Factorize more common texts from the ramdisk operation.

No text changes except for harmonization, and the blurb about network
interface flags has bene slightly changed for some arches.

1 files changed, 10 insertions, 67 deletions

diff --git a/distrib/notes/sparc64/install b/distrib/notes/sparc64/install
index ad3c2c650bd..99ade14fee3 100644
--- a/distrib/notes/sparc64/install
+++ b/distrib/notes/sparc64/install
@@ -1,4 +1,4 @@
-dnl	$OpenBSD: install,v 1.20 2002/03/28 19:54:40 miod Exp $
+dnl	$OpenBSD: install,v 1.21 2002/03/30 22:52:58 miod Exp $
 OpenBSDInstallPrelude
 
 There are several ways to install OpenBSD onto a disk. The easiest way
@@ -129,9 +129,7 @@ OpenBSDBootMsgs
 	(If your terminal type is xterm, just use vt100).
 
 dnl put this back for 3.2
-dnl	After entering the terminal type you will be asked whether you
-dnl	wish to do an "(I)nstall" or an "(U)pgrade".  Enter 'I' for a
-dnl	fresh install or 'U' to upgrade an existing installation.
+dnl OpenBSDInstallpart3({:- or "wd0" for IDE drives-:})
 	After entering the terminal type you will be asked whether you
 	wish to do an "(I)nstall".  Enter 'I' for a fresh installation.
 	Note that you cannot upgrade a previous OpenBSD installation
@@ -143,70 +141,15 @@ dnl	fresh install or 'U' to upgrade an existing installation.
 	it can install on, and ask you which it should use.  The name
 	of the disk is typically "sd0" for SCSI drives and "wd0" for
 	IDE drives. Reply with the name of your disk.
+dnl end put this back
 
-	Next you will have to edit or create a disklabel for the disk
-	OpenBSD is being installed on.  The installation script will
-	invoke the text editor allowing you to do this.  Note that
-	partition 'c' inside this disk label should ALWAYS reflect the
-	entire disk, including any non-OpenBSD portions.  The root file
-	system should be in partition 'a', and swap is usually in partition
-	'b'.  It is recommended that you create separate partitions for
-	root and /usr, you may also want to specify /var and /home
-	partitions.
-
-	The swap partition (usually 'b') should have a type of "swap", all
-	other native OpenBSD partitions should have a type of "4.2BSD".
-	Block and fragment sizes are usually 8192 and 1024 bytes, but can
-	also be 16384 and 2048 bytes.
-
-	The install program will now label your disk and ask which file
-	systems should be created on which partitions.  It will auto-
-	matically select the 'a' partition to be the root file system.
-	Next it will ask for which disk and partition you want a file
-	system created on.  This will be the same as the disk name (e.g.
-	"sd0") with the letter identifying the partition (e.g. "d")
-	appended (e.g. "sd0d").  Then it will ask where this partition is
-	to be mounted, e.g. /usr.  This process will be repeated until
-	you type "done".
-
-	At this point you will be asked to confirm that the file system
-	information you have entered is correct, and given an opportunity
-	to change the file system table.  Next it will create the new file
-	systems as specified, OVERWRITING ANY EXISTING DATA.  This is the
-	point of no return.
-
-	After all your file systems have been created, the install program
-	will give you an opportunity to configure the network.  The network
-	configuration you enter (if any) can then be used to do the install
-	from another system using NFS, HTTP or FTP, and will also be the
-	configuration used by the system after the installation is complete.
-
-	If you select to configure the network, the install program will
-	ask you for a name of your system and the DNS domain name to use.
-	Note that the host name should be without the domain part, and that
-	the domain name should NOT {:-include-:} the host name part.
-
-	Next the system will give you a list of network interfaces you can
-	configure.  For each network interface you select to configure, it
-	will ask for the IP address to use, the symbolic host name to use,
-	the netmask to use and any media flags to set. It is usually safe
-	to keep the default settings.
-
-	After all network interfaces have been configured the install pro-
-	gram will ask for a default route and IP address of the primary
-	name server to use.  You will also be presented with an opportunity
-	to edit the host table.
-
-	At this point you will be allowed to edit the file system table
-	that will be used for the remainder of the installation and that
-	will be used by the finished system, following which the new file
-	systems will be mounted to complete the installation.
-
-	After these preparatory steps have been completed, you will be
-	able to extract the distribution sets onto your system.  There
-	are several install methods supported; FTP, HTTP, tape, CD-ROM, NFS
-	or a local disk partition.  Note that installation from floppies
-	is not currently supported.
+OpenBSDInstallPart4
+
+OpenBSDInstallPart5(sd0)
+
+OpenBSDInstallNet
+
+OpenBSDInstallNet2({:-CD-ROM, NFS, -:},nofloppy)
 
 OpenBSDFTPInstall