1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
|
# $OpenBSD: SMD_TEST,v 1.15 2001/03/08 03:37:20 itojun Exp $
# $NetBSD: SMD_TEST,v 1.2.4.1 1996/08/19 23:35:11 gwr Exp $
#
# SMD_TEST - for Sun3 (3/50, 3/60, 3/110, 3/160, 3/260)
#
# machine architecture; required by config(8)
machine sun3 m68k
include "../../../conf/GENERIC"
# Options for some specific Sun3 models
option FPU_EMULATE # for 3/50 models without FPU
option HAVECACHE # for 3/260 VAC
maxusers 4 # estimated number of users
config bsd swap generic
# The root node:
mainbus0 at root
# device space
obio0 at mainbus?
# main memory
obmem0 at mainbus?
# VME D16 space
vmes0 at mainbus?
# VME D32 space
vmel0 at mainbus?
# Devices that should be present in any Sun3 kernel.
# OBIO
zsc0 at obio0 addr 0x000000
zsc1 at obio0 addr 0x020000
eeprom0 at obio0 addr 0x040000
clock0 at obio0 addr 0x060000
memerr0 at obio0 addr 0x080000
intreg0 at obio0 addr 0x0A0000
#
# Serial ports
#
zstty0 at zsc1 channel 0 # ttya
zstty1 at zsc1 channel 1 # ttyb
kbd0 at zsc0 channel 0 # keyboard
ms0 at zsc0 channel 1 # mouse
#
# Network devices
#
# Intel Ethernet (onboard, or VME)
ie0 at obio0 addr 0x0C0000 level 3
ie1 at vmes0 addr 0xffe88000 level 3 vect 0x75
# Lance Ethernet (only onboard)
le0 at obio0 addr 0x120000 level 3
# All Sun3 machines with an "le" (3/50, 3/60) should be
# presumed to have the old, buggy LANCE chip. (Rev. C)
options LANCE_REVC_BUG
#
# Disk and tape devices
#
# Sun3 "si" SCSI controller (NCR 5380)
# This driver has several flags which may be enabled by OR'ing
# the values and using the "flags" directive. (PR#1929)
# Valid flags are:
#
# 0x01 Use DMA (may be polled)
# 0x02 Use DMA completion interrupts
# 0x04 Allow disconnect/reselect
#
# E.g. "flags 0x07" would enable DMA, interrupts, and reselect.
# Note: these values are quite a bit paranoid...
si0 at obio0 addr 0x140000 level 2 flags 0x07
si0 at vmes0 addr 0xff200000 level 2 vect 0x40 flags 0x07
si1 at vmes0 addr 0xff204000 level 2 vect 0x41 flags 0x07
# Xylogics 7053 controllers
xdc0 at vmel0 addr 0xffffee80 level 2 vect 0x44
xdc1 at vmel0 addr 0xffffee90 level 2 vect 0x45
xd* at xdc? drive ?
# Xylogics 450/451 controllers
xyc0 at vmes0 addr 0xffffee40 level 2 vect 0x48
xyc1 at vmes0 addr 0xffffee48 level 2 vect 0x49
xy* at xyc? drive ?
# Xylogics 472 tape controllers?
#
# Frame buffer devices
#
# The default cgfour address depends on the machine:
# 3/60: obmem 0xFF200000 .. 0xFF9fffff
# 3/110: different? (not tested)
cgfour0 at obmem0 addr ?
# 3/60 P4 accelerated 8-bit color frame buffer
# cgsix0 at obmem0 addr ?
# 3/60 P4 24-bit color frame buffer
# cgeight0 at obmem0 addr ?
# The default bwtwo address depends on the machine:
# 3/50: obmem 0x100000
# else: obmem 0xff000000
bwtwo0 at obmem0 addr ?
# 3/60 P4 color frame buffer overlay plane, or P4 monochrome frame buffer
#bwtwo1 at obmem0 addr 0xff300000
# 3/60 plug-in color frame buffer overlay plane
#bwtwo1 at obmem0 addr 0xff400000
# Sun-3 color board, or CG5 8-bit VME frame buffer.
cgtwo0 at vmes0 addr 0xff400000 level 4 vect 0xA8
# Support for the CG9 24-bit VME frame buffer.
# cgnine0 at vmel0 addr 0x08000000
#
# SCSI infrastructure
#
scsibus* at scsi?
sd* at scsibus? target ? lun ?
st* at scsibus? target ? lun ?
cd* at scsibus? target ? lun ?
ch* at scsibus? target ? lun ?
ss* at scsibus? target ? lun ?
uk* at scsibus? target ? lun ?
# Networking options
# XXX - Work-around for root on slow SunOS/Sun3 servers (sigh...)
option NFS_BOOT_RWSIZE=1024
# Compatibility options
option COMPAT_SUNOS # can run SunOS 4.1.1 executables
# Sun3-specific debugging options
option PMAP_DEBUG
#option VMFAULT_TRACE
#option SYSCALL_DEBUG
#option EXEC_DEBUG
#option SCSIDEBUG
|
