1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
|
/* $OpenBSD: comreg.h,v 1.14 2005/07/03 19:46:45 deraadt Exp $ */
/* $NetBSD: comreg.h,v 1.8 1996/02/05 23:01:50 scottr Exp $ */
/*
* Copyright (c) 1997 - 1998, Jason Downs. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR(S) ``AS IS'' AND ANY EXPRESS
* OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE AUTHOR(S) BE LIABLE FOR ANY DIRECT,
* INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*/
/*-
* Copyright (c) 1991 The Regents of the University of California.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. Neither the name of the University nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* @(#)comreg.h 7.2 (Berkeley) 5/9/91
*/
#include <dev/ic/ns16550reg.h>
#ifndef COM_FREQ /* allow to be set externally */
#define COM_FREQ 1843200 /* 16-bit baud rate divisor */
#endif
#define COM_TOLERANCE 30 /* baud rate tolerance, in 0.1% units */
/* interrupt enable register */
#define IER_ERXRDY 0x1 /* Enable receiver interrupt */
#define IER_ETXRDY 0x2 /* Enable transmitter empty interrupt */
#define IER_ERLS 0x4 /* Enable line status interrupt */
#define IER_EMSC 0x8 /* Enable modem status interrupt */
#define IER_SLEEP 0x10 /* Enable sleep mode */
/* PXA2X0's ns16550 ports have extra bits in this register */
#define IER_ERXTOUT 0x10 /* Enable rx timeout interrupt */
#define IER_EUART 0x40 /* Enable UART */
/* interrupt identification register */
#define IIR_IMASK 0xf
#define IIR_RXTOUT 0xc
#define IIR_RLS 0x6 /* Line status change */
#define IIR_RXRDY 0x4 /* Receiver ready */
#define IIR_TXRDY 0x2 /* Transmitter ready */
#define IIR_MLSC 0x0 /* Modem status */
#define IIR_NOPEND 0x1 /* No pending interrupts */
#define IIR_FIFO_MASK 0xc0 /* set if FIFOs are enabled */
/* fifo control register */
#define FIFO_ENABLE 0x01 /* Turn the FIFO on */
#define FIFO_RCV_RST 0x02 /* Reset RX FIFO */
#define FIFO_XMT_RST 0x04 /* Reset TX FIFO */
#define FIFO_DMA_MODE 0x08
#define FIFO_TRIGGER_1 0x00 /* Trigger RXRDY intr on 1 character */
#define FIFO_TRIGGER_4 0x40 /* ibid 4 */
#define FIFO_TRIGGER_8 0x80 /* ibid 8 */
#define FIFO_TRIGGER_14 0xc0 /* ibid 14 */
/* ST16650 fifo control register */
#define FIFO_RCV_TRIGGER_8 0x00
#define FIFO_RCV_TRIGGER_16 0x40
#define FIFO_RCV_TRIGGER_24 0x80
#define FIFO_RCV_TRIGGER_28 0xc0
#define FIFO_XMT_TRIGGER_16 0x00
#define FIFO_XMT_TRIGGER_8 0x10
#define FIFO_XMT_TRIGGER_24 0x20
#define FIFO_XMT_TRIGGER_30 0x30
/* XR16850 fifo control register */
#define FIFO_RCV3_TRIGGER_8 FIFO_RCV_TRIGGER_8
#define FIFO_RCV3_TRIGGER_16 FIFO_RCV_TRIGGER_16
#define FIFO_RCV3_TRIGGER_56 0x80
#define FIFO_RCV3_TRIGGER_60 0xc0
#define FIFO_XMT3_TRIGGER_8 0x00
#define FIFO_XMT3_TRIGGER_16 0x10
#define FIFO_XMT3_TRIGGER_32 0x20
#define FIFO_XMT3_TRIGGER_56 0x30
/* TI16750 fifo control register */
#define FIFO_ENABLE_64BYTE 0x20
/* line control register */
#define LCR_DLAB 0x80 /* Divisor latch access enable */
#define LCR_SBREAK 0x40 /* Break Control */
#define LCR_PZERO 0x38 /* Space parity */
#define LCR_PONE 0x28 /* Mark parity */
#define LCR_PEVEN 0x18 /* Even parity */
#define LCR_PODD 0x08 /* Odd parity */
#define LCR_PNONE 0x00 /* No parity */
#define LCR_PENAB 0x08 /* XXX - low order bit of all parity */
#define LCR_STOPB 0x04 /* 2 stop bits per serial word */
#define LCR_8BITS 0x03 /* 8 bits per serial word */
#define LCR_7BITS 0x02 /* 7 bits */
#define LCR_6BITS 0x01 /* 6 bits */
#define LCR_5BITS 0x00 /* 5 bits */
#define LCR_EFR 0xbf /* ST16650/XR16850 EFR access enable */
/* modem control register */
#define MCR_AFE 0x20 /* auto flow control */
#define MCR_LOOPBACK 0x10 /* Loop test: echos from TX to RX */
#define MCR_IENABLE 0x08 /* Out2: enables UART interrupts */
#define MCR_DRS 0x04 /* Out1: resets some internal modems */
#define MCR_RTS 0x02 /* Request To Send */
#define MCR_DTR 0x01 /* Data Terminal Ready */
/* line status register */
#define LSR_RCV_FIFO 0x80
#define LSR_TSRE 0x40 /* Transmitter empty: byte sent */
#define LSR_TXRDY 0x20 /* Transmitter buffer empty */
#define LSR_BI 0x10 /* Break detected */
#define LSR_FE 0x08 /* Framing error: bad stop bit */
#define LSR_PE 0x04 /* Parity error */
#define LSR_OE 0x02 /* Overrun, lost incoming byte */
#define LSR_RXRDY 0x01 /* Byte ready in Receive Buffer */
#define LSR_RCV_MASK 0x1f /* Mask for incoming data or error */
/* modem status register */
/* All deltas are from the last read of the MSR. */
#define MSR_DCD 0x80 /* Current Data Carrier Detect */
#define MSR_RI 0x40 /* Current Ring Indicator */
#define MSR_DSR 0x20 /* Current Data Set Ready */
#define MSR_CTS 0x10 /* Current Clear to Send */
#define MSR_DDCD 0x08 /* DCD has changed state */
#define MSR_TERI 0x04 /* RI has toggled low to high */
#define MSR_DDSR 0x02 /* DSR has changed state */
#define MSR_DCTS 0x01 /* CTS has changed state */
/* enhanced features register */
#define EFR_ECB 0x10 /* enhanced control bit */
#define EFR_SCD 0x20 /* special character detect */
#define EFR_RTS 0x40 /* RTS flow control */
#define EFR_CTS 0x80 /* CTS flow control */
/* enhanced FIFO control register */
#define FCTL_MODE 0x80
#define FCTL_SWAP 0x40
#define FCTL_RS485 0x08
#define FCTL_IrRxInv 0x04
#define FCTL_TRIGGER2 0x10
#define FCTL_TRIGGER3 0x20
/* infrared selection register */
#define ISR_XMITIR 0x01 /* transmitter SIR enable */
#define ISR_RCVEIR 0x02 /* receiver SIR enable */
#define ISR_XMODE 0x04 /* 1.6us transmit pulse width */
#define ISR_TXPL 0x08 /* negative transmit data polarity */
#define ISR_RXPL 0x10 /* negative receive data polarity */
#ifdef COM_PXA2X0
#define COM_NPORTS 9
#else
#define COM_NPORTS 8
#endif
/*
* WARNING: Serial console is assumed to be at COM1 address
* and CONUNIT must be 0.
*/
#ifndef CONADDR
#define CONADDR (0x3f8)
#else
#define CONADDR_OVERRIDE
#endif
#ifndef CONUNIT
#define CONUNIT (0)
#endif
|
