Order flags alphabetically.

1 files changed, 80 insertions, 80 deletions

diff --git a/sbin/ifconfig/ifconfig.8 b/sbin/ifconfig/ifconfig.8
index da81ef2b304..ab016671500 100644
--- a/sbin/ifconfig/ifconfig.8
+++ b/sbin/ifconfig/ifconfig.8
@@ -1,4 +1,4 @@
-.\"	$OpenBSD: ifconfig.8,v 1.35 2000/01/15 19:47:01 angelos Exp $
+.\"	$OpenBSD: ifconfig.8,v 1.36 2000/01/15 20:11:14 angelos Exp $
 .\"	$NetBSD: ifconfig.8,v 1.11 1996/01/04 21:27:29 pk Exp $
 .\"     $FreeBSD: ifconfig.8,v 1.16 1998/02/01 07:03:29 steve Exp $
 .\"
@@ -145,71 +145,6 @@ for example,
 The following parameters may be set with
 .Nm ifconfig :
 .Bl -tag -width dest_addressxx
-.It Cm dstsa
-Bind an
-.Xr ipsec 4
-Security Association (SA) to an
-.Xr enc 4
-interface. The interface can then be used in conjunction with the
-.Xr bridge 4
-to establish virtual Local Area Networks (LANs). The SA is specified
-as
-.Ar address/SPI/protocol ,
-where
-.Ar address
-is an IPv4 or IPv6 address,
-.Ar SPI 
-is a hexadecimal number, and
-.Ar protocol
-is a decimal number identifying the security protocol (typically 50
-for ESP, 51 for AH, or 4 for IP-in-IP). The SA must exist for the
-operation to be successfully completed. Typically, such SAs would be
-established via
-.Xr ipsecadm 1 .
-This SA will be used to send packets to a remote host via
-.Xr ipsec 4 .
-If the
-.Ar 0.0.0.0/0/0
-or
-.Ar ::/0/0
-SA is specified, any existing binding between the corresponding
-.Xr enc 4
-interface and the SA is cleared (in fact, just the SPI and the protocol
-part of the SA have to be set to zero). Only one SA may be bound to an
-.Xr enc 4
-interface at a time. SAs may not be bound to the
-.Dq enc0
-interface.
-.It Cm srcsa
-Similar to
-.Cm dstsa ,
-this operation binds an
-.Xr ipsec 4
-SA to an
-.Xr enc 4
-interface. The SAs bound via this operation are receiving SAs. Any
-packets received over one of these SAs, will be made to appear as if
-it arrived by the corresponding
-.Xr enc 4
-interface. If the interface is part of a bridge, the packets will be
-delivered to the bridge. Contrary to the
-.Cm dstsa
-flag, multiple SAs may be bound to an
-.Xr enc 4
-interface via this operation. Similar to the
-.Cm dstsa
-flag, no SAs may be bound to the
-.Dq enc0
-interface.
-.It Cm clearsa
-Remove the binding between an SA and an
-.Xr enc 4
-interface, such as established with the
-.Cm srcsa
-or
-.Cm dstsa
-flags. If the all-zeroes SA is specified, the sending SA is cleared
-by default.
 .It Cm alias
 Establish an additional network address for this interface.
 This is sometimes useful when changing network numbers, and
@@ -236,6 +171,15 @@ Clear the IPv6 anycast address bit.
 Specify the address to use to represent broadcasts to the
 network.
 The default broadcast address is the address with a host part of all 1's.
+.It Cm clearsa
+Remove the binding between an SA and an
+.Xr enc 4
+interface, such as established with the
+.Cm srcsa
+or
+.Cm dstsa
+flags. If the all-zeroes SA is specified, the sending SA is cleared
+by default.
 .It Cm debug
 Enable driver dependent debugging code; usually, this turns on
 extra console error logging.
@@ -260,6 +204,41 @@ the system will not attempt to
 transmit messages through that interface.
 If possible, the interface will be reset to disable reception as well.
 This action does not automatically disable routes using the interface.
+.It Cm dstsa
+Bind an
+.Xr ipsec 4
+Security Association (SA) to an
+.Xr enc 4
+interface. The interface can then be used in conjunction with the
+.Xr bridge 4
+to establish virtual Local Area Networks (LANs). The SA is specified
+as
+.Ar address/SPI/protocol ,
+where
+.Ar address
+is an IPv4 or IPv6 address,
+.Ar SPI 
+is a hexadecimal number, and
+.Ar protocol
+is a decimal number identifying the security protocol (typically 50
+for ESP, 51 for AH, or 4 for IP-in-IP). The SA must exist for the
+operation to be successfully completed. Typically, such SAs would be
+established via
+.Xr ipsecadm 1 .
+This SA will be used to send packets to a remote host via
+.Xr ipsec 4 .
+If the
+.Ar 0.0.0.0/0/0
+or
+.Ar ::/0/0
+SA is specified, any existing binding between the corresponding
+.Xr enc 4
+interface and the SA is cleared (in fact, just the SPI and the protocol
+part of the SA have to be set to zero). Only one SA may be bound to an
+.Xr enc 4
+interface at a time. SAs may not be bound to the
+.Dq enc0
+interface.
 .It Cm ipdst
 This is used to specify an Internet host who is willing to receive
 ip packets encapsulating NS packets bound for a remote network.
@@ -269,6 +248,15 @@ of the destination.
 IP encapsulation of
 .Tn CLNP
 packets is done differently.
+.It Cm link[0-2]
+Enable special processing of the link level of the interface.
+These three options are interface specific in actual effect; however,
+they are in general used to select special modes of operation. An example
+of this is to enable SLIP compression, or to select the connector type
+for some Ethernet cards.  Refer to the man page for the specific driver
+for more information.
+.It Fl link[0-2]
+Disable special processing at the link level with the specified interface.
 .It Cm media Ar type
 Set the media type of the interface to
 .Ar type .
@@ -354,11 +342,6 @@ There is some evidence that a number different from 1 may be useful
 for
 .Tn AFI
 37 type addresses.
-.It Cm range
-Under AppleTalk, set the interface to respond to a
-.Em netrange
-of the form startnet-endnet. AppleTalk uses this scheme instead of
-netmasks though OpenBSD implements it internally as a set of netmasks.
 .It Cm phase
 The argument following this specifies the version (phase) of the
 AppleTalk network attached to the interface. Values of 1 or 2 are permitted.
@@ -370,6 +353,32 @@ Set preferred lifetime for the address.
 Effect is similar to
 .Cm netmask ,
 but you can specify by prefix length by digits.
+.It Cm range
+Under AppleTalk, set the interface to respond to a
+.Em netrange
+of the form startnet-endnet. AppleTalk uses this scheme instead of
+netmasks though OpenBSD implements it internally as a set of netmasks.
+.It Cm srcsa
+Similar to
+.Cm dstsa ,
+this operation binds an
+.Xr ipsec 4
+SA to an
+.Xr enc 4
+interface. The SAs bound via this operation are receiving SAs. Any
+packets received over one of these SAs, will be made to appear as if
+it arrived by the corresponding
+.Xr enc 4
+interface. If the interface is part of a bridge, the packets will be
+delivered to the bridge. Contrary to the
+.Cm dstsa
+flag, multiple SAs may be bound to an
+.Xr enc 4
+interface via this operation. Similar to the
+.Cm dstsa
+flag, no SAs may be bound to the
+.Dq enc0
+interface.
 .It Cm tentative
 (inet6 only)
 Set the IPv6 tentative address bit.
@@ -398,15 +407,6 @@ Currently used by Internet protocols only.
 Disable the use of a
 .Dq trailer
 link level encapsulation.
-.It Cm link[0-2]
-Enable special processing of the link level of the interface.
-These three options are interface specific in actual effect; however,
-they are in general used to select special modes of operation. An example
-of this is to enable SLIP compression, or to select the connector type
-for some Ethernet cards.  Refer to the man page for the specific driver
-for more information.
-.It Fl link[0-2]
-Disable special processing at the link level with the specified interface.
 .It Cm up
 Mark an interface
 .Dq up .