wb_cdata.wb_rx_head; sc->wb_cdata.wb_rx_head = cur_rx->wb_nextdesc; m = cur_rx->wb_mbuf; if ((rxstat & WB_RXSTAT_MIIERR) || WB_RXBYTES(cur_rx->wb_ptr->wb_status) == 0) { ifp->if_ierrors++; wb_reset(sc); printf("%s: receiver babbling: possible chip " "bug, forcing reset\n", sc->sc_dev.dv_xname); ifp->if_flags |= IFF_OACTIVE; ifp->if_timer = 2; return; } if (rxstat & WB_RXSTAT_RXERR) { ifp->if_ierrors++; wb_newbuf(sc, cur_rx, m); continue; } /* No errors; receive the packet. */ total_len = WB_RXBYTES(cur_rx->wb_ptr->wb_status); /* * XXX The Winbond chip includes the CRC with every * received frame, and there's no way to turn this * behavior off (at least, I can't find anything in * the manual that explains how to do it) so we have * to trim off the CRC manually. */ total_len -= ETHER_CRC_LEN; m0 = m_devget(mtod(m, char *) - ETHER_ALIGN, total_len + ETHER_ALIGN, 0, ifp, NULL); wb_newbuf(sc, cur_rx, m); if (m0 == NULL) { ifp->if_ierrors++; continue; } m_adj(m0, ETHER_ALIGN); m = m0; ifp->if_ipackets++; eh = mtod(m, struct ether_header *); #if NBPFILTER > 0 /* * Handle BPF listeners. Let the BPF user see the packet. */ if (ifp->if_bpf) bpf_mtap(ifp->if_bpf, m); #endif /* Remove header from mbuf and pass it on. */ m_adj(m, sizeof(struct ether_header)); ether_input(ifp, eh, m); } return; } void wb_rxeoc(sc) struct wb_softc *sc; { wb_rxeof(sc); WB_CLRBIT(sc, WB_NETCFG, WB_NETCFG_RX_ON); CSR_WRITE_4(sc, WB_RXADDR, vtophys(&sc->wb_ldata->wb_rx_list[0])); WB_SETBIT(sc, WB_NETCFG, WB_NETCFG_RX_ON); if (CSR_READ_4(sc, WB_ISR) & WB_RXSTATE_SUSPEND) CSR_WRITE_4(sc, WB_RXSTART, 0xFFFFFFFF); return; } /* * A frame was downloaded to the chip. It's safe for us to clean up * the list buffers. */ void wb_txeof(sc) struct wb_softc *sc; { struct wb_chain *cur_tx; struct ifnet *ifp; ifp = &sc->arpcom.ac_if; /* Clear the timeout timer. */ ifp->if_timer = 0; if (sc->wb_cdata.wb_tx_head == NULL) return; /* * Go through our tx list and free mbufs for those * frames that have been transmitted. */ while(sc->wb_cdata.wb_tx_head->wb_mbuf != NULL) { u_int32_t txstat; cur_tx = sc->wb_cdata.wb_tx_head; txstat = WB_TXSTATUS(cur_tx); if ((txstat & WB_TXSTAT_OWN) || txstat == WB_UNSENT) break; if (txstat & WB_TXSTAT_TXERR) { ifp->if_oerrors++; if (txstat & WB_TXSTAT_ABORT) ifp->if_collisions++; if (txstat & WB_TXSTAT_LATECOLL) ifp->if_collisions++; } ifp->if_collisions += (txstat & WB_TXSTAT_COLLCNT) >> 3; ifp->if_opackets++; m_freem(cur_tx->wb_mbuf); cur_tx->wb_mbuf = NULL; if (sc->wb_cdata.wb_tx_head == sc->wb_cdata.wb_tx_tail) { sc->wb_cdata.wb_tx_head = NULL; sc->wb_cdata.wb_tx_tail = NULL; break; } sc->wb_cdata.wb_tx_head = cur_tx->wb_nextdesc; } return; } /* * TX 'end of channel' interrupt handler. */ void wb_txeoc(sc) struct wb_softc *sc; { struct ifnet *ifp; ifp = &sc->arpcom.ac_if; ifp->if_timer = 0; if (sc->wb_cdata.wb_tx_head == NULL) { ifp->if_flags &= ~IFF_OACTIVE; sc->wb_cdata.wb_tx_tail = NULL; if (sc->wb_want_auto) wb_autoneg_mii(sc, WB_FLAG_SCHEDDELAY, 1); } else { if (WB_TXOWN(sc->wb_cdata.wb_tx_head) == WB_UNSENT) { WB_TXOWN(sc->wb_cdata.wb_tx_head) = WB_TXSTAT_OWN; ifp->if_timer = 5; CSR_WRITE_4(sc, WB_TXSTART, 0xFFFFFFFF); } } return; } int wb_intr(arg) void *arg; { struct wb_softc *sc; struct ifnet *ifp; u_int32_t status; int r = 0; sc = arg; ifp = &sc->arpcom.ac_if; if (!(ifp->if_flags & IFF_UP)) return (r); /* Disable interrupts. */ CSR_WRITE_4(sc, WB_IMR, 0x00000000); for (;;) { status = CSR_READ_4(sc, WB_ISR); if (status) CSR_WRITE_4(sc, WB_ISR, status); if ((status & WB_INTRS) == 0) break; r = 1; if (status & WB_ISR_RX_OK) wb_rxeof(sc); if (status & WB_ISR_RX_IDLE) wb_rxeoc(sc); if ((status & WB_ISR_RX_NOBUF) || (status & WB_ISR_RX_ERR)) { ifp->if_ierrors++; #ifdef foo wb_stop(sc); wb_reset(sc); wb_init(sc); #endif } if (status & WB_ISR_TX_OK) wb_txeof(sc); if (status & WB_ISR_TX_NOBUF) wb_txeoc(sc); if (status & WB_ISR_TX_IDLE) { wb_txeof(sc); if (sc->wb_cdata.wb_tx_head != NULL) { WB_SETBIT(sc, WB_NETCFG, WB_NETCFG_TX_ON); CSR_WRITE_4(sc, WB_TXSTART, 0xFFFFFFFF); } } if (status & WB_ISR_TX_UNDERRUN) { ifp->if_oerrors++; wb_txeof(sc); WB_CLRBIT(sc, WB_NETCFG, WB_NETCFG_TX_ON); /* Jack up TX threshold */ sc->wb_txthresh += WB_TXTHRESH_CHUNK; WB_CLRBIT(sc, WB_NETCFG, WB_NETCFG_TX_THRESH); WB_SETBIT(sc, WB_NETCFG, WB_TXTHRESH(sc->wb_txthresh)); WB_SETBIT(sc, WB_NETCFG, WB_NETCFG_TX_ON); } if (status & WB_ISR_BUS_ERR) { wb_reset(sc); wb_init(sc); } } /* Re-enable interrupts. */ CSR_WRITE_4(sc, WB_IMR, WB_INTRS); if (ifp->if_snd.ifq_head != NULL) { wb_start(ifp); } return (r); } /* * Encapsulate an mbuf chain in a descriptor by coupling the mbuf data * pointers to the fragment pointers. */ int wb_encap(sc, c, m_head) struct wb_softc *sc; struct wb_chain *c; struct mbuf *m_head; { int frag = 0; struct wb_desc *f = NULL; int total_len; struct mbuf *m; /* * Start packing the mbufs in this chain into * the fragment pointers. Stop when we run out * of fragments or hit the end of the mbuf chain. */ m = m_head; total_len = 0; for (m = m_head, frag = 0; m != NULL; m = m->m_next) { if (m->m_len != 0) { if (frag == WB_MAXFRAGS) break; total_len += m->m_len; f = &c->wb_ptr->wb_frag[frag]; f->wb_ctl = WB_TXCTL_TLINK | m->m_len; if (frag == 0) { f->wb_ctl |= WB_TXCTL_FIRSTFRAG; f->wb_status = 0; } else f->wb_status = WB_TXSTAT_OWN; f->wb_next = vtophys(&c->wb_ptr->wb_frag[frag + 1]); f->wb_data = vtophys(mtod(m, vm_offset_t)); frag++; } } /* * Handle special case: we used up all 16 fragments, * but we have more mbufs left in the chain. Copy the * data into an mbuf cluster. Note that we don't * bother clearing the values in the other fragment * pointers/counters; it wouldn't gain us anything, * and would waste cycles. */ if (m != NULL) { struct mbuf *m_new = NULL; MGETHDR(m_new, M_DONTWAIT, MT_DATA); if (m_new == NULL) return(1); if (m_head->m_pkthdr.len > MHLEN) { MCLGET(m_new, M_DONTWAIT); if (!(m_new->m_flags & M_EXT)) { m_freem(m_new); return(1); } } m_copydata(m_head, 0, m_head->m_pkthdr.len, mtod(m_new, caddr_t)); m_new->m_pkthdr.len = m_new->m_len = m_head->m_pkthdr.len; m_freem(m_head); m_head = m_new; f = &c->wb_ptr->wb_frag[0]; f->wb_status = 0; f->wb_data = vtophys(mtod(m_new, caddr_t)); f->wb_ctl = total_len = m_new->m_len; f->wb_ctl |= WB_TXCTL_TLINK|WB_TXCTL_FIRSTFRAG; frag = 1; } if (total_len < WB_MIN_FRAMELEN) { f = &c->wb_ptr->wb_frag[frag]; f->wb_ctl = WB_MIN_FRAMELEN - total_len; f->wb_data = vtophys(&sc->wb_cdata.wb_pad); f->wb_ctl |= WB_TXCTL_TLINK; f->wb_status = WB_TXSTAT_OWN; frag++; } c->wb_mbuf = m_head; c->wb_lastdesc = frag - 1; WB_TXCTL(c) |= WB_TXCTL_LASTFRAG; WB_TXNEXT(c) = vtophys(&c->wb_nextdesc->wb_ptr->wb_frag[0]); return(0); } /* * Main transmit routine. To avoid having to do mbuf copies, we put pointers * to the mbuf data regions directly in the transmit lists. We also save a * copy of the pointers since the transmit list fragment pointers are * physical addresses. */ void wb_start(ifp) struct ifnet *ifp; { struct wb_softc *sc; struct mbuf *m_head = NULL; struct wb_chain *cur_tx = NULL, *start_tx; sc = ifp->if_softc; if (sc->wb_autoneg) { sc->wb_tx_pend = 1; return; } /* * Check for an available queue slot. If there are none, * punt. */ if (sc->wb_cdata.wb_tx_free->wb_mbuf != NULL) { ifp->if_flags |= IFF_OACTIVE; return; } start_tx = sc->wb_cdata.wb_tx_free; while(sc->wb_cdata.wb_tx_free->wb_mbuf == NULL) { IF_DEQUEUE(&ifp->if_snd, m_head); if (m_head == NULL) break; /* Pick a descriptor off the free list. */ cur_tx = sc->wb_cdata.wb_tx_free; sc->wb_cdata.wb_tx_free = cur_tx->wb_nextdesc; /* Pack the data into the descriptor. */ wb_encap(sc, cur_tx, m_head); if (cur_tx != start_tx) WB_TXOWN(cur_tx) = WB_TXSTAT_OWN; #if NBPFILTER > 0 /* * If there's a BPF listener, bounce a copy of this frame * to him. */ if (ifp->if_bpf) bpf_mtap(ifp->if_bpf, cur_tx->wb_mbuf); #endif } /* * If there are no packets queued, bail. */ if (cur_tx == NULL) return; /* * Place the request for the upload interrupt * in the last descriptor in the chain. This way, if * we're chaining several packets at once, we'll only * get an interupt once for the whole chain rather than * once for each packet. */ WB_TXCTL(cur_tx) |= WB_TXCTL_FINT; cur_tx->wb_ptr->wb_frag[0].wb_ctl |= WB_TXCTL_FINT; sc->wb_cdata.wb_tx_tail = cur_tx; if (sc->wb_cdata.wb_tx_head == NULL) { sc->wb_cdata.wb_tx_head = start_tx; WB_TXOWN(start_tx) = WB_TXSTAT_OWN; CSR_WRITE_4(sc, WB_TXSTART, 0xFFFFFFFF); } else { /* * We need to distinguish between the case where * the own bit is clear because the chip cleared it * and where the own bit is clear because we haven't * set it yet. The magic value WB_UNSET is just some * ramdomly chosen number which doesn't have the own * bit set. When we actually transmit the frame, the * status word will have _only_ the own bit set, so * the txeoc handler will be able to tell if it needs * to initiate another transmission to flush out pending * frames. */ WB_TXOWN(start_tx) = WB_UNSENT; } /* * Set a timeout in case the chip goes out to lunch. */ ifp->if_timer = 5; return; } void wb_init(xsc) void *xsc; { struct wb_softc *sc = xsc; struct ifnet *ifp = &sc->arpcom.ac_if; int s, i; u_int16_t phy_bmcr = 0; if (sc->wb_autoneg) return; s = splimp(); if (sc->wb_pinfo != NULL) phy_bmcr = wb_phy_readreg(sc, PHY_BMCR); /* * Cancel pending I/O and free all RX/TX buffers. */ wb_stop(sc); wb_reset(sc); sc->wb_txthresh = WB_TXTHRESH_INIT; /* * Set cache alignment and burst length. */ CSR_WRITE_4(sc, WB_BUSCTL, WB_BUSCTL_CONFIG); WB_CLRBIT(sc, WB_NETCFG, WB_NETCFG_TX_THRESH); WB_SETBIT(sc, WB_NETCFG, WB_TXTHRESH(sc->wb_txthresh)); /* This doesn't tend to work too well at 100Mbps. */ WB_CLRBIT(sc, WB_NETCFG, WB_NETCFG_TX_EARLY_ON); wb_setcfg(sc, phy_bmcr); /* Init our MAC address */ for (i = 0; i < ETHER_ADDR_LEN; i++) { CSR_WRITE_1(sc, WB_NODE0 + i, sc->arpcom.ac_enaddr[i]); } /* Init circular RX list. */ if (wb_list_rx_init(sc) == ENOBUFS) { printf("%s: initialization failed: no " "memory for rx buffers\n", sc->sc_dev.dv_xname); wb_stop(sc); (void)splx(s); return; } /* Init TX descriptors. */ wb_list_tx_init(sc); /* If we want promiscuous mode, set the allframes bit. */ if (ifp->if_flags & IFF_PROMISC) { WB_SETBIT(sc, WB_NETCFG, WB_NETCFG_RX_ALLPHYS); } else { WB_CLRBIT(sc, WB_NETCFG, WB_NETCFG_RX_ALLPHYS); } /* * Set capture broadcast bit to capture broadcast frames. */ if (ifp->if_flags & IFF_BROADCAST) { WB_SETBIT(sc, WB_NETCFG, WB_NETCFG_RX_BROAD); } else { WB_CLRBIT(sc, WB_NETCFG, WB_NETCFG_RX_BROAD); } /* * Program the multicast filter, if necessary. */ wb_setmulti(sc); /* * Load the address of the RX list. */ WB_CLRBIT(sc, WB_NETCFG, WB_NETCFG_RX_ON); CSR_WRITE_4(sc, WB_RXADDR, vtophys(&sc->wb_ldata->wb_rx_list[0])); /* * Enable interrupts. */ CSR_WRITE_4(sc, WB_IMR, WB_INTRS); CSR_WRITE_4(sc, WB_ISR, 0xFFFFFFFF); /* Enable receiver and transmitter. */ WB_SETBIT(sc, WB_NETCFG, WB_NETCFG_RX_ON); CSR_WRITE_4(sc, WB_RXSTART, 0xFFFFFFFF); WB_CLRBIT(sc, WB_NETCFG, WB_NETCFG_TX_ON); CSR_WRITE_4(sc, WB_TXADDR, vtophys(&sc->wb_ldata->wb_tx_list[0])); WB_SETBIT(sc, WB_NETCFG, WB_NETCFG_TX_ON); /* Restore state of BMCR */ if (sc->wb_pinfo != NULL) wb_phy_writereg(sc, PHY_BMCR, phy_bmcr); ifp->if_flags |= IFF_RUNNING; ifp->if_flags &= ~IFF_OACTIVE; (void)splx(s); return; } /* * Set media options. */ int wb_ifmedia_upd(ifp) struct ifnet *ifp; { struct wb_softc *sc; struct ifmedia *ifm; sc = ifp->if_softc; ifm = &sc->ifmedia; if (IFM_TYPE(ifm->ifm_media) != IFM_ETHER) return(EINVAL); if (IFM_SUBTYPE(ifm->ifm_media) == IFM_AUTO) wb_autoneg_mii(sc, WB_FLAG_SCHEDDELAY, 1); else wb_setmode_mii(sc, ifm->ifm_media); return(0); } /* * Report current media status. */ void wb_ifmedia_sts(ifp, ifmr) struct ifnet *ifp; struct ifmediareq *ifmr; { struct wb_softc *sc; u_int16_t advert = 0, ability = 0; sc = ifp->if_softc; ifmr->ifm_active = IFM_ETHER; if (!(wb_phy_readreg(sc, PHY_BMCR) & PHY_BMCR_AUTONEGENBL)) { if (wb_phy_readreg(sc, PHY_BMCR) & PHY_BMCR_SPEEDSEL) ifmr->ifm_active = IFM_ETHER|IFM_100_TX; else ifmr->ifm_active = IFM_ETHER|IFM_10_T; if (wb_phy_readreg(sc, PHY_BMCR) & PHY_BMCR_DUPLEX) ifmr->ifm_active |= IFM_FDX; else ifmr->ifm_active |= IFM_HDX; return; } ability = wb_phy_readreg(sc, PHY_LPAR); advert = wb_phy_readreg(sc, PHY_ANAR); if (advert & PHY_ANAR_100BT4 && ability & PHY_ANAR_100BT4) { ifmr->ifm_active = IFM_ETHER|IFM_100_T4; } else if (advert & PHY_ANAR_100BTXFULL && ability & PHY_ANAR_100BTXFULL) { ifmr->ifm_active = IFM_ETHER|IFM_100_TX|IFM_FDX; } else if (advert & PHY_ANAR_100BTXHALF && ability & PHY_ANAR_100BTXHALF) { ifmr->ifm_active = IFM_ETHER|IFM_100_TX|IFM_HDX; } else if (advert & PHY_ANAR_10BTFULL && ability & PHY_ANAR_10BTFULL) { ifmr->ifm_active = IFM_ETHER|IFM_10_T|IFM_FDX; } else if (advert & PHY_ANAR_10BTHALF && ability & PHY_ANAR_10BTHALF) { ifmr->ifm_active = IFM_ETHER|IFM_10_T|IFM_HDX; } return; } int wb_ioctl(ifp, command, data) struct ifnet *ifp; u_long command; caddr_t data; { struct wb_softc *sc = ifp->if_softc; struct ifreq *ifr = (struct ifreq *) data; struct ifaddr *ifa = (struct ifaddr *)data; int s, error = 0; s = splimp(); if ((error = ether_ioctl(ifp, &sc->arpcom, command, data)) > 0) { splx(s); return (error); } switch(command) { case SIOCSIFADDR: ifp->if_flags |= IFF_UP; switch (ifa->ifa_addr->sa_family) { #ifdef INET case AF_INET: wb_init(sc); arp_ifinit(&sc->arpcom, ifa); break; #endif /* INET */ default: wb_init(sc); } case SIOCSIFFLAGS: if (ifp->if_flags & IFF_UP) { wb_init(sc); } else { if (ifp->if_flags & IFF_RUNNING) wb_stop(sc); } error = 0; break; case SIOCADDMULTI: case SIOCDELMULTI: wb_setmulti(sc); error = 0; break; case SIOCGIFMEDIA: case SIOCSIFMEDIA: error = ifmedia_ioctl(ifp, ifr, &sc->ifmedia, command); break; default: error = EINVAL; break; } (void)splx(s); return(error); } void wb_watchdog(ifp) struct ifnet *ifp; { struct wb_softc *sc; sc = ifp->if_softc; if (sc->wb_autoneg) { wb_autoneg_mii(sc, WB_FLAG_DELAYTIMEO, 1); return; } ifp->if_oerrors++; printf("%s: watchdog timeout\n", sc->sc_dev.dv_xname); if (!(wb_phy_readreg(sc, PHY_BMSR) & PHY_BMSR_LINKSTAT)) printf("%s: no carrier - transceiver cable problem?\n", sc->sc_dev.dv_xname); wb_stop(sc); wb_reset(sc); wb_init(sc); if (ifp->if_snd.ifq_head != NULL) wb_start(ifp); return; } /* * Stop the adapter and free any mbufs allocated to the * RX and TX lists. */ void wb_stop(sc) struct wb_softc *sc; { register int i; struct ifnet *ifp; ifp = &sc->arpcom.ac_if; ifp->if_timer = 0; WB_CLRBIT(sc, WB_NETCFG, (WB_NETCFG_RX_ON|WB_NETCFG_TX_ON)); CSR_WRITE_4(sc, WB_IMR, 0x00000000); CSR_WRITE_4(sc, WB_TXADDR, 0x00000000); CSR_WRITE_4(sc, WB_RXADDR, 0x00000000); /* * Free data in the RX lists. */ for (i = 0; i < WB_RX_LIST_CNT; i++) { if (sc->wb_cdata.wb_rx_chain[i].wb_mbuf != NULL) { m_freem(sc->wb_cdata.wb_rx_chain[i].wb_mbuf); sc->wb_cdata.wb_rx_chain[i].wb_mbuf = NULL; } } bzero((char *)&sc->wb_ldata->wb_rx_list, sizeof(sc->wb_ldata->wb_rx_list)); /* * Free the TX list buffers. */ for (i = 0; i < WB_TX_LIST_CNT; i++) { if (sc->wb_cdata.wb_tx_chain[i].wb_mbuf != NULL) { m_freem(sc->wb_cdata.wb_tx_chain[i].wb_mbuf); sc->wb_cdata.wb_tx_chain[i].wb_mbuf = NULL; } } bzero((char *)&sc->wb_ldata->wb_tx_list, sizeof(sc->wb_ldata->wb_tx_list)); ifp->if_flags &= ~(IFF_RUNNING | IFF_OACTIVE); return; } /* * Stop all chip I/O so that the kernel's probe routines don't * get confused by errant DMAs when rebooting. */ void wb_shutdown(arg) void *arg; { struct wb_softc *sc = (struct wb_softc *)arg; wb_stop(sc); return; } struct cfattach wb_ca = { sizeof(struct wb_softc), wb_probe, wb_attach }; struct cfdriver wb_cd = { 0, "wb", DV_IFNET };