1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
|
OpenBSDInstallPrelude
OpenBSDInstallPart2
If you have a small machine (less than 6MB of fast RAM) you'll
have to setup a miniroot filesystem in the swap partition, as
described in the "Preparing your System for OpenBSD Installation"
section above. If your machine has 6MB or more we strongly
recommend using the ramdisk kernel instead. This way you don't
need to setup any root image beforehand.
You need to have the "loadbsd" program in your command path.
If AmigaDOS complains about loadbsd not being an executable file,
be sure that the "Execute" protection bit is set. If not, set it
with the command:
Protect loadbsd add e
Next you need to get yourself into OpenBSD by loading the
kernel from AmigaDOS with loadbsd like so:
loadbsd bsd.rd
or, if you are doing a miniroot install:
loadbsd -b bsd
If you have an AGA machine, and your monitor will handle
the dblNTSC mode, you may also {:-include-:} the "-A" option to
enable the dblNTSC display mode.
OpenBSDBootMsgs
If you are doing the miniroot install you will be prompted for a
root device. At this time type 'sd0*', where '0' is the device
which holds the miniroot-containing swap partition you created
during the hard disk preparation. If the system should hang
after entering the root device, try again with
loadbsd -I ff -b bsd
This disables synchronous transfer on all SCSI devices. For
ramdisk installations this kind of hang might occur later during
the install when accessing the SCSI disk for the first time. If
such a hang occurs, try again with:
loadbsd -I ff bsd.rd
While booting, you will probably see several warnings. You
should be warned that no swap space is present. Do not be
alarmed, these are completely normal. When you reach the prompt
asking you for a shell name, just hit return.
You will be asked which terminal type to use, you should just
hit return to select the default (vt220).
The install program will then tell you which disks of that
type it can install on, and ask you which it should use. The
name of the disk is typically "sd0" for SCSI drives or the
A4000 IDE drives or "wd0" for ISA-connected IDE drives. Reply
with the name of your disk.
The install program will now ask which file systems should be
created on which partitions. It will automatically select the
'a' partition to be the root file system. Next it will ask for
which disk and partition you want a file system created on.
This will be the same as the disk name (e.g. "sd0") with the
letter identifying the partition (e.g. "d") appended (e.g.
"sd0d"). Then it will ask where this partition is to be
mounted, e.g. /usr. This process will be repeated until you
just hit return.
At this point you will be asked to confirm that the file system
information you have entered is correct, and given an opportunity
to change the file system table. Next it will create the new file
systems as specified, OVERWRITING ANY EXISTING DATA. This is the
point of no return.
The install program will now make the filesystems you specified.
There should be only one error in this section of the installation.
It will look like this:
newfs: ioctl (WDINFO): Invalid argument
newfs: /dev/rsd0a: can't rewrite disk label
If there are any others, restart from the beginning of
the installation process. This error is ok as the Amiga
does not write disklabels currently. You should expect
this error whenever using newfs.
After all your file systems have been created, the install program
will give you an opportunity to configure the network. The network
configuration you enter (if any) can then be used to do the install
from another system using NFS, HTTP or FTP, and will also be the
configuration used by the system after the installation is complete.
If you select to configure the network, the install program will
ask you for a name of your system and the DNS domain name to use.
Note that the host name should be without the domain part, and that
the domain name should NOT {:-include-:} the host name part.
Next the system will give you a list of network interfaces you can
configure. For each network interface you select to configure, it
will ask for the IP address to use, the symbolic host name to use,
the netmask to use and any interface-specific flags to set. The
interface-specific flags are usually used to determine which media
the network card is to use. The flags usually carry the following
meaning:
-link0 -link1 Use BNC (coaxial) port [default]
link0 -link1 Use AUI port
link0 link1 Use UTP (twisted pair) port
After all network interfaces have been configured the install pro-
gram will ask for a default route and IP address of the primary
name server to use. You will also be presented with an opportunity
to edit the host table.
At this point you will be allowed to edit the file system table
that will be used for the remainder of the installation and that
will be used by the finished system, following which the new file
systems will be mounted to complete the installation.
After these preparatory steps has been completed, you will be
able to extract the distribution sets onto your system. There
are several install methods supported; FTP, HTTP, tape, CD-ROM, NFS
or a local disk partition. To install from a tape, the distrib-
ution sets must have been written to tape prior to running the
installation program, either as tar images or as gzipped tar
images. Note that installation from floppies are not currently
supported.
OpenBSDFTPInstall
OpenBSDHTTPInstall
OpenBSDTAPEInstall
OpenBSDCDROMInstall
OpenBSDNFSInstall
OpenBSDDISKInstall({:-"wdN" or -:},,{:- or AmigaDOS FFS (ados)-:})
OpenBSDCommonFS
OpenBSDCommonURL
OpenBSDCongratulations
|
