| Age | Commit message (Expand) | Author |
|---|
| 2013-01-06 | acknowlege -> acknowledge | Martynas Venckus |
| 2012-12-31 | Spell `calculation' correctly. | Miod Vallat |
| 2012-12-07 | Remove support for waiting for an interrupt within hostcmd_send(), since only | Stefan Sperling |
| 2012-12-05 | Remove excessive sys/cdefs.h inclusion | Theo de Raadt |
| 2012-12-01 | Add RX TCP/UDP checksum offload support. | Brad Smith |
| 2012-11-29 | Add rtsx(4), a new driver for the Realtek RTS5209 card reader. | Stefan Sperling |
| 2012-11-29 | Remove setting an initial assumed baudrate upon driver attach which is not | Brad Smith |
| 2012-10-27 | Implememnt AP side power saving for acx(4). Tested on acx11. | Claudio Jeker |
| 2012-10-22 | Add flow control support. | Brad Smith |
| 2012-10-20 | Init values for the AR9485 were for version 1.0 of this chip, which according | Stefan Sperling |
| 2012-10-20 | Fix hardware kill switch detection for the ar9300 chip family. The driver was | Stefan Sperling |
| 2012-10-19 | Simplify xl_iff_90x() a bit and only check ac->ac_multicnt since ac_multicnt | Brad Smith |
| 2012-10-17 | Narrow the spltty/splx pair in com_activate to only enclose the minimum | Theo de Raadt |
| 2012-10-17 | cleanup more of the driver soft-state when suspending; in certain | Theo de Raadt |
| 2012-10-17 | AH_BYTE_ORDER and AH_BIG_ENDIAN are holdovers from the old FreeBSD | Jonathan Gray |
| 2012-10-13 | Move WOL activation to DVACT_POWERDOWN (instead of doing it twice, at | Theo de Raadt |
| 2012-10-12 | Cleanup false positives for uninitialized uses. | Christiano F. Haesbaert |
| 2012-10-11 | Enable Host AP power saving support for the RT2700, RT2800 and RT3090 chipsets. | Mark Kettenis |
| 2012-10-10 | Avoid potential uninitialized variable access in fxp driver. | Bret Lambert |
| 2012-10-04 | Clean up uninitialized warnings from ar9003. | Christiano F. Haesbaert |
| 2012-09-18 | several tweaks to make mpi(4) work for vmware emulated sas adapters. | David Gwynne |
| 2012-09-12 | Use sg_addr instead of sg_lo_addr, leftovers from last commit. | Christiano F. Haesbaert |
| 2012-09-12 | Make sure we don't sleep on autoconf. | Christiano F. Haesbaert |
| 2012-09-04 | The powerlevel is an unsigned int, there is no need to check for negative | Claudio Jeker |
| 2012-08-30 | make a variable that can take a value of -1 signed to match what the | Jonathan Gray |
| 2012-08-26 | htole64 works as good as htole32 twice for dma virtual addresses. | David Gwynne |
| 2012-08-25 | Better detection of the st16650 v1 (with the broken fifo). Gets rid of | Mark Kettenis |
| 2012-08-25 | Turns out the v445 isn't happy at all if we touch the registers that deal | Mark Kettenis |
| 2012-08-25 | Add support for power saving in Host AP mode. | Mark Kettenis |
| 2012-08-23 | Fix a race in rt2661 Tx interrupt processing which can cause Tx processing | Stefan Sperling |
| 2012-08-19 | Skip putting a port in sleep mode when it is used as serial console. In that | Mark Kettenis |
| 2012-08-17 | add support for "physical devices" on skinny controllers. | David Gwynne |
| 2012-08-16 | fix mfi_poll by having it do delays between loops, and breaking on | David Gwynne |
| 2012-08-16 | rework mfi_poll so it will do all the completions on a ccb including | David Gwynne |
| 2012-08-16 | stop passing mfi_softc around as a member of the ccb, consistently give it | David Gwynne |
| 2012-08-16 | scrub ccbs when we're about to use them, not when we put them back | David Gwynne |
| 2012-08-16 | move the dma syncs for the ccb data into ccb_done, so we can do it once | David Gwynne |
| 2012-08-16 | fix up the dma sync for the command frame in mfi_done. | David Gwynne |
| 2012-08-15 | Remove the old ioctl interface which has been disabled for over | Jonathan Gray |
| 2012-08-14 | use scsi_get_link to find out the name of a child device for bioctl rather | David Gwynne |
| 2012-08-14 | expose the max number of logical volumes the hardware supports as the width | David Gwynne |
| 2012-08-14 | print the boards name (eg, perc 5/i) according to the firmware like mfii. | David Gwynne |
| 2012-08-14 | gc sc_flags now that the iop struct can tell us where the different IDBs | David Gwynne |
| 2012-08-14 | oops, dont claim FUSION is an iop type we will support in mfi(4) | David Gwynne |
| 2012-08-14 | move knowledge of the location of the inbound doorbell out of code in | David Gwynne |
| 2012-08-13 | get rid of the last foo_lo and foo_hi bits i could find in the hardware | David Gwynne |
| 2012-08-13 | do appropriate bus_dmamapy_syncs around the pcq/completion ring. | David Gwynne |
| 2012-08-13 | replace uint32_ts for hi and lo addresses in the mfi_init_ hardware | David Gwynne |
| 2012-08-11 | the producer/consumer values are used by the device, which is little | David Gwynne |
| 2012-08-10 | simplify pckbc_xt_translation() | Alexandr Shadchin |
