/* $OpenBSD: pccbbreg.h,v 1.11 2010/01/13 09:10:33 jsg Exp $ */ /* $NetBSD: pccbbreg.h,v 1.5 2000/06/07 09:02:47 haya Exp $ */ /* * Copyright (c) 1999 HAYAKAWA Koichi. All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. */ #ifndef _DEV_PCI_PCCBBREG_H_ #define _DEV_PCI_PCCBBREG_H_ #define PCI_SOCKBASE 0x10 /* Socket Base Address Register */ #define PCI_BUSNUM 0x18 /* Latency timer, Subordinate bus number */ #define PCI_BCR_INTR 0x3C /* Intr line, intr pin, bridge control regs */ #define PCI_LEGACY 0x44 /* Legacy IO register address (32 bits) */ #define PCI_SYSCTRL 0x80 /* System control */ #define PCI_CBCTRL 0x90 /* Retry status, Card ctrl, Device ctrl */ #define PCI_CLASS_INTERFACE_MASK 0xFFFFFF00 #define PCI_CLASS_INTERFACE_YENTA 0x06070000 /* CardBus latency timer, Subordinate bus no, CardBus bus no and PCI bus no */ #define PCI_CB_LSCP_REG 0x18 /* CardBus memory and io windows */ #define PCI_CB_MEMBASE0 0x1C #define PCI_CB_MEMLIMIT0 0x20 #define PCI_CB_MEMBASE1 0x24 #define PCI_CB_MEMLIMIT1 0x28 #define PCI_CB_IOBASE0 0x2C #define PCI_CB_IOLIMIT0 0x30 #define PCI_CB_IOBASE1 0x34 #define PCI_CB_IOLIMIT1 0x38 /* PCI_CB_LSCP_REG */ #define PCI_CB_LATENCY_SHIFT 24 #define PCI_CB_LATENCY_MASK 0xFF #define PCI_CB_LATENCY(x)( \ ((x) >> PCI_CB_LATENCY_SHIFT) & PCI_CB_LATENCY_MASK) /* * Cardbus socket registers */ #define CB_SOCKET_EVENT 0x00 /* Event */ #define CB_SOCKET_EVENT_CSTS 0x01 /* CARDSTS event occurs */ #define CB_SOCKET_EVENT_CD 0x06 /* CD event occurs */ #define CB_SOCKET_EVENT_CD1 0x02 /* CD1 event occurs */ #define CB_SOCKET_EVENT_CD2 0x04 /* CD2 event occurs */ #define CB_SOCKET_EVENT_POWER 0x08 /* Power cycle event occurs */ #define CB_SOCKET_MASK 0x04 /* Mask */ #define CB_SOCKET_MASK_CSTS 0x01 /* CARDSTS event mask */ #define CB_SOCKET_MASK_CD 0x06 /* CD event mask */ #define CB_SOCKET_MASK_POWER 0x08 /* Power cycle event mask */ #define CB_SOCKET_STAT 0x08 /* Present-state */ #define CB_SOCKET_STAT_CARDSTS 0x00000001 /* Card status change bit */ #define CB_SOCKET_STAT_CD1 0x00000002 /* Card detect 1 */ #define CB_SOCKET_STAT_CD2 0x00000004 /* Card detect 2 */ #define CB_SOCKET_STAT_CD 0x00000006 /* Card detect 1 and 2 */ #define CB_SOCKET_STAT_PWRCYCLE 0x00000008 /* Power cycle */ #define CB_SOCKET_STAT_16BIT 0x00000010 /* 16-bit card */ #define CB_SOCKET_STAT_CB 0x00000020 /* Cardbus card */ #define CB_SOCKET_STAT_IREQ 0x00000040 /* READY(~IREQ)//(~CINT) */ /* bit */ #define CB_SOCKET_STAT_NOTCARD 0x00000080 /* Inserted card is */ /* unrecognisable */ #define CB_SOCKET_STAT_DATALOST 0x00000100 /* Data lost */ #define CB_SOCKET_STAT_BADVCC 0x00000200 /* Bad Vcc Request */ #define CB_SOCKET_STAT_5VCARD 0x00000400 /* 5 V Card */ #define CB_SOCKET_STAT_3VCARD 0x00000800 /* 3.3 V Card */ #define CB_SOCKET_STAT_XVCARD 0x00001000 /* X.X V Card */ #define CB_SOCKET_STAT_YVCARD 0x00002000 /* Y.Y V Card */ #define CB_SOCKET_STAT_5VSOCK 0x10000000 /* 5 V Socket */ #define CB_SOCKET_STAT_3VSOCK 0x20000000 /* 3.3 V Socket */ #define CB_SOCKET_STAT_XVSOCK 0x40000000 /* X.X V Socket */ #define CB_SOCKET_STAT_YVSOCK 0x80000000 /* Y.Y V Socket */ #define CB_SOCKET_FORCE 0x0C /* Force event */ #define CB_SOCKET_FORCE_BADVCC 0x0200 /* Bad Vcc Request */ #define CB_SOCKET_CTRL 0x10 /* Control */ #define CB_SOCKET_CTRL_VPPMASK 0x007 #define CB_SOCKET_CTRL_VPP_OFF 0x000 #define CB_SOCKET_CTRL_VPP_12V 0x001 #define CB_SOCKET_CTRL_VPP_5V 0x002 #define CB_SOCKET_CTRL_VPP_3V 0x003 #define CB_SOCKET_CTRL_VPP_XV 0x004 #define CB_SOCKET_CTRL_VPP_YV 0x005 #define CB_SOCKET_CTRL_VCCMASK 0x070 #define CB_SOCKET_CTRL_VCC_OFF 0x000 #define CB_SOCKET_CTRL_VCC_5V 0x020 #define CB_SOCKET_CTRL_VCC_3V 0x030 #define CB_SOCKET_CTRL_VCC_XV 0x040 #define CB_SOCKET_CTRL_VCC_YV 0x050 #define CB_SOCKET_CTRL_STOPCLK 0x080 #define PCCBB_SOCKEVENT_BITS "\020\001CSTS\002CD1\003CD2\004PWR" #define PCCBB_SOCKSTATE_BITS \ "\020\001CSTS\002CD1\003CD3\004PWR\00516BIT\006CB\007CINT\010NOTA" \ "\011DLOST\012BADVCC\0135v\0143v\015Xv\016Yv\0355vS\0363vS\037XvS\040YvS" /* PCI_BCR_INTR bits for generic PCI-CardBus bridge */ #define CB_BCR_RESET_ENABLE 0x00400000 #define CB_BCR_INTR_IREQ_ENABLE 0x00800000 #define CB_BCR_PREFETCH_MEMWIN0 0x01000000 #define CB_BCR_PREFETCH_MEMWIN1 0x02000000 #define CB_BCR_WRITE_POST_ENABLE 0x04000000 /* TI [14][245]xx */ #define PCI12XX_MMCTRL 0x84 /* TI 12xx/14xx/15xx (except 1250, 1251, 1251B/1450) */ #define PCI12XX_MFUNC 0x8c #define PCI12XX_MFUNC_PIN0 0x0000000F #define PCI12XX_MFUNC_PIN0_INTA 0x02 #define PCI12XX_MFUNC_PIN1 0x000000F0 #define PCI12XX_MFUNC_PIN1_INTB 0x20 #define PCI12XX_MFUNC_PIN2 0x00000F00 #define PCI12XX_MFUNC_PIN3 0x0000F000 #define PCI12XX_MFUNC_PIN3_INTSER 0x00001000 #define PCI12XX_MFUNC_PIN4 0x000F0000 #define PCI12XX_MFUNC_PIN5 0x00F00000 #define PCI12XX_MFUNC_PIN6 0x0F000000 #define PCI12XX_MFUNC_DEFAULT PCI12XX_MFUNC_PIN3_INTSER /* PCI_CBCTRL bits for TI PCI113X */ #define PCI113X_CBCTRL_INT_SERIAL 0x040000 #define PCI113X_CBCTRL_INT_ISA 0x020000 #define PCI113X_CBCTRL_INT_MASK 0x060000 #define PCI113X_CBCTRL_RIENB 0x008000 /* Ring indicate output */ /* enable */ #define PCI113X_CBCTRL_ZVENAB 0x004000 /* ZV mode enable */ #define PCI113X_CBCTRL_PCI_IRQ_ENA 0x002000 /* PCI intr enable */ /* (funct and CSC) */ #define PCI113X_CBCTRL_PCI_INTR 0x001000 /* PCI functional intr req */ #define PCI113X_CBCTRL_PCI_CSC 0x000800 /* CSC intr route to PCI */ #define PCI113X_CBCTRL_PCI_CSC_D 0x000400 /* Unknown */ #define PCI113X_CBCTRL_SPK_ENA 0x000200 /* Speaker enable */ #define PCI113X_CBCTRL_INTR_DET 0x000100 /* Functional interrupt */ /* detect */ /* PCI_CBCTRL bits for TI PCI12XX */ #define PCI12XX_SYSCTRL_INTRTIE 0x20000000u #define PCI12XX_SYSCTRL_VCCPROT 0x200000 #define PCI12XX_SYSCTRL_PWRSAVE 0x000040 #define PCI12XX_SYSCTRL_SUBSYSRW 0x000020 #define PCI12XX_SYSCTRL_CB_DPAR 0x000010 #define PCI12XX_SYSCTRL_CDMA_EN 0x000008 #define PCI12XX_SYSCTRL_KEEPCLK 0x000002 #define PCI12XX_SYSCTRL_RIMUX 0x000001 #define PCI12XX_CBCTRL_CSC 0x20000000u #define PCI12XX_CBCTRL_ASYNC_CSC 0x01000000u #define PCI12XX_CBCTRL_INT_SERIAL 0x060000 #define PCI12XX_CBCTRL_INT_PCI_SERIAL 0x040000 #define PCI12XX_CBCTRL_INT_ISA 0x020000 #define PCI12XX_CBCTRL_INT_PCI 0x000000 #define PCI12XX_CBCTRL_INT_MASK 0x060000 #define PCI12XX_CBCTRL_RIENB 0x008000 /* Ring indicate output */ /* enable */ #define PCI12XX_CBCTRL_ZVENAB 0x004000 /* ZV mode enable */ #define PCI12XX_CBCTRL_AUD2MUX 0x000400 /* Unknown */ #define PCI12XX_CBCTRL_SPK_ENA 0x000200 /* Speaker enable */ #define PCI12XX_CBCTRL_INTR_DET 0x000100 /* Functional interrupt */ /* detect */ /* PCI_BCR_INTR additional bit for Rx5C46[567] */ #define CB_BCRI_RL_3E0_ENA 0x08000000 #define CB_BCRI_RL_3E2_ENA 0x10000000 /* * Special register definition for Toshiba ToPIC95/97 * These values are borrowed from pcmcia-cs/Linux. */ #define TOPIC_SOCKET_CTRL 0x90 #define TOPIC_SOCKET_CTRL_SCR_IRQSEL 0x00000001 /* PCI intr */ #define TOPIC_SLOT_CTRL 0xA0 #define TOPIC_SLOT_CTRL_SLOTON 0x00000080 #define TOPIC_SLOT_CTRL_SLOTEN 0x00000040 #define TOPIC_SLOT_CTRL_ID_LOCK 0x00000020 #define TOPIC_SLOT_CTRL_ID_WP 0x00000010 #define TOPIC_SLOT_CTRL_PORT_MASK 0x0000000C #define TOPIC_SLOT_CTRL_PORT_SHIFT 2 #define TOPIC_SLOT_CTRL_OSF_MASK 0x00000003 #define TOPIC_SLOT_CTRL_OSF_SHIFT 0 #define TOPIC_SLOT_CTRL_INTB 0x00002000 #define TOPIC_SLOT_CTRL_INTA 0x00001000 #define TOPIC_SLOT_CTRL_INT_MASK 0x00003000 #define TOPIC_SLOT_CTRL_CLOCK_MASK 0x00000C00 #define TOPIC_SLOT_CTRL_CLOCK_2 0x00000800 /* PCI Clock/2 */ #define TOPIC_SLOT_CTRL_CLOCK_1 0x00000400 /* PCI Clock */ #define TOPIC_SLOT_CTRL_CLOCK_0 0x00000000 /* No clock */ #define TOPIC97_SLOT_CTRL_STSIRQP 0x00000400 /* Status change intr */ /* pulse */ #define TOPIC97_SLOT_CTRL_IRQP 0x00000200 /* Function intr pulse */ #define TOPIC97_SLOT_CTRL_PCIINT 0x00000100 /* Intr routing to PCI INT */ #define TOPIC_SLOT_CTRL_CARDBUS 0x80000000 #define TOPIC_SLOT_CTRL_VS1 0x04000000 #define TOPIC_SLOT_CTRL_VS2 0x02000000 #define TOPIC_SLOT_CTRL_SWDETECT 0x01000000 #define TOPIC_REG_CTRL 0x00A4 #define TOPIC_REG_CTRL_RESUME_RESET 0x80000000 #define TOPIC_REG_CTRL_REMOVE_RESET 0x40000000 #define TOPIC97_REG_CTRL_CLKRUN_ENA 0x20000000 #define TOPIC97_REG_CTRL_TESTMODE 0x10000000 #define TOPIC97_REG_CTRL_IOPLUP 0x08000000 #define TOPIC_REG_CTRL_BUFOFF_PWROFF 0x02000000 #define TOPIC_REG_CTRL_BUFOFF_SIGOFF 0x01000000 #define TOPIC97_REG_CTRL_CB_DEV_MASK 0x0000F800 #define TOPIC97_REG_CTRL_CB_DEV_SHIFT 11 #define TOPIC97_REG_CTRL_RI_DISABLE 0x00000004 #define TOPIC97_REG_CTRL_CAUDIO_OFF 0x00000002 #define TOPIC_REG_CTRL_CAUDIO_INVERT 0x00000001 /* * Additional (subset of) Topic100 registers from * Toshiba datasheet (Draft Rev. 01.4) 98/10/07 */ #define TOPIC100_PMCSR 0x84 /* Power mgmt ctrl/stat register */ #define TOPIC100_PMCSR_MASK 0x00000003 #define TOPIC100_PMCSR_D0 0x0 /* * Additional O2Micro registers * * 'reserved' register at 0x94/D4. allows setting read prefetch and write * bursting. read prefetching for example makes the RME Hammerfall DSP * working. for some bridges it is at 0x94, for others at 0xD4. it's * ok to write to both registers on all O2 bridges. * from Eric Still, 02Micro. */ #define O2MICRO_RESERVED1 0x94 #define O2MICRO_RESERVED2 0xD4 #define O2MICRO_RES_READ_PREFETCH 0x02 #define O2MICRO_RES_WRITE_BURST 0x08 #endif /* _DEV_PCI_PCCBBREG_H_ */