blob: e01bb8527228f9148e8ff67e1bfd9b7e27af9134 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
|
#!/bin/sh
# $OpenBSD: rc.vpn,v 1.17 2002/12/05 12:50:03 markus Exp $
#
# Richard Reiner, Ph.D., FSC Internet Corp.
# rreiner@fscinternet.com
# v0.81 / 26Jul98
#
# Modifications and cleanup by H. Olsson <ho@openbsd.org>, 28Aug99
# and Markus Friedl <markus@openbsd.org>
#
# rc.vpn -- configure IPsec in tunnel mode for a mesh of N local and
# M remote networks. (N x M mesh)
#
# For this to work, you will need to have these enabled (in /etc/sysctl.conf):
# 'sysctl -w net.inet.ip.forwarding=1' (IP packet routing)
# 'sysctl -w net.inet.esp.enable=1' (IPsec ESP protocol)
# XXX The configuration parameters should be moved to another file.
# Uncomment to debug (and not execute) commands
#DEBUG=echo
# Gateway adresses
GW_LOCAL=192.168.254.254
GW_REMOTE=192.168.1.2
# Local and remote networks
LOCAL_NETWORKS="192.168.254.0/24 192.168.253.0/24"
REMOTE_NETWORKS="192.168.1.0/24 192.168.2.0/24"
# Optional, use for manual keying only
# Crypto options and keys, note that key/iv lengths need to correspond
# to the selected encryption and authentication algorithms.
ENC=3des
AUTH=sha1
SPI_OUT=1000
SPI_IN=1001
KEYFILE=/etc/esp-enc-key
AUTHKEYFILE=/etc/esp-auth-key
#############################################################################
############# -- NO CHANGES SHOULD BE NEEDED BELOW THIS LINE -- #############
#############################################################################
ipsecadm=/sbin/ipsecadm
#
# Sanity, be verbose about errors.
# XXX In a 1 x M mesh, ip.forwarding may not be strictly necessary.
#
abort=0
if [ `/usr/sbin/sysctl -n net.inet.esp.enable` == 0 ]; then
echo "$0: variable 'net.inet.esp.enable=0' (IPsec ESP protocol)"
abort=1
fi
if [ `/usr/sbin/sysctl -n net.inet.ip.forwarding` == 0 ]; then
echo "$0: variable 'net.inet.ip.forwarding=0' (IP forwarding/routing)"
abort=1
fi
if [ ${abort} = 1 ]; then
echo "$0: must be enabled in /etc/sysctl.conf. Aborting VPN setup."
[ ! -n "${DEBUG}" ] && exit 0
fi
$DEBUG $ipsecadm flush
#
# Setup the manual SAs
#
if [ "$ENC" ]; then
$DEBUG $ipsecadm new esp -src $GW_LOCAL -dst $GW_REMOTE \
-forcetunnel -spi $SPI_OUT -enc $ENC -auth $AUTH \
-keyfile $KEYFILE -authkeyfile $AUTHKEYFILE
$DEBUG $ipsecadm new esp -src $GW_REMOTE -dst $GW_LOCAL \
-forcetunnel -spi $SPI_IN -enc $ENC -auth $AUTH \
-keyfile $KEYFILE -authkeyfile $AUTHKEYFILE
fi
#
# Setup the Flows, aka SPD
#
# add the gateways
LOCAL_NETWORKS="${GW_LOCAL}/32 ${LOCAL_NETWORKS}"
REMOTE_NETWORKS="${GW_REMOTE}/32 ${REMOTE_NETWORKS}"
FLOW="$DEBUG ${ipsecadm} flow -proto esp -src ${GW_LOCAL} -dst ${GW_REMOTE} -require"
# each local net to each remote net
for local_net in ${LOCAL_NETWORKS}; do
for remote_net in ${REMOTE_NETWORKS}; do
$FLOW -out -addr $local_net $remote_net
$FLOW -in -addr $remote_net $local_net
done
done
exit 0
|
