1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
|
Installation is supported from several media types, including:
AmigaDOS HD partitions
Tape
NFS partitions
FTP
OpenBSD partitions, if doing an upgrade.
The install or upgrade miniroot filesystem needs to be transferred
to the OpenBSD swap partition. This can be done from AmigaDOS in
the case of a new install or upgrade, or from OpenBSD when doing an
upgrade. See the "Preparing your System for OpenBSD Installation"
section for details.
The steps necessary to prepare the distribution sets
for installation depend on which method of installation
you choose. The various methods are explained below.
To prepare for installing via an AmigaDOS partition:
To install OpenBSD from an AmigaDOS partition, you need to
get the OpenBSD distribution sets you wish to install
on your system on to an AmigaDOS partition. All of the
set_name.xx pieces can be placed in a single directory
instead of separate ones for each distribution set. This
will also simplify the installation work later on.
Note where you place the files you will need this later.
Once you have done this, you can proceed to the next
step in the installation process, preparing your hard disk.
To prepare for installing via a tape:
To install OpenBSD from a tape, you need to somehow
get the OpenBSD filesets you wish to install on
your system on to the appropriate kind of tape,
in tar format.
If you're making the tape on a UN*X system, the easiest
way to do so is:
tar cvf <tape_device> <files>
where "<tape_device>" is the name of the tape device
that describes the tape drive you're using (possibly
something like /dev/nrst0, but we make no guarantees 8-).
If you can't figure it out, ask your system administrator.
"<files>" are the names of the "set_name.nnn" files
which you want to be placed on the tape.
Once you have done this, you can proceed to the next
step in the installation process, preparing your hard disk.
To prepare for installing via an NFS partition:
NOTE: this method of installation is recommended
only for those already familiar with using
the BSD network-manipulation commands and
interfaces. If you aren't, this documentation
should help, but is not intended to be
all-encompassing.
Place the OpenBSD software you wish to install into
a directory on an NFS server, and make that directory
mountable by the machine which you will be installing
OpenBSD on. This will probably require modifying the
/etc/exports file of the NFS server and resetting
mountd, acts which will require superuser privileges.
Note the numeric IP address of the NFS server and of
the router closest to the the new OpenBSD machine,
if the NFS server is not on a network which is
directly attached to the OpenBSD machine.
Once you have done this, you can proceed to the next
step in the installation process, preparing your hard disk.
To prepare for installing via FTP:
NOTE: this method of installation is recommended
only for those already familiar with using
the BSD network-manipulation commands and
interfaces. If you aren't, this documentation
should help, but is not intended to be
all-encompassing.
The preparations for this method of installation
are easy: all you have to do is make sure that
there's some FTP site from which you can retrieve
the OpenBSD installation when it's time to do
the install. You should know the numeric IP
address of that site, the numeric IP address of
your nearest router if one is necessary
Once you have done this, you can proceed to the next
step in the installation process, preparing your hard disk.
If you are upgrading OpenBSD, you also have the option of installing
OpenBSD by putting the new distribution sets somewhere in your existing
file system, and using them from there. To do that, you must do the
following:
Place the distribution sets you wish to upgrade somewhere in
your current file system tree. At a bare minimum, you must
upgrade the "base" binary distribution, and so must put the
"base11" set somewhere in your file system. If you wish,
you can do the other sets, as well, but you should NOT upgrade
the "etc" distribution; the "etc" distribution contains system
configuration files that you should review and update by hand.
Once you have done this, you can proceed to the next step in
the upgrade process, actually upgrading your system.
|
