blob: 1e9f67d69eb941c0a2c670efa2c7f59bf6c933b9 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
|
# $OpenBSD: RAMDISK,v 1.8 2001/10/10 04:24:12 deraadt Exp $
# Machine architecture; required by config(8)
machine sparc64
option SUN4U
option _LP64
# maxusers means mostly "let's get small" in terms of kernel malloc's
maxusers 2
option RAMDISK_HOOKS
option MINIROOTSIZE=6144
#option DDB # need this to see what's happening
option TIMEZONE=0 # time zone to adjust RTC time by
option DST=0 # daylight saving time used by RTC
option SMALL_KERNEL
option DIAGNOSTIC # internal consistency checks
option FFS # UFS
option NFSCLIENT # Network File System client
option CD9660 # ISO 9660 + Rock Ridge file system
option INET # IP + ICMP + TCP + UDP
option BOOT_CONFIG # add support for boot -c
# Generic swap; second partition of root disk or network.
config bsd root on rd0a
# Main bus and CPU .. all systems.
mainbus0 at root
cpu0 at mainbus0
# Bus types found on SPARC systems.
sbus0 at mainbus0 # Ultra 1
psycho* at mainbus0
pci* at psycho? # Ultra 5
pci* at ppb?
ppb* at pci? dev ? function ?
ebus* at pci?
hme* at pci? dev ? function ?
gem* at pci? dev ? function ?
auxio* at ebus?
com* at ebus?
clock* at sbus? slot ? offset ? # Mostek clock
clock* at ebus?
timer* at mainbus0 # Timer chip
## PROM console driver -- if all else fails
pcons0 at mainbus0 # PROM console
## Lance Ethernet - AMD7990
le* at sbus? slot ? offset ?
ledma* at sbus? slot ? offset ?
le* at ledma?
# Quad-ethernet glue device, and sub-devices
qec* at sbus? slot ? offset ?
qe* at qec?
be* at qec?
hme* at sbus? slot ? offset ?
pciide* at pci? dev ? function ? flags 0x0000
wd* at pciide? channel ? drive ? flags 0x0000
atapiscsi* at pciide? channel ?
scsibus* at atapiscsi?
#
# Note the flags on the esp entries below, that work around
# deficiencies in the current driver:
# bits 0-7: disable disconnect/reselect for the corresponding target
# bits 8-15: disable synch negotiation for target [bit-8]
# Note: targets 4-7 have disconnect/reselect enabled on the premise
# that tape devices normally have one of these targets. Tape
# devices should be allowed to disconnect for the SCSI bus
# to operate acceptably.
#
dma* at sbus? slot ? offset ? # SBus
esp* at dma? flags 0x0000 # SBus
esp* at sbus? slot ? offset ?
scsibus* at esp?
siop* at pci? dev ? function ?
scsibus* at siop?
# These entries find devices on all SCSI busses and assign
# unit numers dynamically.
sd* at scsibus? target ? lun ? # SCSI disks
cd* at scsibus? target ? lun ? # SCSI CD-ROMs
# Media Independent Interface (mii) drivers)
nsphy* at mii? phy ? # NS and compatible PHYs
qsphy* at mii? phy ? # Quality Semi QS6612 PHYs
ukphy* at mii? phy ? # Unknown PHYs
pseudo-device rd 2 # ramdisk
pseudo-device loop 1 # network loopback
pseudo-device bpfilter 1 # packet filter
|
