1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
|
To do the upgrade, and if you are using the miniroot installation, you
must have the OpenBSD kernel on AmigaDOS and you must transfer the root
filesystem miniroot{:--:}OSrev.fs onto the swap partition of the OpenBSD hard disk.
If you are using the ramdisk installation, the bsd.rd kernel is enough.
You must also have at least the "base{:--:}OSrev" binary distribution set available,
so that you can upgrade with it, using one of the upgrade methods described
above. Finally, you must have sufficient disk space available to install
the new binaries. Since the old binaries are being overwritten in place,
you only need space for the new binaries, which weren't previously
on the system. If you have a few megabytes free on each of your
root and /usr partitions, you should have enough space.
Since upgrading involves replacing the kernel, and most of the system
binaries, it has the potential to cause data loss. You are strongly
advised to BACK UP ANY IMPORTANT DATA ON YOUR DISK, whether on the
OpenBSD partition or on another operating system's partition, before
beginning the upgrade process.
To upgrade your system, follow the following instructions:
If you know you need an -I option to loadbsd, you should add it
to the loadbsd invocation you'll use for the upgrade.
Miniroot installation:
Transfer the upgrade miniroot filesystem onto the hard disk
partition used by OpenBSD for swapping, as described in the
"Preparing your System for OpenBSD Installation" section above.
Now boot up OpenBSD using the OSREV kernel using the loadbsd
command:
loadbsd -b bsd
You should see the screen clear and some information about
your system as the kernel configures the hardware. Note which
hard disk device is configured that contains your root and
swap partition. When prompted for the root device, type
'sd0*' (replacing 0 with the disk number that OpenBSD used for
your root/swap device). The '*' character indicates that the
root filesystem is contained on the swap partition. Continue
reading below the ramdisk installation description:
Ramdisk installation:
Now boot up OpenBSD using the OSREV kernel using the loadbsd
command:
loadbsd bsd.rd
You should see the screen clear and some information about
your system as the kernel configures the hardware.
Common instructions for both miniroot/ramdisk installations:
When you reach the prompt asking you for a shell name, just
hit return.
You will be asked which terminal type to use, you should just
hit return to select the default (vt220).
At the question whether to (I)nstall or (U)pgrade choose "U".
You will be presented with some information about the upgrade
process and a warning message, and will be asked if you wish
to proceed with the upgrade process. If you answer
negatively, the upgrade process will stop, and your disk will
not be modified. If you answer affirmatively, the upgrade
process will begin, and your disk will be modified. You may
hit Control-C to stop the upgrade process at any time.
However, if you hit it at an inopportune moment, your system
may be left in an inconsistent (and possibly unusable) state.
The upgrade program will then check & mount your root filesystem
under /mnt and grab some configuration info from it for the
continued upgrade process. You'll be asked if the network
should be enabled at this point. After that is done the rest
of the filesystems will be checked and mounted.
If you don't already have the OpenBSD distribution sets on your
disk, look in the installation section for information on how
to transfer them to your disk.
Once the distribution sets are transferred to your disk,
continue here. (Obviously, if the OpenBSD distribution sets
are already on your disk, because you've transferred them
before starting the upgrade process, you don't need to
transfer them again now!)
After the software has been transferred to the machine (or
mounted, in the case of upgrading via NFS).
Your system has now been upgraded to OpenBSD OSREV.
After all this, your machine is a complete OpenBSD OSREV system.
However, that doesn't mean that you're finished with the upgrade
process. There are several things that you should do, or might
have to do, to insure that the system works properly.
First, you will probably want to get the etc{:--:}OSrev.tgz distribution,
extract it, and compare its contents with those in your /etc/
directory. You will probably want to replace some of your
system configuration files, or incorporate some of the changes
in the new versions into yours.
Second, you might want to check your /dev against the new MAKEDEV
script found there, if you have changed the nodes locally. The
upgrade process runs "sh MAKEDEV all" but that may not be enough
for your personal setup.
Third, you must deal with certain changes in the formats of
some of the configuration files. The most notable change is
that the "options" given to many of the file systems in
/etc/fstab or by hand have changed, and some of the file
systems have changed names. To find out what the new options
are, it's suggested that you read the manual page for the
file systems' mount commands, for example mount_nfs(8) for
NFS. (Note that the information for mounts of type "ufs",
i.e. Fast File Systems, are contained in the mount(8) man
page.)
Finally, you will want to delete old binaries that were part
of the version of OpenBSD that you upgraded from and have since
been removed from the OpenBSD distribution. You might also
want to recompile any locally-built binaries, to take
advantage of the shared libraries. (Note that any new
binaries that you build will be dynamically linked, and
therefore take advantage of the shared libraries, by default.
For information on how to make statically linked binaries,
see the cc(1) and ld(1) manual pages.)
|
