.\"	$OpenBSD: apmd.8,v 1.50 2018/12/04 18:00:57 tedu Exp $
.\"
.\" Copyright (c) 1995 John T. Kohl
.\" All rights reserved.
.\"
.\" Redistribution and use in source and binary forms, with or without
.\" modification, are permitted provided that the following conditions
.\" are met:
.\" 1. Redistributions of source code must retain the above copyright
.\"    notice, this list of conditions and the following disclaimer.
.\" 2. Redistributions in binary form must reproduce the above copyright
.\"    notice, this list of conditions and the following disclaimer in the
.\"    documentation and/or other materials provided with the distribution.
.\" 3. The name of the author may not be used to endorse or promote products
.\"    derived from this software without specific prior written permission.
.\"
.\" THIS SOFTWARE IS PROVIDED BY THE AUTHOR `AS IS'' AND ANY EXPRESS OR
.\" IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
.\" WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
.\" DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT,
.\" INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
.\" (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
.\" SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
.\" HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
.\" STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
.\" ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
.\" POSSIBILITY OF SUCH DAMAGE.
.\"
.Dd $Mdocdate: December 4 2018 $
.Dt APMD 8
.Os
.Sh NAME
.Nm apmd
.Nd Advanced Power Management daemon
.Sh SYNOPSIS
.Nm apmd
.Op Fl AadHLs
.Op Fl f Ar devname
.Op Fl S Ar sockname
.Op Fl t Ar seconds
.Op Fl Z Ar percent
.Op Fl z Ar percent
.Sh DESCRIPTION
.Nm
monitors the advanced power management device,
.Xr apm 4 ,
acting on signaled events and upon user requests as sent by the
.Xr apm 8
program.
.Pp
For suspend and standby request events delivered by the BIOS, or via
.Xr apm 8 ,
.Nm
runs the appropriate configuration program (if one exists),
syncs the buffer cache to disk and initiates the requested state.
When resuming after suspend or standby,
.Nm
runs the appropriate configuration program (if one exists).
.Pp
When the power status changes
(battery is connected or disconnected)
.Nm
fetches the current status and reports it via
.Xr syslog 3
with logging facility
.Dv LOG_DAEMON .
.Pp
The options are as follows:
.Bl -tag -width Ds
.It Fl A
Start
.Nm
in automatic performance adjustment mode.
.It Fl a
BIOS-initiated suspend or standby requests are
ignored if the system is connected to line current and not running from
batteries (user requests are still honored).
.It Fl d
.Nm
enters debug mode, staying in the foreground.
Logging output is printed to stdout.
.It Fl f Ar devname
Specify an alternate device file name,
.Ar devname .
.It Fl H
Start
.Nm
in manual performance adjustment mode, initialising
.Va hw.setperf
to 100.
.It Fl L
Start
.Nm
in manual performance adjustment mode, initialising
.Va hw.setperf
to 0.
.It Fl S Ar sockname
Specify an alternate socket name,
.Ar sockname .
The socket is protected to mode 0660, UID 0, GID 0; this protects access
to suspend requests to authorized users only.
.It Fl s
Current battery statistics are reported via
.Xr syslog 3
and
.Nm
exits without monitoring the APM status.
.It Fl t Ar seconds
.Nm
periodically polls the APM driver for the current power state.
If the battery charge level changes substantially or the external power
status changes, the new status is logged.
The polling rate defaults to
once per 10 minutes, but may be specified using the
.Fl t
command-line flag.
.It Fl Z Ar percent
Automatically hibernate the system if no AC is connected and the
estimated battery life is equal or below
.Ar percent .
.It Fl z Ar percent
Automatically suspend the system if no AC is connected and the
estimated battery life is equal or below
.Ar percent .
.Pp
If both
.Fl Z
and
.Fl z
are specified, the last one will supersede the other.
.El
.Pp
When a client requests a suspend or stand-by state,
.Nm
does not wait for positive confirmation that the requested
state has been entered before replying to the client; to do so would mean
the client does not get a reply until the system resumes from its sleep state.
Rather,
.Nm
replies with the intended state to the client and then places the system
in the requested state after running the configuration script and
flushing the buffer cache.
.Pp
Actions can be configured for the following transitions:
suspend,
hibernate,
standby,
resume,
powerup,
and
powerdown.
The suspend, hibernate and standby actions are run prior to
.Nm
performing any other actions (such as disk syncs) and entering the new
state.
The resume program is run after resuming from a stand-by or
suspended state.
The powerup and powerdown programs are run after the power status (AC
connected or not) changes, as well as after a resume (if the power
status changed in the mean time).
.Sh FILES
.Bl -tag -width "/etc/apm/powerdownXX" -compact
.It Pa /dev/apmctl
Default device used to control the APM kernel driver.
.Pp
.It Pa /etc/apm/suspend
.It Pa /etc/apm/hibernate
.It Pa /etc/apm/standby
.It Pa /etc/apm/resume
.It Pa /etc/apm/powerup
.It Pa /etc/apm/powerdown
These files contain the host's customized actions.
Each file must be an executable binary or shell script.
A single program or script can be used to control all transitions
by examining the name by which it was called,
which is one of
suspend,
hibernate,
standby,
resume,
powerup,
or
powerdown.
.Pp
.It Pa /var/run/apmdev
Default
.Ux Ns -domain
socket used for communication with
.Xr apm 8 .
.El
.Sh SEE ALSO
.Xr syslog 3 ,
.Xr apm 4 ,
.Xr apm 8 ,
.Xr sysctl 8
.Pp
Advanced Power Management (APM) BIOS Interface Specification
(revision 1.2),
Intel Corporation and Microsoft Corporation.
.Sh HISTORY
The
.Nm
command first appeared in
.Nx 1.3 .
.Ox
support was added in
.Ox 1.2 .