1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
|
The ramdisk kernel may be loaded from the network, from CD-ROM, or other
SCSI devices (such as Zip(tm) disk). This section primarily describes the
setup required for a network boot, but does offer information pertaining to
installation from other media. Note that loading from HPIB or SCSI cartridge
tape is possible, but not currently supported.
You will need information about your disk's geometry, based on 512-byte
sectors. You must have this information before proceeding. The
file `HP-IB.geometry' has geometry information for several HP-IB disks,
but may be incomplete. Geometry may be calculated from an HP-UX
`/etc/disktab' entry, but note that HP-UX geometry is based on
1024 byte sectors, while OpenBSD's is based on 512 byte sectors.
QUICK NOTE ABOUT PARTITIONS: Since the target disk will become the boot
disk for your new OpenBSD/hp300 installation, you will need to treat the
`a' and `c' partitions in a special manner. Due to the size of the
OpenBSD/hp300 boot program (it spills into the area after the disklabel),
it is necessary to offset the `a' partition one cylinder from the beginning
of the disk. Later, the `c' partition will be marked with the type
`FS_BOOT' and may not be used for a filesystem. (For those unfamiliar
with historic BSD partition conventions, the `c' partition is defined
as `the entire disk', or the `raw partition'.)
Ramdisk installation via network or CD-ROM
------------------------------------------
NOTE: BOOTING SYS_UBOOT VIA THE NETWORK IS ONLY POSSIBLE IF YOUR BOOTROM
IS `REV. C' OR LATER.
In order to complete this process, you will need the following from the
`2.2/hp300' directory of the distribution:
SYS_UBOOT The unified boot block file.
bsd.rd The gzipped RAMDISK kernel image.
To boot SYS_UBOOT via the network, you will need a system capable of
handling boot requests for an hp300. If you will use this method, see
the special note below.
To boot from SCSI CD-ROM, simply insert the CD that is hp300 bootable into
the drive before power up, then during the client's self-test cycle,
press the space bar. Shortly, you should see a menu of possible boot
options appear. Select the option corresponding to SYS_CDROM.
SYS_UBOOT will then load and prompt you for a kernel name.
-- The following section is specific for loading SYS_UBOOT via the network. --
If you wish to load the SYS_UBOOT program via the network, you need to
either have another OpenBSD system on the network, or something else
capable of running the rbootd(8) program. Source code may be found
under usr.sbin/rbootd in the OpenBSD source tree, but requires the
Berkeley Packet Filter (bpf) in order to function. It may be possible to
use HP-UX, but is not recommended (or documented here).
First of all, configure your rbootd to handle boot requests from the
client. NOTE: OpenBSD's `rbootd' is slightly different from HP-UX's.
To configure OpenBSD's `rbootd', create a file called `/etc/rbootd.conf'
and place in it an entry like the following:
08:00:09:04:AA:33 SYS_UBOOT # thunder-egg
The first column is the ethernet address of the client's network interface.
The second column is the program to send to the client, and anything after
the `#' is a comment. Once you have rbootd running, copy the SYS_UBOOT
program to the /usr/mdec/rbootd directory on your server. If this
directory doesn't exist already, you will need to create it.
For information on configuring rbootd under HP-UX, see the rbootd(1M)
manual page on your server system.
Once `rbootd' is configured and running, you will be ready to continue.
Make sure that the ramdisk kernel image (`bsd.rd') resides in a filesystem
that is NFS exported to the client. See the manual pages on your server
system if you need more information about exporting filesystems.
You are now ready to load SYS_UBOOT. During the client's self-test cycle,
press the space bar. Shortly, you should see a menu of possible boot
options appear. Select the option corresponding to SYS_UBOOT.
SYS_UBOOT will then load and prompt you for a kernel name. NFS file
names should not have a leading '/' prepended to them, simply use `bsd.rd'.
------------------ End of network boot-specific section ----------------------
|