1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
|
Post-installation instructions for X.Org on OpenBSD/sparc64
-----------------------------------------------------------
Contents
--------
Single, unaccelerated display
Single, accelerated display
Dual, unaccelerated display
Single, unaccelerated display
-----------------------------
This setup is by far the easiest to configure and is supported on just
about every machine OpenBSD/sparc64 runs on (both PCI and SBus based
machines). These setup do not require any configuration file.
To use xdm from rc.conf, it is necessary to disable /dev/console in
/etc/ttys, change the 'status' of /dev/console to 'off'.
Single, accelerated display
---------------------------
Accelerated access to the framebuffer is supported on machines with
PCI VGA or UPA Creator framebuffers.
To use a PCI VGA framebuffer, retrieve the PCI bus, device and function
of the video card, eg:
blade$ dmesg | grep vgafb
vgafb0 at pci0 dev 19 function 0 "ATI Rage XL" rev 0x27
wsdisplay0 at vgafb0: console (std, sun emulation), using wskbd0
The framebuffer is on bus 0, device 19, function 0. Now, create
/etc/X11/xorg.conf, with the following content (replace 0:19:0 with the
bus:dev:func of the framebuffer):
Section "Device"
Identifier "Card0"
BusID "PCI:0:19:0"
Option "composite_sync" "True"
# Use the following option on Blade-100
# Option "reference_clock" "29.5MHz"
EndSection
Section "Monitor"
Identifier "Monitor0"
HorizSync 31.5-70
VertRefresh 50-90
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
EndSection
See xorg.conf(5) for more options. You may want to replace the frequency
ranges in the "Monitor" section with the actual ranges supported by
your monitor.
For UPA Creator framebuffers, the device will be automatically detected
and you don't need to have an xorg.conf file.
To use xdm from rc.conf, it is necessary to disable /dev/console in
/etc/ttys, change the 'status' of /dev/console to 'off'.
Dual, unaccelerated display
---------------------------
Dual-headed displays are only supported on machines with SBus framebuffers.
These configurations will require a configuration file.
Create /etc/X11/xorg.conf, with these two sections for each framebuffer:
Section "Device"
Identifier "Wsdisplay0"
Driver "wsfb"
Option "device" "/dev/ttyC0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Wsdisplay0"
EndSection
This example is for the first screen. For the others, increment the
"Wsdisplay" and "Screen" numbers, and change the device to /dev/ttyD0
for the second display, /dev/ttyE0 for the third, and so on.
Then, you'll need to create a ServerLayout section describing all the
displays and their location relative to the first, as in:
Section "ServerLayout"
Identifier "wsfb"
Screen 0 "Screen0"
Screen 1 "Screen1" RightOf "Screen0"
EndSection
See xorg.conf(5) for more options.
To use xdm from rc.conf, it is necessary to disable /dev/console in
/etc/ttys, change the 'status' of /dev/console to 'off'.
problem_blurb
$OpenBSD: README.sparc64,v 1.10 2011/02/21 18:13:18 miod Exp $
|
