path: root/sys/dev/ic/ispvar.h

/*	$OpenBSD: ispvar.h,v 1.19 2001/12/14 00:20:55 mjacob Exp $ */
/*
 * Soft Definitions for for Qlogic ISP SCSI adapters.
 *
 * Copyright (c) 1997, 1998, 1999, 2000 by Matthew Jacob
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice immediately at the beginning of the file, without modification,
 *    this list of conditions, and the following disclaimer.
 * 2. The name of the author may not be used to endorse or promote products
 *    derived from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
 * SUCH DAMAGE.
 *
 */

#ifndef	_ISPVAR_H
#define	_ISPVAR_H

#if defined(__NetBSD__) || defined(__OpenBSD__)
#include <dev/ic/ispmbox.h>
#ifdef	ISP_TARGET_MODE
#include <dev/ic/isp_target.h>
#include <dev/ic/isp_tpublic.h>
#endif
#endif
#ifdef	__FreeBSD__
#include <dev/isp/ispmbox.h>
#ifdef	ISP_TARGET_MODE
#include <dev/isp/isp_target.h>
#include <dev/isp/isp_tpublic.h>
#endif
#endif
#ifdef	__linux__
#include "ispmbox.h"
#ifdef	ISP_TARGET_MODE
#include "isp_target.h"
#include "isp_tpublic.h"
#endif
#endif

#define	ISP_CORE_VERSION_MAJOR	2
#define	ISP_CORE_VERSION_MINOR	5

/*
 * Vector for bus specific code to provide specific services.
 */
struct ispsoftc;
struct ispmdvec {
	int		(*dv_rd_isr)
	    (struct ispsoftc *, u_int16_t *, u_int16_t *, u_int16_t *);
	u_int16_t	(*dv_rd_reg) (struct ispsoftc *, int);
	void		(*dv_wr_reg) (struct ispsoftc *, int, u_int16_t);
	int		(*dv_mbxdma) (struct ispsoftc *);
	int		(*dv_dmaset) (struct ispsoftc *,
	    XS_T *, ispreq_t *, u_int16_t *, u_int16_t);
	void		(*dv_dmaclr)
	    (struct ispsoftc *, XS_T *, u_int16_t);
	void		(*dv_reset0) (struct ispsoftc *);
	void		(*dv_reset1) (struct ispsoftc *);
	void		(*dv_dregs) (struct ispsoftc *, const char *);
	const u_int16_t	*dv_ispfw;	/* ptr to f/w */
	u_int16_t	dv_conf1;
	u_int16_t	dv_clock;	/* clock frequency */
};

/*
 * Overall parameters
 */
#define	MAX_TARGETS		16
#define	MAX_FC_TARG		256
#define	ISP_MAX_TARGETS(isp)	(IS_FC(isp)? MAX_FC_TARG : MAX_TARGETS)
#define	ISP_MAX_LUNS(isp)	(isp)->isp_maxluns

/*
 * 'Types'
 */
#ifndef	ISP_DMA_ADDR_T
#define	ISP_DMA_ADDR_T	u_int32_t
#endif

/*
 * Macros to access ISP registers through bus specific layers-
 * mostly wrappers to vector through the mdvec structure.
 */
#define	ISP_READ_ISR(isp, isrp, semap, mbox0p)	\
	(*(isp)->isp_mdvec->dv_rd_isr)(isp, isrp, semap, mbox0p)

#define	ISP_READ(isp, reg)	\
	(*(isp)->isp_mdvec->dv_rd_reg)((isp), (reg))

#define	ISP_WRITE(isp, reg, val)	\
	(*(isp)->isp_mdvec->dv_wr_reg)((isp), (reg), (val))

#define	ISP_MBOXDMASETUP(isp)	\
	(*(isp)->isp_mdvec->dv_mbxdma)((isp))

#define	ISP_DMASETUP(isp, xs, req, iptrp, optr)	\
	(*(isp)->isp_mdvec->dv_dmaset)((isp), (xs), (req), (iptrp), (optr))

#define	ISP_DMAFREE(isp, xs, hndl)	\
	if ((isp)->isp_mdvec->dv_dmaclr) \
	    (*(isp)->isp_mdvec->dv_dmaclr)((isp), (xs), (hndl))

#define	ISP_RESET0(isp)	\
	if ((isp)->isp_mdvec->dv_reset0) (*(isp)->isp_mdvec->dv_reset0)((isp))
#define	ISP_RESET1(isp)	\
	if ((isp)->isp_mdvec->dv_reset1) (*(isp)->isp_mdvec->dv_reset1)((isp))
#define	ISP_DUMPREGS(isp, m)	\
	if ((isp)->isp_mdvec->dv_dregs) (*(isp)->isp_mdvec->dv_dregs)((isp),(m))

#define	ISP_SETBITS(isp, reg, val)	\
 (*(isp)->isp_mdvec->dv_wr_reg)((isp), (reg), ISP_READ((isp), (reg)) | (val))

#define	ISP_CLRBITS(isp, reg, val)	\
 (*(isp)->isp_mdvec->dv_wr_reg)((isp), (reg), ISP_READ((isp), (reg)) & ~(val))

/*
 * The MEMORYBARRIER macro is defined per platform (to provide synchronization
 * on Request and Response Queues, Scratch DMA areas, and Registers)
 *
 * Defined Memory Barrier Synchronization Types
 */
#define	SYNC_REQUEST	0	/* request queue synchronization */
#define	SYNC_RESULT	1	/* result queue synchronization */
#define	SYNC_SFORDEV	2	/* scratch, sync for ISP */
#define	SYNC_SFORCPU	3	/* scratch, sync for CPU */
#define	SYNC_REG	4	/* for registers */

/*
 * Request/Response Queue defines and macros.
 * The maximum is defined per platform (and can be based on board type).
 */
/* This is the size of a queue entry (request and response) */
#define	QENTRY_LEN			64
/* Both request and result queue length must be a power of two */
#define	RQUEST_QUEUE_LEN(x)		MAXISPREQUEST(x)
#define	RESULT_QUEUE_LEN(x)		\
	(((MAXISPREQUEST(x) >> 2) < 64)? 64 : MAXISPREQUEST(x) >> 2)
#define	ISP_QUEUE_ENTRY(q, idx)		((q) + ((idx) * QENTRY_LEN))
#define	ISP_QUEUE_SIZE(n)		((n) * QENTRY_LEN)
#define	ISP_NXT_QENTRY(idx, qlen)	(((idx) + 1) & ((qlen)-1))
#define	ISP_QFREE(in, out, qlen)	\
	((in == out)? (qlen - 1) : ((in > out)? \
	((qlen - 1) - (in - out)) : (out - in - 1)))
#define	ISP_QAVAIL(isp)	\
	ISP_QFREE(isp->isp_reqidx, isp->isp_reqodx, RQUEST_QUEUE_LEN(isp))

#define	ISP_ADD_REQUEST(isp, nxti)					\
	MEMORYBARRIER(isp, SYNC_REQUEST, isp->isp_reqidx, QENTRY_LEN);	\
	WRITE_REQUEST_QUEUE_IN_POINTER(isp, nxti);			\
	isp->isp_reqidx = nxti

/*
 * SCSI Specific Host Adapter Parameters- per bus, per target
 */

typedef struct {
	u_int		isp_gotdparms		: 1,
			isp_req_ack_active_neg	: 1,
			isp_data_line_active_neg: 1,
			isp_cmd_dma_burst_enable: 1,
			isp_data_dma_burst_enabl: 1,
			isp_fifo_threshold	: 3,
			isp_ultramode		: 1,
			isp_diffmode		: 1,
			isp_lvdmode		: 1,
			isp_fast_mttr		: 1,	/* fast sram */
			isp_initiator_id	: 4,
			isp_async_data_setup	: 4;
	u_int16_t	isp_selection_timeout;
	u_int16_t	isp_max_queue_depth;
	u_int8_t	isp_tag_aging;
	u_int8_t	isp_bus_reset_delay;
	u_int8_t	isp_retry_count;
	u_int8_t	isp_retry_delay;
	struct {
		u_int32_t	
			exc_throttle	:	8,
					:	1,
			dev_enable	:	1,	/* ignored */
			dev_update	:	1,
			dev_refresh	:	1,
			actv_offset	:	4,
			goal_offset	:	4,
			nvrm_offset	:	4;
		u_int8_t	actv_period;	/* current sync period */
		u_int8_t	goal_period;	/* goal sync period */
		u_int8_t	nvrm_period;	/* nvram sync period */
		u_int16_t	actv_flags;	/* current device flags */
		u_int16_t	goal_flags;	/* goal device flags */
		u_int16_t	nvrm_flags;	/* nvram device flags */
	} isp_devparam[MAX_TARGETS];
} sdparam;

/*
 * Device Flags
 */
#define	DPARM_DISC	0x8000
#define	DPARM_PARITY	0x4000
#define	DPARM_WIDE	0x2000
#define	DPARM_SYNC	0x1000
#define	DPARM_TQING	0x0800
#define	DPARM_ARQ	0x0400
#define	DPARM_QFRZ	0x0200
#define	DPARM_RENEG	0x0100
#define	DPARM_NARROW	0x0080
#define	DPARM_ASYNC	0x0040
#define	DPARM_PPR	0x0020
#define	DPARM_DEFAULT	(0xFF00 & ~DPARM_QFRZ)
#define	DPARM_SAFE_DFLT	(DPARM_DEFAULT & ~(DPARM_WIDE|DPARM_SYNC|DPARM_TQING))


/* technically, not really correct, as they need to be rated based upon clock */
#define	ISP_80M_SYNCPARMS	0x0c09
#define	ISP_40M_SYNCPARMS	0x0c0a
#define	ISP_20M_SYNCPARMS	0x0c0c
#define	ISP_20M_SYNCPARMS_1040	0x080c
#define	ISP_10M_SYNCPARMS	0x0c19
#define	ISP_08M_SYNCPARMS	0x0c25
#define	ISP_05M_SYNCPARMS	0x0c32
#define	ISP_04M_SYNCPARMS	0x0c41

/*
 * Fibre Channel Specifics
 */
#define	FL_PORT_ID		0x7e	/* FL_Port Special ID */
#define	FC_PORT_ID		0x7f	/* Fabric Controller Special ID */
#define	FC_SNS_ID		0x80	/* SNS Server Special ID */

typedef struct {
	u_int32_t		isp_fwoptions	: 16,
				isp_gbspeed	: 2,
				isp_iid_set	: 1,
				loop_seen_once	: 1,
				isp_loopstate	: 4,	/* Current Loop State */
				isp_fwstate	: 3,	/* ISP F/W state */
				isp_gotdparms	: 1,
				isp_topo	: 3,
				isp_onfabric	: 1;
	u_int8_t		isp_iid;	/* 'initiator' id */
	u_int8_t		isp_loopid;	/* hard loop id */
	u_int8_t		isp_alpa;	/* ALPA */
	u_int32_t		isp_portid;
	volatile u_int16_t	isp_lipseq;	/* LIP sequence # */
	u_int16_t		isp_fwattr;	/* firmware attributes */
	u_int8_t		isp_execthrottle;
	u_int8_t		isp_retry_delay;
	u_int8_t		isp_retry_count;
	u_int8_t		isp_reserved;
	u_int16_t		isp_maxalloc;
	u_int16_t		isp_maxfrmlen;
	u_int64_t		isp_nodewwn;
	u_int64_t		isp_portwwn;
	/*
	 * Port Data Base. This is indexed by 'target', which is invariate.
	 * However, elements within can move around due to loop changes,
	 * so the actual loop ID passed to the F/W is in this structure.
	 * The first time the loop is seen up, loopid will match the index
	 * (except for fabric nodes which are above mapped above FC_SNS_ID
	 * and are completely virtual), but subsequent LIPs can cause things
	 * to move around.
	 */
	struct lportdb {
		u_int
					loopid		: 8,
							: 1,
					force_logout	: 1,
					was_fabric_dev	: 1,
					fabric_dev	: 1,
					loggedin	: 1,
					roles		: 2,
					valid		: 1;
		u_int32_t		portid;
		u_int64_t		node_wwn;
		u_int64_t		port_wwn;
	} portdb[MAX_FC_TARG], tport[FC_PORT_ID];

	/*
	 * Scratch DMA mapped in area to fetch Port Database stuff, etc.
	 */
	caddr_t			isp_scratch;
	ISP_DMA_ADDR_T		isp_scdma;
} fcparam;

#define	FW_CONFIG_WAIT		0
#define	FW_WAIT_AL_PA		1
#define	FW_WAIT_LOGIN		2
#define	FW_READY		3
#define	FW_LOSS_OF_SYNC		4
#define	FW_ERROR		5
#define	FW_REINIT		6
#define	FW_NON_PART		7

#define	LOOP_NIL		0
#define	LOOP_LIP_RCVD		1
#define	LOOP_PDB_RCVD		2
#define	LOOP_SCANNING_FABRIC	3
#define	LOOP_FSCAN_DONE		4
#define	LOOP_SCANNING_LOOP	5
#define	LOOP_LSCAN_DONE		6
#define	LOOP_SYNCING_PDB	7
#define	LOOP_READY		8

#define	TOPO_NL_PORT		0
#define	TOPO_FL_PORT		1
#define	TOPO_N_PORT		2
#define	TOPO_F_PORT		3
#define	TOPO_PTP_STUB		4

/*
 * Soft Structure per host adapter
 */
typedef struct ispsoftc {
	/*
	 * Platform (OS) specific data
	 */
	struct isposinfo	isp_osinfo;

	/*
	 * Pointer to bus specific functions and data
	 */
	struct ispmdvec *	isp_mdvec;

	/*
	 * (Mostly) nonvolatile state. Board specific parameters
	 * may contain some volatile state (e.g., current loop state).
	 */

	void * 			isp_param;	/* type specific */
	u_int16_t		isp_fwrev[3];	/* Loaded F/W revision */
	u_int16_t		isp_romfw_rev[3]; /* PROM F/W revision */
	u_int16_t		isp_maxcmds;	/* max possible I/O cmds */
	u_int8_t		isp_type;	/* HBA Chip Type */
	u_int8_t		isp_revision;	/* HBA Chip H/W Revision */
	u_int32_t		isp_maxluns;	/* maximum luns supported */

	u_int32_t		isp_clock	: 8,	/* input clock */
						: 5,
				isp_failed	: 1,	/* board failed */
				isp_open	: 1,	/* opened (ioctl) */
				isp_touched	: 1,	/* board ever seen? */
				isp_bustype	: 1,	/* SBus or PCI */
				isp_loaded_fw	: 1,	/* loaded firmware */
				isp_role	: 2,	/* roles supported */
				isp_dblev	: 12;	/* debug log mask */

	u_int32_t		isp_confopts;		/* config options */

	u_int16_t		isp_rqstinrp;	/* register for REQINP */
	u_int16_t		isp_rqstoutrp;	/* register for REQOUTP */
	u_int16_t		isp_respinrp;	/* register for RESINP */
	u_int16_t		isp_respoutrp;	/* register for RESOUTP */

	/*
	 * Instrumentation
	 */
	u_int64_t		isp_intcnt;		/* total int count */
	u_int64_t		isp_intbogus;		/* spurious int count */

	/*
	 * Volatile state
	 */

	volatile u_int32_t
		isp_obits	:	8,	/* mailbox command output */
		isp_mboxbsy	:	1,	/* mailbox command active */
		isp_state	:	3,
		isp_sendmarker	:	2,	/* send a marker entry */
		isp_update	:	2,	/* update parameters */
		isp_nactive	:	16;	/* how many commands active */
	volatile u_int16_t	isp_reqodx;	/* index of last ISP pickup */
	volatile u_int16_t	isp_reqidx;	/* index of next request */
	volatile u_int16_t	isp_residx;	/* index of next result */
	volatile u_int16_t	isp_lasthdls;	/* last handle seed */
	volatile u_int16_t	isp_mboxtmp[MAX_MAILBOX];
	volatile u_int16_t	isp_lastmbxcmd;	/* last mbox command sent */

	/*
	 * Active commands are stored here, indexed by handle functions.
	 */
	XS_T **isp_xflist;

	/*
	 * request/result queue pointers and dma handles for them.
	 */
	caddr_t			isp_rquest;
	caddr_t			isp_result;
	ISP_DMA_ADDR_T		isp_rquest_dma;
	ISP_DMA_ADDR_T		isp_result_dma;
} ispsoftc_t;

#define	SDPARAM(isp)	((sdparam *) (isp)->isp_param)
#define	FCPARAM(isp)	((fcparam *) (isp)->isp_param)

/*
 * ISP Driver Run States
 */
#define	ISP_NILSTATE	0
#define	ISP_RESETSTATE	1
#define	ISP_INITSTATE	2
#define	ISP_RUNSTATE	3

/*
 * ISP Configuration Options
 */
#define	ISP_CFG_NORELOAD	0x80	/* don't download f/w */
#define	ISP_CFG_NONVRAM		0x40	/* ignore NVRAM */
#define	ISP_CFG_TWOGB		0x20	/* force 2GB connection (23XX only) */
#define	ISP_CFG_ONEGB		0x10	/* force 1GB connection (23XX only) */
#define	ISP_CFG_FULL_DUPLEX	0x01	/* Full Duplex (Fibre Channel only) */
#define	ISP_CFG_OWNWWN		0x02	/* override NVRAM wwn */
#define	ISP_CFG_PORT_PREF	0x0C	/* Mask for Port Prefs (2200 only) */
#define	ISP_CFG_LPORT		0x00	/* prefer {N/F}L-Port connection */
#define	ISP_CFG_NPORT		0x04	/* prefer {N/F}-Port connection */
#define	ISP_CFG_NPORT_ONLY	0x08	/* insist on {N/F}-Port connection */
#define	ISP_CFG_LPORT_ONLY	0x0C	/* insist on {N/F}L-Port connection */

/*
 * Prior to calling isp_reset for the first time, the outer layer
 * should set isp_role to one of NONE, INITIATOR, TARGET, BOTH.
 *
 * If you set ISP_ROLE_NONE, the cards will be reset, new firmware loaded,
 * NVRAM read, and defaults set, but any further initialization (e.g.
 * INITIALIZE CONTROL BLOCK commands for 2X00 cards) won't be done.
 *
 * If INITIATOR MODE isn't set, attempts to run commands will be stopped
 * at isp_start and completed with the moral equivalent of SELECTION TIMEOUT.
 *
 * If TARGET MODE is set, it doesn't mean that the rest of target mode support
 * needs to be enabled, or will even work. What happens with the 2X00 cards
 * here is that if you have enabled it with TARGET MODE as part of the ICB
 * options, but you haven't given the f/w any ram resources for ATIOs or
 * Immediate Notifies, the f/w just handles what it can and you never see
 * anything. Basically, it sends a single byte of data (the first byte,
 * which you can set as part of the INITIALIZE CONTROL BLOCK command) for
 * INQUIRY, and sends back QUEUE FULL status for any other command.
 *
 */
#define	ISP_ROLE_NONE		0x0
#define	ISP_ROLE_INITIATOR	0x1
#define	ISP_ROLE_TARGET		0x2
#define	ISP_ROLE_BOTH		(ISP_ROLE_TARGET|ISP_ROLE_INITIATOR)
#define	ISP_ROLE_EITHER		ISP_ROLE_BOTH
#ifndef	ISP_DEFAULT_ROLES
#define	ISP_DEFAULT_ROLES	ISP_ROLE_INITIATOR
#endif


/*
 * Firmware related defines
 */
#define	ISP_CODE_ORG			0x1000	/* default f/w code start */
#define	ISP_CODE_ORG_2300		0x0800	/* ..except for 2300s */
#define	ISP_FW_REV(maj, min, mic)	((maj << 24) | (min << 16) | mic)
#define	ISP_FW_MAJOR(code)		((code >> 24) & 0xff)
#define	ISP_FW_MINOR(code)		((code >> 16) & 0xff)
#define	ISP_FW_MICRO(code)		((code >>  8) & 0xff)
#define	ISP_FW_REVX(xp)			((xp[0]<<24) | (xp[1] << 16) | xp[2])
#define	ISP_FW_MAJORX(xp)		(xp[0])
#define	ISP_FW_MINORX(xp)		(xp[1])
#define	ISP_FW_MICROX(xp)		(xp[2])

/*
 * Bus (implementation) types
 */
#define	ISP_BT_PCI		0	/* PCI Implementations */
#define	ISP_BT_SBUS		1	/* SBus Implementations */

/*
 * If we have not otherwise defined SBus support away make sure
 * it is defined here such that the code is included as default
 */
#ifndef	ISP_SBUS_SUPPORTED
#define	ISP_SBUS_SUPPORTED	1
#endif

/*
 * Chip Types
 */
#define	ISP_HA_SCSI		0xf
#define	ISP_HA_SCSI_UNKNOWN	0x1
#define	ISP_HA_SCSI_1020	0x2
#define	ISP_HA_SCSI_1020A	0x3
#define	ISP_HA_SCSI_1040	0x4
#define	ISP_HA_SCSI_1040A	0x5
#define	ISP_HA_SCSI_1040B	0x6
#define	ISP_HA_SCSI_1040C	0x7
#define	ISP_HA_SCSI_1240	0x8
#define	ISP_HA_SCSI_1080	0x9
#define	ISP_HA_SCSI_1280	0xa
#define	ISP_HA_SCSI_12160	0xb
#define	ISP_HA_FC		0xf0
#define	ISP_HA_FC_2100		0x10
#define	ISP_HA_FC_2200		0x20
#define	ISP_HA_FC_2300		0x30

#define	IS_SCSI(isp)	(isp->isp_type & ISP_HA_SCSI)
#define	IS_1240(isp)	(isp->isp_type == ISP_HA_SCSI_1240)
#define	IS_1080(isp)	(isp->isp_type == ISP_HA_SCSI_1080)
#define	IS_1280(isp)	(isp->isp_type == ISP_HA_SCSI_1280)
#define	IS_12160(isp)	(isp->isp_type == ISP_HA_SCSI_12160)

#define	IS_12X0(isp)	(IS_1240(isp) || IS_1280(isp))
#define	IS_DUALBUS(isp)	(IS_12X0(isp) || IS_12160(isp))
#define	IS_ULTRA2(isp)	(IS_1080(isp) || IS_1280(isp) || IS_12160(isp))
#define	IS_ULTRA3(isp)	(IS_12160(isp))

#define	IS_FC(isp)	((isp)->isp_type & ISP_HA_FC)
#define	IS_2100(isp)	((isp)->isp_type == ISP_HA_FC_2100)
#define	IS_2200(isp)	((isp)->isp_type == ISP_HA_FC_2200)
#define	IS_2300(isp)	((isp)->isp_type >= ISP_HA_FC_2300)

/*
 * DMA cookie macros
 */
#define	DMA_WD3(x)	0
#define	DMA_WD2(x)	0
#define	DMA_WD1(x)	(((x) >> 16) & 0xffff)
#define	DMA_WD0(x)	(((x) & 0xffff))

/*
 * Core System Function Prototypes
 */

/*
 * Reset Hardware. Totally. Assumes that you'll follow this with
 * a call to isp_init.
 */
void isp_reset(struct ispsoftc *);

/*
 * Initialize Hardware to known state
 */
void isp_init(struct ispsoftc *);

/*
 * Reset the ISP and call completion for any orphaned commands.
 */
void isp_reinit(struct ispsoftc *);

/*
 * Internal Interrupt Service Routine
 *
 * The outer layers do the spade work to get the appropriate status register,
 * semaphore register and first mailbox register (if appropriate). This also
 * means that most spurious/bogus interrupts not for us can be filtered first.
 */
void isp_intr(struct ispsoftc *, u_int16_t, u_int16_t, u_int16_t);


/*
 * Command Entry Point- Platform Dependent layers call into this
 */
int isp_start(XS_T *);
/* these values are what isp_start returns */
#define	CMD_COMPLETE	101	/* command completed */
#define	CMD_EAGAIN	102	/* busy- maybe retry later */
#define	CMD_QUEUED	103	/* command has been queued for execution */
#define	CMD_RQLATER 	104	/* requeue this command later */

/*
 * Command Completion Point- Core layers call out from this with completed cmds
 */
void isp_done(XS_T *);

/*
 * Platform Dependent to External to Internal Control Function
 *
 * Assumes locks are held on entry. You should note that with many of
 * these commands and locks may be released while this is occurring.
 *
 * A few notes about some of these functions:
 *
 * ISPCTL_FCLINK_TEST tests to make sure we have good fibre channel link.
 * The argument is a pointer to an integer which is the time, in microseconds,
 * we should wait to see whether we have good link. This test, if successful,
 * lets us know our connection topology and our Loop ID/AL_PA and so on.
 * You can't get anywhere without this.
 *
 * ISPCTL_SCAN_FABRIC queries the name server (if we're on a fabric) for
 * all entities using the FC Generic Services subcommand GET ALL NEXT.
 * For each found entity, an ISPASYNC_FABRICDEV event is generated (see
 * below).
 *
 * ISPCTL_SCAN_LOOP does a local loop scan. This is only done if the connection
 * topology is NL or FL port (private or public loop). Since the Qlogic f/w
 * 'automatically' manages local loop connections, this function essentially
 * notes the arrival, departure, and possible shuffling around of local loop
 * entities. Thus for each arrival and departure this generates an isp_async
 * event of ISPASYNC_PROMENADE (see below).
 *
 * ISPCTL_PDB_SYNC is somewhat misnamed. It actually is the final step, in
 * order, of ISPCTL_FCLINK_TEST, ISPCTL_SCAN_FABRIC, and ISPCTL_SCAN_LOOP.
 * The main purpose of ISPCTL_PDB_SYNC is to complete management of logging
 * and logging out of fabric devices (if one is on a fabric) and then marking
 * the 'loop state' as being ready to now be used for sending commands to
 * devices. Originally fabric name server and local loop scanning were
 * part of this function. It's now been separated to allow for finer control.
 */
typedef enum {
	ISPCTL_RESET_BUS,		/* Reset Bus */
	ISPCTL_RESET_DEV,		/* Reset Device */
	ISPCTL_ABORT_CMD,		/* Abort Command */
	ISPCTL_UPDATE_PARAMS,		/* Update Operating Parameters (SCSI) */
	ISPCTL_FCLINK_TEST,		/* Test FC Link Status */
	ISPCTL_SCAN_FABRIC,		/* (Re)scan Fabric Name Server */
	ISPCTL_SCAN_LOOP,		/* (Re)scan Local Loop */
	ISPCTL_PDB_SYNC,		/* Synchronize Port Database */
	ISPCTL_SEND_LIP,		/* Send a LIP */
	ISPCTL_GET_POSMAP,		/* Get FC-AL position map */
	ISPCTL_RUN_MBOXCMD,		/* run a mailbox command */
	ISPCTL_TOGGLE_TMODE		/* toggle target mode */
} ispctl_t;
int isp_control(struct ispsoftc *, ispctl_t, void *);


/*
 * Platform Dependent to Internal to External Control Function
 * (each platform must provide such a function)
 *
 * Assumes locks are held.
 *
 * A few notes about some of these functions:
 *
 * ISPASYNC_CHANGE_NOTIFY notifies the outer layer that a change has
 * occurred that invalidates the list of fabric devices known and/or
 * the list of known loop devices. The argument passed is a pointer
 * whose values are defined below  (local loop change, name server
 * change, other). 'Other' may simply be a LIP, or a change in
 * connection topology.
 *
 * ISPASYNC_FABRIC_DEV announces the next element in a list of
 * fabric device names we're getting out of the name server. The
 * argument points to a GET ALL NEXT response structure. The list
 * is known to terminate with an entry that refers to ourselves.
 * One of the main purposes of this function is to allow outer
 * layers, which are OS dependent, to set policy as to which fabric
 * devices might actually be logged into (and made visible) later
 * at ISPCTL_PDB_SYNC time. Since there's a finite number of fabric
 * devices that we can log into (256 less 3 'reserved' for F-port
 * topologies), and fabrics can grow up to 8 million or so entries
 * (24 bits of Port Address, less a wad of reserved spaces), clearly
 * we had better let the OS determine login policy.
 *
 * ISPASYNC_PROMENADE has an argument that is a pointer to an integer which
 * is an index into the portdb in the softc ('target'). Whether that entrie's
 * valid tag is set or not says whether something has arrived or departed.
 * The name refers to a favorite pastime of many city dwellers- watching
 * people come and go, talking of Michaelangelo, and so on..
 *
 * ISPASYNC_UNHANDLED_RESPONSE gives outer layers a chance to parse a
 * response queue entry not otherwise handled. The outer layer should
 * return non-zero if it handled it. The 'arg' points to an unmassaged
 * response queue entry.
 */

typedef enum {
	ISPASYNC_NEW_TGT_PARAMS,	/* New Target Parameters Negotiated */
	ISPASYNC_BUS_RESET,		/* Bus Was Reset */
	ISPASYNC_LOOP_DOWN,		/* FC Loop Down */
	ISPASYNC_LOOP_UP,		/* FC Loop Up */
	ISPASYNC_LIP,			/* LIP Received */
	ISPASYNC_LOOP_RESET,		/* Loop Reset Received */
	ISPASYNC_CHANGE_NOTIFY,		/* FC Change Notification */
	ISPASYNC_FABRIC_DEV,		/* FC Fabric Device Arrival */
	ISPASYNC_PROMENADE,		/* FC Objects coming && going */
	ISPASYNC_TARGET_MESSAGE,	/* target message */
	ISPASYNC_TARGET_EVENT,		/* target asynchronous event */
	ISPASYNC_TARGET_ACTION,		/* other target command action */
	ISPASYNC_CONF_CHANGE,		/* Platform Configuration Change */
	ISPASYNC_UNHANDLED_RESPONSE,	/* Unhandled Response Entry */
	ISPASYNC_FW_CRASH		/* Firmware has crashed */
} ispasync_t;
int isp_async(struct ispsoftc *, ispasync_t, void *);

#define	ISPASYNC_CHANGE_PDB	((void *) 0)
#define	ISPASYNC_CHANGE_SNS	((void *) 1)
#define	ISPASYNC_CHANGE_OTHER	((void *) 2)

/*
 * Platform Dependent Error and Debug Printout
 */
#ifdef	__GNUC__
void isp_prt(struct ispsoftc *, int level, const char *, ...)
	__attribute__((__format__(__printf__,3,4)));
#else
void isp_prt(struct ispsoftc *, int level, const char *, ...);
#endif

#define	ISP_LOGALL	0x0	/* log always */
#define	ISP_LOGCONFIG	0x1	/* log configuration messages */
#define	ISP_LOGINFO	0x2	/* log informational messages */
#define	ISP_LOGWARN	0x4	/* log warning messages */
#define	ISP_LOGERR	0x8	/* log error messages */
#define	ISP_LOGDEBUG0	0x10	/* log simple debug messages */
#define	ISP_LOGDEBUG1	0x20	/* log intermediate debug messages */
#define	ISP_LOGDEBUG2	0x40	/* log most debug messages */
#define	ISP_LOGDEBUG3	0x80	/* log high frequency debug messages */
#define	ISP_LOGDEBUG4	0x100	/* log high frequency debug messages */
#define	ISP_LOGTDEBUG0	0x200	/* log simple debug messages (target mode) */
#define	ISP_LOGTDEBUG1	0x400	/* log intermediate debug messages (target) */
#define	ISP_LOGTDEBUG2	0x800	/* log all debug messages (target) */

/*
 * Each Platform provides it's own isposinfo substructure of the ispsoftc
 * defined above.
 *
 * Each platform must also provide the following macros/defines:
 *
 *
 *	INLINE		-	platform specific define for 'inline' functions
 *
 *	ISP_DMA_ADDR_T	-	platform specific dma address coookie- basically
 *				the largest integer that can hold the 32 or
 *				64 bit value appropriate for the QLogic's DMA
 *				addressing. Defaults to u_int32_t.
 *
 *	ISP2100_SCRLEN	-	length for the Fibre Channel scratch DMA area
 *
 *	MEMZERO(dst, src)			platform zeroing function
 *	MEMCPY(dst, src, count)			platform copying function
 *	SNPRINTF(buf, bufsize, fmt, ...)	snprintf
 *	STRNCAT(dstbuf, size, srcbuf)		strncat
 *	USEC_DELAY(usecs)			microsecond spindelay function
 *	USEC_SLEEP(isp, usecs)			microsecond sleep function
 *
 *	NANOTIME_T				nanosecond time type
 *
 *	GET_NANOTIME(NANOTIME_T *)		get current nanotime.
 *
 *	GET_NANOSEC(NANOTIME_T *)		get u_int64_t from NANOTIME_T
 *
 *	NANOTIME_SUB(NANOTIME_T *, NANOTIME_T *)
 *						subtract two NANOTIME_T values
 *
 *
 *	MAXISPREQUEST(struct ispsoftc *)	maximum request queue size
 *						for this particular board type
 *
 *	MEMORYBARRIER(struct ispsoftc *, barrier_type, offset, size)
 *
 *		Function/Macro the provides memory synchronization on
 *		various objects so that the ISP's and the system's view
 *		of the same object is consistent.
 *
 *	MBOX_ACQUIRE(struct ispsoftc *)		acquire lock on mailbox regs
 *	MBOX_WAIT_COMPLETE(struct ispsoftc *)	wait for mailbox cmd to be done
 *	MBOX_NOTIFY_COMPLETE(struct ispsoftc *)	notification of mbox cmd donee
 *	MBOX_RELEASE(struct ispsoftc *)		release lock on mailbox regs
 *
 *
 *	SCSI_GOOD	SCSI 'Good' Status
 *	SCSI_CHECK	SCSI 'Check Condition' Status
 *	SCSI_BUSY	SCSI 'Busy' Status
 *	SCSI_QFULL	SCSI 'Queue Full' Status
 *
 *	XS_T		Platform SCSI transaction type (i.e., command for HBA)
 *	XS_ISP(xs)	gets an instance out of an XS_T
 *	XS_CHANNEL(xs)	gets the channel (bus # for DUALBUS cards) ""
 *	XS_TGT(xs)	gets the target ""
 *	XS_LUN(xs)	gets the lun ""
 *	XS_CDBP(xs)	gets a pointer to the scsi CDB ""
 *	XS_CDBLEN(xs)	gets the CDB's length ""
 *	XS_XFRLEN(xs)	gets the associated data transfer length ""
 *	XS_TIME(xs)	gets the time (in milliseconds) for this command
 *	XS_RESID(xs)	gets the current residual count
 *	XS_STSP(xs)	gets a pointer to the SCSI status byte ""
 *	XS_SNSP(xs)	gets a pointer to the associate sense data
 *	XS_SNSLEN(xs)	gets the length of sense data storage
 *	XS_SNSKEY(xs)	dereferences XS_SNSP to get the current stored Sense Key
 *	XS_TAG_P(xs)	predicate of whether this command should be tagged
 *	XS_TAG_TYPE(xs)	which type of tag to use
 *	XS_SETERR(xs)	set error state
 *
 *		HBA_NOERROR	command has no erros
 *		HBA_BOTCH	hba botched something
 *		HBA_CMDTIMEOUT	command timed out
 *		HBA_SELTIMEOUT	selection timed out (also port logouts for FC)
 *		HBA_TGTBSY	target returned a BUSY status
 *		HBA_BUSRESET	bus reset destroyed command
 *		HBA_ABORTED	command was aborted (by request)
 *		HBA_DATAOVR	a data overrun was detected
 *		HBA_ARQFAIL	Automatic Request Sense failed
 *
 *	XS_ERR(xs)	return current error state
 *	XS_NOERR(xs)	there is no error currently set
 *	XS_INITERR(xs)	initialize error state
 *
 *	XS_SAVE_SENSE(xs, sp)		save sense data
 *
 *	XS_SET_STATE_STAT(isp, sp, xs)	platform dependent interpreter of
 *					response queue entry status bits
 *
 *
 *	DEFAULT_IID(struct ispsoftc *)		Default SCSI initiator ID
 *	DEFAULT_LOOPID(struct ispsoftc *)	Default FC Loop ID
 *	DEFAULT_NODEWWN(struct ispsoftc *)	Default Node WWN
 *	DEFAULT_PORTWWN(struct ispsoftc *)	Default Port WWN
 *		These establish reasonable defaults for each platform.
 * 		These must be available independent of card NVRAM and are
 *		to be used should NVRAM not be readable.
 *
 *	ISP_NODEWWN(struct ispsoftc *)	FC Node WWN to use
 *	ISP_PORTWWN(struct ispsoftc *)	FC Port WWN to use
 *
 *		These are to be used after NVRAM is read. The tags
 *		in fcparam.isp_{node,port}wwn reflect the values
 *		read from NVRAM (possibly corrected for card botches).
 *		Each platform can take that information and override
 *		it or ignore and return the Node and Port WWNs to be
 * 		used when sending the Qlogic f/w the Initialization Control
 *		Block.
 *
 *	(XXX these do endian specific transformations- in transition XXX)
 *
 *	ISP_IOXPUT_8(struct ispsoftc *, u_int8_t srcval, u_int8_t *dstptr)
 *	ISP_IOXPUT_16(struct ispsoftc *, u_int16_t srcval, u_int16_t *dstptr)
 *	ISP_IOXPUT_32(struct ispsoftc *, u_int32_t srcval, u_int32_t *dstptr)
 *
 *	ISP_IOXGET_8(struct ispsoftc *, u_int8_t *srcptr, u_int8_t dstrval)
 *	ISP_IOXGET_16(struct ispsoftc *, u_int16_t *srcptr, u_int16_t dstrval)
 *	ISP_IOXGET_32(struct ispsoftc *, u_int32_t *srcptr, u_int32_t dstrval)
 *
 *	ISP_SWIZZLE_NVRAM_WORD(struct ispsoftc *, u_int16_t *)
 */

#endif	/* _ISPVAR_H */