1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
|
/* $OpenBSD: params.h,v 1.6 2001/08/16 20:02:42 camield Exp $ */
/*
* Global POP daemon parameters.
*/
#ifndef _POP_PARAMS_H
#define _POP_PARAMS_H
/*
* Are we going to be a standalone server or start via an inetd clone?
*/
#define POP_STANDALONE 1
#if POP_STANDALONE
/*
* The address and port to listen on.
*/
#define DAEMON_ADDR "0.0.0.0" /* INADDR_ANY */
#define DAEMON_PORT 110
/*
* Limit the number of POP sessions we can handle at a time to reduce
* the impact of connection flood DoS attacks.
*/
#define MAX_SESSIONS 100
#define MAX_SESSIONS_PER_SOURCE 10
#define MAX_BACKLOG 5
#define MIN_DELAY 10
#endif
/*
* Do we want to support virtual domains?
*/
#define POP_VIRTUAL 0
#if POP_VIRTUAL
/*
* VIRTUAL_HOME_PATH is where the virtual domain root directories live.
*/
#define VIRTUAL_HOME_PATH "/vhome"
/*
* Subdirectories within each virtual domain root for the authentication
* information and mailboxes, respectively. These defaults correspond to
* full pathnames of the form "/vhome/IP/{auth,mail}/username".
*/
#define VIRTUAL_AUTH_PATH "auth"
#define VIRTUAL_SPOOL_PATH "mail"
/*
* Do we want to support virtual domains only? Normally, if the connected
* IP address doesn't correspond to a directory in VIRTUAL_HOME_PATH, the
* authentication will be done globally.
*/
#define VIRTUAL_ONLY 0
#else
/*
* We don't support virtual domains (!POP_VIRTUAL), so we're definitely
* not virtual-only. Don't edit this.
*/
#define VIRTUAL_ONLY 0
#endif
/*
* An unprivileged dummy user to run as before authentication. The user
* and its UID must not be used for any other purpose.
*/
#define POP_USER "popa3d"
/*
* Sessions will be closed if idle for longer than POP_TIMEOUT seconds.
* RFC 1939 says that "such a timer MUST be of at least 10 minutes'
* duration", so I've made 10 minutes the default. In practice, you
* may want to reduce this to, say, 2 minutes.
*/
#define POP_TIMEOUT (10 * 60)
/*
* Do we want to support the obsolete LAST command, as defined in RFC
* 1460? It has been removed from the protocol in 1994 by RFC 1725,
* and isn't even mentioned in RFC 1939. Still, some software doesn't
* work without it.
*/
#define POP_SUPPORT_LAST 1
/*
* Introduce some sane limits on the mailbox size in order to prevent
* a single huge mailbox from stopping the entire POP service.
*/
#define MAX_MAILBOX_MESSAGES 100000
#define MAX_MAILBOX_BYTES 100000000
#if !VIRTUAL_ONLY
/*
* Choose the password authentication method your system uses:
*
* AUTH_PASSWD Use getpwnam(3) only, for *BSD or readable passwd;
*
* Note that there's no built-in password aging support.
*/
#define AUTH_PASSWD 1
#endif
#if POP_VIRTUAL || AUTH_PASSWD
/*
* A salt used to waste some CPU time on dummy crypt(3) calls and make
* it harder (but still far from impossible, on most systems) to check
* for valid usernames. Adjust it for your crypt(3).
*/
/* echo -n "dummyblowfishsalt" | encrypt -b 7 */
#define AUTH_DUMMY_SALT "$2a$07$deZMiFIouL0vgRsEG.AJY.Jx2Z8wJj3g5qs11UQWrBj8MERIu/rXi"
#endif
/*
* Message to return to the client when authentication fails. You can
* #undef this for no message.
*/
#define AUTH_FAILED_MESSAGE "Authentication failed (bad password?)"
#if !VIRTUAL_ONLY
/*
* Your mail spool directory. Note: only local (non-NFS) mode 775 mail
* spools are currently supported.
*/
#define MAIL_SPOOL_PATH "/var/mail"
#endif
/*
* Locking method your system uses for user mailboxes. It is important
* that you set this correctly.
*/
#define LOCK_FCNTL 1
#define LOCK_FLOCK 0
/*
* How do we talk to syslogd? These should be fine for most systems.
*/
#define SYSLOG_IDENT "popa3d"
#define SYSLOG_OPTIONS LOG_PID
#define SYSLOG_FACILITY LOG_DAEMON
#define SYSLOG_PRIORITY LOG_NOTICE
/*
* There's probably no reason to touch anything below this comment.
*/
/*
* According to RFC 1939: "Keywords and arguments are each separated by
* a single SPACE character. Keywords are three or four characters long.
* Each argument may be up to 40 characters long." We're only processing
* up to two arguments, so it is safe to truncate after this length.
*/
#define POP_BUFFER_SIZE 0x80
/*
* There's no reason to change this one either. Making this larger would
* waste memory, and smaller values could make the authentication fail.
*/
#define AUTH_BUFFER_SIZE (2 * POP_BUFFER_SIZE)
#if POP_VIRTUAL
/*
* Buffer size for reading entire per-user authentication files.
*/
#define VIRTUAL_AUTH_SIZE 0x100
#endif
/*
* File buffer sizes to use while parsing the mailbox and retrieving a
* message, respectively. Can be changed.
*/
#define FILE_BUFFER_SIZE 0x10000
#define RETR_BUFFER_SIZE 0x8000
/*
* The mailbox parsing code isn't allowed to truncate lines earlier than
* this length. Keep this at least as large as the longest header field
* name we need to check for, but not too large for performance reasons.
*/
#define LINE_BUFFER_SIZE 0x20
#endif
|
