.\" $OpenBSD: ntpd.conf.5,v 1.37 2017/08/10 22:59:42 job Exp $ .\" .\" Copyright (c) 2003, 2004 Henning Brauer .\" .\" Permission to use, copy, modify, and distribute this software for any .\" purpose with or without fee is hereby granted, provided that the above .\" copyright notice and this permission notice appear in all copies. .\" .\" THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES .\" WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF .\" MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR .\" ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES .\" WHATSOEVER RESULTING FROM LOSS OF MIND, USE, DATA OR PROFITS, WHETHER IN .\" AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT .\" OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. .\" .Dd $Mdocdate: August 10 2017 $ .Dt NTPD.CONF 5 .Os .Sh NAME .Nm ntpd.conf .Nd Network Time Protocol daemon configuration file .Sh DESCRIPTION This manual page describes the format of the .Xr ntpd 8 configuration file. .Pp .Nm has the following format: .Pp Empty lines and lines beginning with the .Sq # character are ignored. .Pp Keywords may be specified multiple times within the configuration file. The basic configuration options are as follows: .Bl -tag -width Ds .It Xo Ic listen on Ar address .Op Ic rtable Ar table-id .Xc Specify a local IP address or a hostname the .Xr ntpd 8 daemon should listen on. If it appears multiple times, .Xr ntpd 8 will listen on each given address. If .Sq * is given as an address, .Xr ntpd 8 will listen on all local addresses using the specified routing table. .Xr ntpd 8 does not listen on any address by default. The optional .Ic rtable keyword will specify which routing table to listen on. By default .Xr ntpd 8 will listen using the current routing table. For example: .Bd -literal -offset indent listen on * .Ed .Pp or .Bd -literal -offset indent listen on 127.0.0.1 listen on ::1 listen on 127.0.0.1 rtable 4 .Ed .It Ic query from Ar address Specify a local IP address the .Xr ntpd 8 daemon should use for outgoing queries to subsequently specified servers. For example: .Bd -literal -offset indent query from 192.0.2.1 query from 2001:db8::1 .Ed .It Xo Ic sensor Ar device .Op Ic correction Ar microseconds .Op Ic weight Ar weight-value .Op Ic refid Ar string .Op Ic stratum Ar stratum-value .Xc Specify a timedelta sensor device .Xr ntpd 8 should use. The sensor can be specified multiple times: .Xr ntpd 8 will use each given sensor that actually exists. Non-existent sensors are ignored. If .Sq * is given as device name, .Xr ntpd 8 will use all timedelta sensors it finds. .Xr ntpd 8 does not use any timedelta sensor by default. For example: .Bd -literal -offset indent sensor * sensor nmea0 .Ed .Pp An optional correction in microseconds can be given to compensate for the sensor's offset. The maximum correction is 127 seconds. For example, if a DCF77 receiver is lagging 70ms behind actual time: .Bd -literal -offset indent sensor udcf0 correction 70000 .Ed .Pp The optional .Ic weight keyword permits finer control over the relative importance of time sources (servers or sensor devices). Weights are specified in the range 1 to 10; if no weight is given, the default is 1. A server with a weight of 5, for example, will have five times more influence on time offset calculation than a server with a weight of 1. .Pp An optional reference ID string - up to 4 ASCII characters - can be given to publish the sensor type to clients. RFC 2030 suggests some common reference identifiers, but new identifiers "can be contrived as appropriate." If an ID string is not given, .Xr ntpd 8 will use a generic reference ID. For example: .Bd -literal -offset indent sensor nmea0 refid GPS .Ed .Pp A stratum value other than the default of 1 can be assigned using the .Ic stratum keyword. .It Xo Ic server Ar address .Op Ic weight Ar weight-value .Xc Specify the IP address or the hostname of an NTP server to synchronize to. If it appears multiple times, .Xr ntpd 8 will try to synchronize to all of the servers specified. If a hostname resolves to multiple IPv4 and/or IPv6 addresses, .Xr ntpd 8 uses the first address. If it does not get a reply, .Xr ntpd 8 retries with the next address and continues to do so until a working address is found. For example: .Bd -literal -offset indent server 10.0.0.2 weight 5 server ntp.example.org weight 1 .Ed .Pp To provide redundancy, it is good practice to configure multiple servers. In general, best accuracy is obtained by using servers that have a low network latency. .It Xo Ic servers Ar address .Op Ic weight Ar weight-value .Xc As with .Cm server , specify the IP address or hostname of an NTP server to synchronize to. If it appears multiple times, .Xr ntpd 8 will try to synchronize to all of the servers specified. Should the hostname resolve to multiple IP addresses, .Xr ntpd 8 will try to synchronize to all of them. For example: .Bd -literal -offset indent servers pool.ntp.org servers pool.ntp.org weight 5 .Ed .El .Sh CONSTRAINTS .Xr ntpd 8 can be configured to query the .Sq Date from trusted HTTPS servers via TLS. This time information is not used for precision but acts as an authenticated constraint, thereby reducing the impact of unauthenticated NTP man-in-the-middle attacks. Received NTP packets with time information falling outside of a range near the constraint will be discarded and such NTP servers will be marked as invalid. .Bl -tag -width Ds .It Ic constraint from Ar url Specify the URL, IP address or the hostname of an HTTPS server to provide a constraint. If .Ic constraint from is used more than once, .Xr ntpd 8 will calculate a median constraint from all the servers specified. .Bd -literal -offset indent server ntp.example.org constraint from www.example.com .Ed .It Ic constraints from Ar url As with .Ic constraint from , specify the URL, IP address or the hostname of an HTTPS server to provide a constraint. Should the hostname resolve to multiple IP addresses, .Xr ntpd 8 will calculate a median constraint from all of them. For example: .Bd -literal -offset indent servers pool.ntp.org constraints from "https://www.google.com/" .Ed .El .Sh FILES .Bl -tag -width "/etc/ntpd.confXXX" -compact .It Pa /etc/ntpd.conf default .Xr ntpd 8 configuration file .El .Sh SEE ALSO .Xr ntpctl 8 , .Xr ntpd 8 , .Xr sysctl 8 .Sh HISTORY The .Nm file format first appeared in .Ox 3.6 .