| Age | Commit message (Collapse) | Author |
|---|
|
ok mpi@
|
|
|
|
the specific queues are ic_mgtq, ic_pwrsaveq, and ni_savedq. rtw
had its own queue for beacons.
tested by mpi@ and jmc@
ok mpi@
|
|
traversal code to suspend/resume
ok oga kettenis blambert
|
|
them from the powerhook. Fix a few quibbles about the things done for
the IFF_RUNNING and IFF_UP cases
ok kettenis
|
|
This is needed for the addition of further suspend/resume actions.
Okay deraadt@, marco@.
|
|
|
|
ok jsg@
|
|
caused severe blood damage to laboratory animals. Not to mention swine flu.
|
|
pass a pointer to an ieee80211_rxinfo structure containing those two
fields plus an extra flags field that indicates whether the frame was
decrypted by hardware or not.
required for a future fix.
|
|
functions into the two drivers that use them (atw and rtw.)
this code is not generic enough to be used by other drivers and
there is no chance that it will ever be used in newer driver since
it supports 802.11b only.
plus, it hurts my eyes each time i look into ieee80211_output.c.
"fine with me as long as the logic doesn't change in the functions" jsg@
|
|
|
|
Miscellaneous Realtek RTL8180L driver improvements:
3 Revamp handling of transmit descriptor rings.
4 Reliably IFF_OACTIVE when transmit descriptors are available, to
stop the transmit section of the driver from freezing up.
5 Fix beacon transmission in adhoc and hostap modes. XXX There is
a wart in hostap mode, where beacons are transmitted at 1/2 the
correct rate. Load beacon descriptors when the RTW_INTR_BINT
interrupt arrives; schedule RTW_INTR_BINT 1ms ahead of the target
beacon time.
6 Recover more gracefully from tx/rx errors: avoid
transmitter/receiver/chip resets. Try to re-synchronize software
state with hardware state---e.g., load next descriptor pointer
from hardware.
7 Activate the transmit watchdog timer for beacons as well as other
packets.
8 Introduce rtw_idle() that waits for transmit DMA to finish; call
it before resetting the transmitter.
|
|
"looks fine" reyk@
|
|
why? rtw uses the smc93cx6 EEPROM and a separate diff will allow
accessing it without depending on the bus_space_* functions. this is
required for the RTL8187L.
discussed with jsg@
|
|
|
|
rtw_attach simplifying things in the process. ok reyk@
|
|
ok jsg@
|
|
|
|
which made things overly complicated.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
log message:
Program the LEDs based on operating state and packet activity.
* On a Revision F RTL8180, blink LED1 at 1Hz to indicate
scan/authenticate/associate states. In the run state, turn LED1
on. In every state, blink LED1 at 5Hz to indicate non-beacon
tx/rx activity. I would like to use two LEDs, but in all my
Rev. F instances, LED0 is not wired to an LED; instead, the
first LED is wired to indicate that the card's power is on.
* On a Revision D RTL8180, program the LEDs so that LED0 indicates
Tx, and LED1 indicates Rx. The Rx LED will blink annoyingly if
there are beacons in the air, but at least the Tx LED is useful.
* Store the hardware revision in the softc to support my futile
attempt at programming LEDs for both Rev. D and Rev. F parts;
I never did get Rev. D LEDs to work right.
* Add a debug flag RTW_DEBUG_LED for the LED transitions.
|
|
From part of rtw.c rev 1.42:
log message:
Add RTW_TPPOLL_ALL, RTW_TPPOLL_SALL to start and stop, respectively,
all of the transmit rings.
Revamp the transmit section to make better use of all the transmit
rings: beacon queue, high-, low-, and medium-priority rings. Put
beacon frames on the beacon ring. All other management frames,
and data frames, go on the medium-priority ring. Power-save data
frames go on the high-priority ring. (Note that powersaving is
not implemented!) This is a work in progress.
Send all 802.11 Management frames at 1Mbps.
After we put a packet on a transmit ring, tickle the right bit in
the TPPOLL to tell RTL8180. Stop all rings on error and in rtw_stop.
And rtw.c rev 1.33:
log message:
Consolidate variables related to the rx ring in sc_rxdesc_blk,
which is a struct rtw_rxdesc_blk.
Put a copy of the DMA tag and the DMA map into the rx- and tx-ring
blocks so that I don't have to pass them to subroutines all of the
time.
ok dlg@
|
|
From part of rtw.c rev 1.42:
Move the register access mode into struct rtw_regs. Change
rtw_set_access, rtw_set_access1 to match.
|
|
From rtw.c rev 1.34:
I like the tlp/atw-style names for software descriptors, txsoft,
better than txctl. Change from rtw_txctl/rtw_rxctl to
rtw_txsoft/rtw_rxsoft. Change the descriptor blocks' names to
match: rtw_txctl_blk becomes rtw_txsoft_blk. Change the member-name
prefixes for both software and hardware descriptors.
|
|
|
|
whether to use host or MAC controlled RF I/O.
From part of NetBSD rev 1.42
|
|
Not yet working.
|
