1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
|
dnl $OpenBSD: install,v 1.28 2020/05/17 17:04:28 deraadt Exp $
dnl lots of texts coming from {mvme68k,vax}/install initially
OpenBSDInstallPrelude
Bootstrapping the installation ramdisk kernel is supported
from either the network or a CD-ROM.
Booting from CD-ROM installation media:
To boot from SCSI CD-ROM, simply insert the CD into the drive before power
up, then during the computer's self-test cycle, press the space bar.
Subsequently at the PROM prompt issue a command:
BOOT_ADMIN> search
to initiate a search for all bootable devices available. This procedure
may take a few minutes and should you have configured network boot services
present may find those too. A sample output might be:
Path Number Device Path Device Type
----------- ----------------- -----------
P0 SESCSI.2.0 TOSHIBA CD-ROM XM-6201TA
P1 LAN.10.0.0.5.3.254 boron
P2 FWSCSI.5.0 IBM DDRS-34560WS
P3 FWSCSI.0.0 SEAGATE ST318436LW
P4 SESCSI.6.0 HP HP35480A
To boot from your CD-ROM type:
BOOT_ADMIN> boot p0
Booting from Network:
In order to bootstrap via the network, you must provide a second system to
act as a boot server. It is convenient if this is a second OpenBSD machine
as the necessary services are already installed, although source code for
such programs as dhcpd can be found in OpenBSD's source tree, and should be
reasonably portable to other Unix-like operating systems. More information
on diskless booting can be found in the OpenBSD diskless(8) manual page.
Your MACHINE expects to be able to download a LIF (``Logical
Interchange Format'') image, containing both the boot code and the kernel,
via the HP rboot protocol, for older firmware, or via the bootp protocol,
for more recent firmware.
Old firmware operation
Most of the 7xx models (except the 712, the second generation of 715, i.e.
715/64/80/100/100XC, and the 74x) have an older version of PDC. There are
two levels of interactive commands in this version.
The first level is a short menu:
b) Boot from specified device
s) Search for bootable device
a) Enter Boot Administration mode
x) Exit and continue boot sequence
Select from menu:
In this case, you will need to setup rbootd on the server. Start by
creating an /etc/rbootd.conf file on the bootserver. The format of this
file is the ethernet address followed by the LIF filename. Here is an
example:
08:00:09:70:c4:11 lif{:--:}OSrev.img
Then start rbootd (or configure /etc/rc.conf to always start rbootd). Once
rbootd is running, the server name will then appear on the MACHINE as part
of the possible boot choices in a boot device search (``s'' command).
Modern firmware operation
More recent machines mostly those based on the 7100LC, 7200 and 7300LC CPU
types have a different PDC version. There is only one interactive mode,
with a BOOT_ADMIN> prompt, which provides both boot settings and commands.
In this case, you will need to set up dhcpd on the server, which can
serve bootp protocol requests. Start by editing the /etc/dhcpd.conf on
the bootserver, and declare an information block. Here is an example:
subnet 10.0.0.0 netmask 255.0.0.0 {
host boron {
filename "lif{:--:}OSrev.img";
hardware ethernet 08:00:09:70:c4:11;
fixed-address 10.42.42.42;
}
}
Do not forget to enable dhcpd.
You will also need to enable tftpd, for the MACHINE to download the
installation kernel (`filename' entry) from the server in its tftp
directory.
Common operation
You are now ready to bootstrap the installation kernel. On your machine,
escape to a prompt and boot from the network by entering ``boot lan isl''.
On old PDC firmware, you will need to enter administration mode first.
Installing using the netboot procedure:
OpenBSDInstallPart2
Boot your machine from the installation media as described above.
It will take a while to load the installation kernel, especially from
a slow network connection or a CD-ROM, most likely more than a minute.
If some action doesn't eventually happen, or the spinning cursor
has stopped and nothing further has happened, either your boot
media is bad, your diskless setup is incorrect, or you may have
a hardware or configuration problem.
OpenBSDInstallPart3(,"sd0")
OpenBSDInstallPart4
OpenBSDInstallPart5(,{:-
Due to prom limitations, you should make sure the whole 'a'
partition is CONTAINED WITHIN THE FIRST 2GB of the disk if
you intend to boot from it.-:})
Since the target disk will become the boot disk for your new
OpenBSD/MACHINE installation, the disklabel program will restrict
the available disk area to keep the first cylinder, which will
contain the bootblock, safe from being overwritten. If you don't
plan to install a bootblock on this disk, you can reclaim this
space with the 'b' command.
OpenBSDInstallPart6({:-CD-ROM, -:})
OpenBSDURLInstall
OpenBSDCDROMInstall
OpenBSDNFSInstall
OpenBSDDISKInstall(,{:-only -:})
OpenBSDCommonInstall
OpenBSDInstallWrapup
OpenBSDCongratulations
OpenBSDUnattendedInstallation
|