1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
|
/* $OpenBSD: dioreg.h,v 1.6 2010/04/15 20:38:09 miod Exp $ */
/* $NetBSD: dioreg.h,v 1.3 1997/01/30 09:18:40 thorpej Exp $ */
/*-
* Copyright (c) 1996 The NetBSD Foundation, Inc.
* All rights reserved.
*
* This code is derived from software contributed to The NetBSD Foundation
* by Jason R. Thorpe.
*
* Portions of this file are derived from software contributed to Berkeley
* by the Systems Programming Group of the University of Utah Computer
* Science Department.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
* TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE
* LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*/
/*
* Register definitions for the DIO and DIO-II bus.
*/
/*
* DIO/DIO-II device registers, offsets from base of device. All
* registers are 8-bit.
*/
#define DIO_IDOFF 0x01 /* primary device id */
#define DIO_IPLOFF 0x03 /* interrupt level */
#define DIO_SECIDOFF 0x15 /* secondary device id */
#define DIOII_SIZEOFF 0x101 /* device size */
/*
* System physical addresses of some `special' DIO devices.
*/
#define DIO_IHPIBADDR 0x478000 /* internal HP-IB; select code 7 */
/*
* DIO ranges from select codes 0-63 at physical addresses given by:
* 0x600000 + (sc - 32) * 0x10000
* DIO cards are addressed in the range 0-31 [0x600000-0x800000) for
* their control space and the remaining areas, [0x200000-0x400000) and
* [0x800000-0x1000000), are for additional space required by a card;
* e.g. a display framebuffer.
*
* DIO-II ranges from select codes 132-255 at physical addresses given by:
* 0x1000000 + (sc - 132) * 0x400000
* The address range of DIO-II space is thus [0x1000000-0x20000000).
*
* DIO/DIO-II space is too large to map in its entirety, instead devices
* are mapped into kernel virtual address space allocated from a range
* of EIOMAPSIZE pages (vmparam.h) starting at ``extiobase''.
*/
#define DIO_BASE 0x600000 /* start of DIO space */
#define DIO_END 0x1000000 /* end of DIO space */
#define DIO_DEVSIZE 0x10000 /* size of a DIO device */
#define DIOII_BASE 0x01000000 /* start of DIO-II space */
#define DIOII_END 0x20000000 /* end of DIO-II space */
#define DIOII_DEVSIZE 0x00400000 /* size of a DIO-II device */
/*
* Find the highest select code for a given machine; HP320 doesn't
* have DIO-II.
*/
#if defined(HP320)
#define DIO_SCMAX(machineid) ((machineid) == HP_320 ? 32 : 256)
#else
#define DIO_SCMAX(machineid) 256
#endif
/*
* Base of DIO-II select codes.
*/
#define DIOII_SCBASE 132
/*
* Macros to determine if device is DIO or DIO-II.
*/
#define DIO_ISDIO(scode) ((scode) >= 0 && (scode) < 32)
#define DIO_ISDIOII(scode) ((scode) >= DIOII_SCBASE && (scode) < 256)
/*
* Macro to determine if device is a framebuffer, given the
* primary id of the device. We key off this to determine if
* we should look at secondary id and ignore interrupt level.
*/
#define DIO_ISFRAMEBUFFER(id) \
((id) == DIO_DEVICE_ID_FRAMEBUFFER)
/*
* Macro to extract primary and decondary device ids, given
* the base address of the device.
*/
#define DIO_ID(base) \
(*((u_int8_t *)((u_long)(base) + DIO_IDOFF)))
#define DIO_SECID(base) \
(*((u_int8_t *)((u_long)(base) + DIO_SECIDOFF)))
/*
* Macro to extract the interrupt level, given the
* base address of the device.
*/
#define DIO_IPL(base) \
((((*((u_int8_t *)((u_long)(base) + DIO_IPLOFF))) >> 4) & 0x03) + 3)
/*
* Macro to compute the size of a DIO-II device's address
* space, given the base address of the device.
*/
#define DIOII_SIZE(base) \
((int)((*((u_int8_t *)((u_long)(base) + DIOII_SIZEOFF)) + 1) \
* 0x100000))
/*
* Given a select code and device base address, compute
* the size of the DIO/DIO-II device.
*/
#define DIO_SIZE(scode, base) \
(DIO_ISDIOII((scode)) ? DIOII_SIZE((base)) : DIO_DEVSIZE)
|
