blob: 3ad6a19476f9ebfca7558362686b20a11fbe3d05 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
|
You will need an AmigaDOS hard drive prep tool to prepare you hard
drives for use with OpenBSD/amiga. HDToolBox is provided with the
system software and on floppy installation disks since Release 2.0
of AmigaDOS so we will provide instructions for its use.
Preparing you hard disk with HDToolBox:
A full explanation of HDToolBox can be found with your
AmigaDOS manuals and is beyond the scope of this document.
Note you will be modifying your HD's if you mess something
up here you could lose everything on all the drives that
you configure. It is therefore advised that you:
Write down your current configurations. Do this
by examining each partition on the drive and the
drives parameters (from Change drive type.)
Back up the partitions you are keeping.
What you need to do is partition your drives; creating at least
root, swap and /usr partitions and possibly at least one more for
/local if you have the space. (The root and swap partitions must
be on the same drive for your initial installation. You can use
other configurations after building a customized kernel once your
system is running.)
This should be done as the HDToolBox manual describes. One thing
to note is that if you are not using a Commodore controller you
will need to specify the device your SCSI controller uses e.g.
if you have a Warp Engine you would:
from cli,
hdtoolbox warpdrive.device
from wb set the tooltype,
SCSI_DEVICE_NAME=warpdrive.device
The important things you need to do above and beyond normal
partitioning includes (from Partition Drive section):
Marking all OpenBSD partitions as non-bootable.
Changing the file system parameters of the partitions
to OpenBSD ones. This must be done from the
partitioning section and `Advanced options' must
be enabled. To Make the needed changes:
- Click the `Adv. Options' button
- Click the `Change filesystem' button
- Choose `Custom File System'
- Turn off `Automount' if on.
- Set the dostype to one of these three choices:
root partition : 0x4e425207
swap partition : 0x4e425301
other partitions: 0x4e425507
Here `other' refers to other partitions you will
format for reading and writing under OpenBSD (e.g.
/usr)
Make sure you hit the return key to enter this value
as some versions of HDToolBox will forget your entry
if you don't.
- Turn custom boot code off
- Set Reserved Blocks start and end to 0.
- Click Ok.
Mask and maxtransfer are not used with OpenBSD.
Until you compile your own kernel your swap partition
must exist on the drive that also holds your root
partition.
Once this is done OpenBSD/amiga will be able to recognize your
disks and which partitions it should use.
Transferring the miniroot filesystem:
The OpenBSD/amiga installation or upgrade now uses a "miniroot"
fileystem which is installed on the partition used by OpenBSD
for swapping. This removes the requirement of using a floppy
disk for the filesystem used by the installation/upgrade
process. It also allows more utilities to be present on the
filesystem than would be available when using an 880K floppy
disk.
Once the hard disk has been prepared for OpenBSD, the miniroot
filesystem (miniroot21.fs) is transferred to the swap partition
configured during the hard disk prep (or the existing swap
partition in the case of an upgrade). The xstreamtodev utility
provided in the "amiga/utilities" directory can be used on
AmigaDOS to transfer the filesystem for either a new installation
or an upgrade. The filesystem can also be transferred on an
existing OpenBSD (or NetBSD) system for an update by using dd.
This should only be done after booting the former OS into single-
user state. It may also be possible to shutdown to single-user,
providing that the single-user state processes are not using the
swap partition.
On AmigaDOS, the command:
xstreamtodev --input=miniroot21.fs --rdb-name=<swap partition>
where <swap partition> is the name you gave to the OpenBSD
partition to be used for swapping. If xstreamtodev is unable to
determine the SCSI driver device name or the unit number of the
specified partition, you may also need to include the option
"--device=<driver.name>" and/or "--unit=<SCSI unit number>".
To transfer the miniroot using an older BSD, you should be booted
up in single user state on the current system, or use the
"shutdown now" command to shutdown to single-uyser state. Then
copy the miniroot using dd:
dd if=miniroot21.fs of=/dev/rsdXb
where /dev/rsdXb should be the device path of the swap partition
your system is configured to use. Once the file is copied,
reboot back to AmigaDOS to boot the new OpenBSD kernel. NOTE:
the release kernel is a "generic" kernel, and requires that the
swap partition be on the same device as the root partition.
|
