1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
|
dnl $OpenBSD: install,v 1.34 2002/04/09 01:22:22 miod Exp $
OpenBSDInstallPrelude
If OpenBSD will be sharing the disk with DOS or another operating
system, you should have already completed the section of these notes
that instructed you on how to prepare your hard disk. You should know
the size of the OpenBSD area of the disk and its offset from the
beginning of the disk. You will need this information when setting up
your OpenBSD partitions. If your BIOS uses translated geometry, you
should use this geometry for the remainder of the install. This is
only necessary if you are sharing the disk with other operating systems
that use the translated geometry.
There are several ways to install OpenBSD onto a disk. The easiest way,
should your computer support it, is to boot off the CD-ROM. Otherwise,
you can boot from a 3.5" 1.44MB floppy disk.
OpenBSDInstallPart2
With either the CD-ROM or the floppy in the drive, reboot your
computer. You might have to play with your BIOS options to let the
computer boot from the installation media, rather than the hard
disk.
It will take a while to load the kernel from a floppy or slow
speed CD-ROM drive, most likely more than a minute. If some
action doesn't eventually happen, or the spinning cursor has
stopped and nothing further has happened, either your boot floppy
is bad or you are having hardware problems. If trying another
floppy disk doesn't help, try booting after disabling your CPU's
internal and external caches (if any). If it still doesn't work,
OpenBSD probably can't be run on your hardware. This can probably
be considered a bug, so you might want to report it.
If you do, please {:-include-:} as many details about your system
configuration as you can.
OpenBSDBootMsgs
You will next be asked for your terminal type. You should just
hit return to select the default (vt220).
OpenBSDInstallPart3({:- or "wd0" for IDE/RLL/ESDI/ST506 drives-:})
Next you will have to edit or create a disk label for the disk
OpenBSD is being installed on. If there are any existing
partitions defined (for any operating system), and a disk label
is not found, you will first be given an opportunity to run
fdisk and create an OpenBSD partition.
If fdisk is being invoked on your behalf, it will start by
displaying the current partitions defined and then allow you
to modify this information, add new partitions and change
which partition to boot from by default. If you make a mistake,
you will be allowed to repeat this procedure as necessary to
correct this. Note that you should make OpenBSD be the active
partition at least until the install has been completed.
OpenBSDInstallPart4({:- If you have DOS or Linux partitions
defined on the disk, these will usually show up as partition
'h', 'i' and so on.-:})
Note that all OpenBSD partitions in the disk label must have an
offset that makes it start within the OpenBSD part of the disk,
and a size that keeps it inside of that portion of the disk. This
is within the bounds of the 'c' partition if the disk is not being
shared with other operating systems, and within the OpenBSD fdisk
partition if the disk is being shared.
OpenBSDInstallPart5(wd0)
OpenBSDInstallNet({:-CD-ROM, -:},nofloppy)
OpenBSDFTPInstall
OpenBSDHTTPInstall
OpenBSDTAPEInstall
OpenBSDCDROMInstall
OpenBSDDISKInstall({:-"wdN" or -:},,{:- or MS-DOS-:})
OpenBSDCommonFS
OpenBSDCommonURL
OpenBSDCongratulations
|
