.\" $OpenBSD: traceroute.8,v 1.66 2016/10/21 09:26:36 jmc Exp $ .\" $NetBSD: traceroute.8,v 1.6 1995/10/12 03:05:50 mycroft Exp $ .\" .\" Copyright (c) 1990, 1991, 1993 .\" The Regents of the University of California. All rights reserved. .\" .\" This code is derived from software contributed to Berkeley by .\" Van Jacobson. .\" .\" Redistribution and use in source and binary forms, with or without .\" modification, are permitted provided that the following conditions .\" are met: .\" 1. Redistributions of source code must retain the above copyright .\" notice, this list of conditions and the following disclaimer. .\" 2. Redistributions in binary form must reproduce the above copyright .\" notice, this list of conditions and the following disclaimer in the .\" documentation and/or other materials provided with the distribution. .\" 3. Neither the name of the University nor the names of its contributors .\" may be used to endorse or promote products derived from this software .\" without specific prior written permission. .\" .\" THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND .\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE .\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE .\" ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE .\" FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL .\" DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS .\" OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) .\" HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT .\" LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY .\" OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF .\" SUCH DAMAGE. .\" .\" @(#)traceroute.8 8.1 (Berkeley) 6/6/93 .\" .Dd $Mdocdate: October 21 2016 $ .Dt TRACEROUTE 8 .Os .Sh NAME .Nm traceroute , .Nm traceroute6 .Nd print the route packets take to network host .Sh SYNOPSIS .Nm traceroute\ \& .Op Fl AcDdIlnSvx .Op Fl f Ar first_ttl .Op Fl g Ar gateway_addr .Op Fl m Ar max_ttl .Op Fl P Ar proto .Op Fl p Ar port .Op Fl q Ar nqueries .Op Fl s Ar src_addr .Op Fl t Ar toskeyword .Op Fl V Ar rtable .Op Fl w Ar waittime .Ar host .Op Ar datalen .Nm traceroute6 .Op Fl AcDdIlnSv .Op Fl f Ar first_hop .Op Fl m Ar max_hop .Op Fl p Ar port .Op Fl q Ar nqueries .Op Fl s Ar src_addr .Op Fl V Ar rtable .Op Fl w Ar waittime .Ar host .Op Ar datalen .Sh DESCRIPTION The Internet is a large and complex aggregation of network hardware, connected together by gateways. Tracking the route packets follow (or finding the miscreant gateway that's discarding packets) can be difficult. .Nm and .Nm traceroute6 attempt to elicit .Dv TIME_EXCEEDED responses from each gateway along the path to .Ar host , in order to determine their route. .Nm is used for IPv4 networks and .Nm traceroute6 for IPv6. .Pp The options are as follows: .Bl -tag -width Ds .It Fl A Look up the AS number for each hop address. Uses the DNS service described at .Lk http://www.team-cymru.org/Services/ip-to-asn.html . .It Fl c Do not increment the destination port number in successive UDP packets. Rather, all UDP packets will have the same destination port, as set via the .Fl p flag (or 33434 if none is specified). .It Fl D Dump the packet data to standard error before transmitting it. .It Fl d Turn on socket-level debugging. .It Fl f Ar first_ttl Set the first TTL or hop limit used in outgoing probe packets. The effect is that the first first_ttl \- 1 hosts will be skipped in the output of .Nm traceroute . The default is 1 (skip no hosts). .It Fl g Ar gateway_addr Add .Ar gateway_addr to the list of addresses in the IP Loose Source Record Route (LSRR) option. If no gateways are specified, the LSRR option is omitted. This option is not available for IPv6. .It Fl I Use ICMP or ICMP6 ECHO instead of UDP datagrams. .It Fl l Display the TTL or hop limit value of the returned packet. This is useful for checking for asymmetric routing. .It Fl m Ar max_ttl Set the maximum TTL or hop limit. The default is the value of the system's .Va net.inet.ip.ttl or .Va net.inet6.ip6.hlim .Xr sysctl 8 variable, which defaults to 64. .It Fl n Print hop addresses numerically rather than symbolically and numerically (saves a nameserver address-to-name lookup for each gateway found on the path). .It Fl P Ar proto Change the protocol being used from UDP to a numeric protocol or a name as specified in .Pa /etc/protocols . This will not work reliably for most protocols. If set to 1 (ICMP), then ICMP Echo Request messages will be used (same as .Xr ping 8 ) . This option is not available for IPv6. .It Fl p Ar port Set the base UDP .Ar port number used in probes. The default is 33434. .Nm hopes that nothing is listening on UDP ports .Ar base to .Ar base Ns + Ns Ar nhops Ns * Ns Ar nqueries Ns -1 at the destination host (so an ICMP .Dv PORT_UNREACHABLE message will be returned to terminate the route tracing). If something is listening on a port in the default range, this option can be used to pick an unused port range. .It Fl q Ar nqueries Set the number of probes per TTL to .Ar nqueries . The default is three probes. .It Fl S Print how many probes were not answered for each hop. .It Fl s Ar src_addr Use the following IP address (which must be given as an IP number, not a hostname) as the source address in outgoing probe packets. On hosts with more than one IP address, this option can be used to force the source address to be something other than the IP address of the interface the probe packet is sent on. If the IP address is not one of this machine's interface addresses and the user is not the superuser, an error is returned and nothing is sent. .It Fl t Ar toskeyword Set the type-of-service (TOS) in probe packets. The value may be one of .Cm critical , .Cm inetcontrol , .Cm lowdelay , .Cm netcontrol , .Cm throughput , .Cm reliability , or one of the DiffServ Code Points: .Cm ef , .Cm af11 ... af43 , .Cm cs0 ... cs7 ; or a number in either hex or decimal. The default is zero. This option can be used to see if different types-of-service result in different paths. If this option is used, changes to the type-of-service in the returned packets are displayed. Not all values of TOS are legal or meaningful \- see the IP spec for definitions. Useful values are probably .Cm lowdelay and .Cm throughput . This option is not available for IPv6. .It Fl V Ar rtable Set the routing table to be used. .It Fl v Verbose output. Received ICMP packets other than .Dv TIME_EXCEEDED and .Dv UNREACHABLE Ns s are listed. .It Fl w Ar waittime Set the time, in seconds, to wait for a response to a probe. The default is 5. .It Fl x Print the ICMP extended headers if available. This option is not available for IPv6. .It Ar host The destination host, specified as a host name or numeric IP address. .It Ar datalen The probe datagram length. The default is 40 bytes for IPv4 UDP and 60 bytes for ICMP, IPv6 UDP and ICMP6. .El .Pp The program attempts to trace the route an IP packet would follow to a host by launching UDP probe packets with a small TTL or hop limit, then listening for an ICMP "time exceeded" reply from a gateway. It starts using probes with a TTL/hop limit of one and increases by one until it gets an ICMP "port unreachable" (which means it reached the host) or hits a maximum limit (which defaults to 64, but can be changed using the .Fl m option). Three probes (the exact number can be changed using the .Fl q option) are sent and a line is printed showing the TTL or hop limit, address of the gateway, and round trip time of each probe. If the probe answers come from different gateways, the address of each responding system will be printed. If there is no response within a 5 second timeout interval (which can be changed using the .Fl w option), a "*" is printed for that probe. .Pp We don't want the destination host to process the UDP probe packets so the destination port is set to an unlikely value (if some clod on the destination is using that value, it can be changed using the .Fl p option). .Pp A sample use and output might be: .Bd -literal -offset indent $ traceroute nis.nsf.net. traceroute to nis.nsf.net (35.1.1.48), 64 hops max, 56 byte packet 1 helios.ee.lbl.gov (128.3.112.1) 19 ms 19 ms 0 ms 2 lilac-dmc.Berkeley.EDU (128.32.216.1) 39 ms 39 ms 19 ms 3 lilac-dmc.Berkeley.EDU (128.32.216.1) 39 ms 39 ms 19 ms 4 ccngw-ner-cc.Berkeley.EDU (128.32.136.23) 39 ms 40 ms 39 ms 5 ccn-nerif22.Berkeley.EDU (128.32.168.22) 39 ms 39 ms 39 ms 6 128.32.197.4 (128.32.197.4) 40 ms 59 ms 59 ms 7 131.119.2.5 (131.119.2.5) 59 ms 59 ms 59 ms 8 129.140.70.13 (129.140.70.13) 99 ms 99 ms 80 ms 9 129.140.71.6 (129.140.71.6) 139 ms 239 ms 319 ms 10 129.140.81.7 (129.140.81.7) 220 ms 199 ms 199 ms 11 nic.merit.edu (35.1.1.48) 239 ms 239 ms 239 ms .Ed .Pp Note that lines 2 & 3 are the same. This is due to a buggy kernel on the 2nd hop system \- lbl-csam.arpa \- that forwards packets with a zero TTL (a bug in the distributed version of .Bx 4.3 ) . Note that you have to guess what path the packets are taking cross-country since the NSFNET (129.140) doesn't supply address-to-name translations for its NSSes. .Pp A more interesting example is: .Bd -literal -offset indent $ traceroute allspice.lcs.mit.edu. traceroute to allspice.lcs.mit.edu (18.26.0.115), 64 hops max 1 helios.ee.lbl.gov (128.3.112.1) 0 ms 0 ms 0 ms 2 lilac-dmc.Berkeley.EDU (128.32.216.1) 19 ms 19 ms 19 ms 3 lilac-dmc.Berkeley.EDU (128.32.216.1) 39 ms 19 ms 19 ms 4 ccngw-ner-cc.Berkeley.EDU (128.32.136.23) 19 ms 39 ms 39 ms 5 ccn-nerif22.Berkeley.EDU (128.32.168.22) 20 ms 39 ms 39 ms 6 128.32.197.4 (128.32.197.4) 59 ms 119 ms 39 ms 7 131.119.2.5 (131.119.2.5) 59 ms 59 ms 39 ms 8 129.140.70.13 (129.140.70.13) 80 ms 79 ms 99 ms 9 129.140.71.6 (129.140.71.6) 139 ms 139 ms 159 ms 10 129.140.81.7 (129.140.81.7) 199 ms 180 ms 300 ms 11 129.140.72.17 (129.140.72.17) 300 ms 239 ms 239 ms 12 * * * 13 128.121.54.72 (128.121.54.72) 259 ms 499 ms 279 ms 14 * * * 15 * * * 16 * * * 17 * * * 18 ALLSPICE.LCS.MIT.EDU (18.26.0.115) 339 ms 279 ms 279 ms .Ed .Pp Note that the gateways 12, 14, 15, 16 & 17 hops away either don't send ICMP "time exceeded" messages or send them with a TTL too small to reach us. 14 \- 17 are running the MIT C Gateway code that doesn't send "time exceeded"s. God only knows what's going on with 12. .Pp The silent gateway 12 in the above may be the result of a bug in the 4.[23] .Bx network code (and its derivatives): 4.x (x <= 3) sends an unreachable message using whatever TTL remains in the original datagram. Since, for gateways, the remaining TTL is zero, the ICMP "time exceeded" is guaranteed to not make it back to us. The behavior of this bug is slightly more interesting when it appears on the destination system: .Bd -literal -offset indent 1 helios.ee.lbl.gov (128.3.112.1) 0 ms 0 ms 0 ms 2 lilac-dmc.Berkeley.EDU (128.32.216.1) 39 ms 19 ms 39 ms 3 lilac-dmc.Berkeley.EDU (128.32.216.1) 19 ms 39 ms 19 ms 4 ccngw-ner-cc.Berkeley.EDU (128.32.136.23) 39 ms 40 ms 19 ms 5 ccn-nerif35.Berkeley.EDU (128.32.168.35) 39 ms 39 ms 39 ms 6 csgw.Berkeley.EDU (128.32.133.254) 39 ms 59 ms 39 ms 7 * * * 8 * * * 9 * * * 10 * * * 11 * * * 12 * * * 13 rip.Berkeley.EDU (128.32.131.22) 59 ms ! 39 ms ! 39 ms ! .Ed .Pp Notice that there are 12 "gateways" (13 is the final destination) and exactly the last half of them are "missing". What's really happening is that rip (a Sun-3 running Sun OS3.5) is using the TTL from our arriving datagram as the TTL in its ICMP reply. So, the reply will time out on the return path (with no notice sent to anyone since ICMPs aren't sent for ICMPs) until we probe with a TTL that's at least twice the path length. That is, rip is really only 7 hops away. A reply that returns with a TTL of 1 is a clue this problem exists. .Nm prints a "!" after the time if the TTL is <= 1. Since vendors ship a lot of obsolete (DEC's Ultrix, Sun 3.x) or non-standard (HP-UX) software, expect to see this problem frequently and/or take care picking the target host of your probes. .Pp Other possible annotations after the time are .Sy !H , .Sy !N , .Sy !P (got a host, network or protocol unreachable, respectively), .Sy !A , .Sy !C (access to the network or host, respectively, is prohibited), .Sy !X (communication administratively prohibited by filtering), .Sy !S or .Sy !F (source route failed or fragmentation needed \- neither of these should ever occur and the associated gateway is busted if you see one), .Sy !U (destination network or host unknown), .Sy !T (destination network or host unreachable for TOS), .Sy ! (other ICMP unreachable code). .Sy TOS=xxx! (TOS bit in returned packet differs from last hop). If almost all the probes result in some kind of unreachable, .Nm will give up and exit. .Pp .Dl $ traceroute -g 10.3.0.5 128.182.0.0 .Pp will show the path from the Cambridge Mailbridge to PSC, while .Pp .Dl $ traceroute -g 192.5.146.4 -g 10.3.0.5 35.0.0.0 .Pp will show the path from the Cambridge Mailbridge to Merit, using PSC to reach the Mailbridge. .Pp This program is intended for use in network testing, measurement and management. It should be used primarily for manual fault isolation. Because of the load it could impose on the network, it is unwise to use .Nm during normal operations or from automated scripts. .Sh SEE ALSO .Xr netstat 1 , .Xr ping 8 .Sh HISTORY The very first .Nm (never released) used ICMP ECHO_REQUEST datagrams as probe packets. During the first night of testing it was discovered that more than half the router vendors of the time would not return an ICMP TIME_EXCEEDED for an ECHO_REQUEST. .Nm was then changed to use UDP probe packets. Most modern TCP/IP implementations will now generate an ICMP error message to ICMP query messages, and the option to use ECHO_REQUEST probes was re-implemented. .Pp The .Nm command first appeared in .Bx 4.4 . The .Nm traceroute6 command first appeared in the WIDE Hydrangea IPv6 protocol stack kit. .Sh AUTHORS .An -nosplit Implemented by .An Van Jacobson from a suggestion by .An Steve Deering . Debugged by a cast of thousands with particularly cogent suggestions or fixes from .An C. Philip Wood , .An Tim Seaver , and .An Ken Adelman .