1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
|
Installation is supported from several media types, including:
* Tape
* NFS
* CD-ROM
* FTP
Note that installing on a "bare" machine requires some bootable
device; either a tape drive or Sun-compatible NFS server.
The procedure for transferring the distribution sets onto
installation media depends on the type of media. Instructions
for each type of media are given below.
In order to create installation media, you will need all the
files in these two directories:
.../OpenBSD-1.1/sun3/install
.../OpenBSD-1-1/sun3/binary
* Creating boot/install tapes:
Installing from tape is the simplest method of all.
This method uses two tapes; one called the "boot"
tape, and another called the "install" tape.
The boot tape is created as follows:
cd .../OpenBSD-1.1/sun3/install
set T = /dev/nrst0
mt -f $T rewind
dd if=tapeboot of=$T bs=8k conv=sync
dd if=bsd-rd of=$T bs=8k conv=sync
gzip -d < miniroot.gz | dd of=$T bs=8k
mt -f $T rewind
The install tape is created as follows:
cd .../OpenBSD-1.1/sun3/install
set T = /dev/nrst0
mt -f $T rewind
foreach f (base etc comp games man misc text)
gzip -d < $f.gz | dd of=$T bs=8k
end
mt -f $T rewind
If the tapes do not work as expected, you may need to explicitly
set the EOF mark at the end of each tape segment. It may also be
necessary to use the `conv=osync' argument to dd(1). Note that
this argument is incompatible with the `bs=' argument. Consult
the tape-related manual pages on the system where the tapes are
created for more details.
* Boot/Install from NFS server:
If your machine has a disk and network connection, but no tape drive,
it may be convenient for you to install OpenBSD over the network. This
involves temporarily booting your machine over NFS, just long enough
so you can initialize its disk. This method requires that you have
access to an NFS server on your network so you can configure it to
support diskless boot for your machine. Configuring the NFS server
is normally a task for a system administrator, and is not trivial.
If you are using a OpenBSD system as the boot-server, have a look at
the diskless(8) manual page for guidelines on how to proceed with
this. If the server runs another operating system, consult the
documentation that came with it (i.e. add_client(8) on SunOS).
Your Sun3 expects to be able to download a second stage bootstrap
program via TFTP after having acquired its IP address through RARP
when instructed to boot "over the net". It will look for a filename
derived from the machine's IP address expressed in hexadecimal. For
example, a sun3 which has been assigned IP address 130.115.144.11
will make an TFTP request for `8273900B'. Normally, this file is a
symbolic link to the OpenBSD/sun3 "netboot" program, which should be
located in a place where the TFTP daemon can find it (remember, many
TFTP daemons run in a chroot'ed environment). The netboot program
may be found in the install directory of this distribution.
The netboot program will query a bootparamd server to find the
NFS server address and path name for its root, and then load a
kernel from that location. The server should have a copy of the
bsd-rd kernel in the root area for your client (no other files
are needed in the client root) and /etc/bootparams on the server
should have an entry for your client and its root directory.
The client will need access to the miniroot image, which can be
provided using NFS or remote shell. If using NFS, miniroot.gz
must be expanded on the server, because there is no gzip program
in the RAMDISK image. The unzipped miniroot takes 8MB of space.
If you will be installing OpenBSD on several clients, it may be useful
to know that you can use a single NFS root for all the clients as long
as they only use the bsd-rd kernel. There will be no conflict
between clients because the RAM-disk kernel will not use the NFS root.
No swap file is needed; the RAM-disk kernel does not use that either.
* Install/Upgrade from CD-ROM:
This method requires that you boot from another device (i.e. tape
or network, as described above). You may need to make a boot tape
on another machine using the files provided on the CD-ROM. Once
you have booted bsd-rd (the RAM-disk kernel) and loaded the
miniroot, you can load any of the distribution sets directly from
the CD-ROM. The "install" program in the miniroot automates the
work required to mount the CD-ROM and extract the files.
* Install/Upgrade via FTP:
This method requires that you boot from another device (i.e. tape
or network, as described above). You may need to make a boot tape
on another machine using the files in .../install (which you get
via FTP). Once you have booted bsd-rd (the RAM-disk kernel)
and loaded the miniroot, you can load any of the distribution sets
over the net using FTP. The "install" program in the miniroot
automates the work required to configure the network interface and
transfer the files.
This method, of course, requires network access to an FTP server.
This might be a local system, or it might even be ftp.OpenBSD.ORG
itself. If you wish to use ftp.OpenBSD.ORG as your FTP file
server, you may want to keep the following information handy:
IP Address: 128.6.190.2
Login: anonymous
Password: <your e-mail address>
Server path: /pub/OpenBSD/OpenBSD-1.1/sun3/binary
|
