More files which have changed name or location since some time already and

are only confusing things.

1 files changed, 0 insertions, 76 deletions

diff --git a/sys/arch/vax/vsa/ncr.h b/sys/arch/vax/vsa/ncr.h
deleted file mode 100644
index 87a01c7abe6..00000000000
--- a/sys/arch/vax/vsa/ncr.h
+++ /dev/null
@@ -1,76 +0,0 @@
-/*	$OpenBSD: ncr.h,v 1.2 1997/05/29 00:05:35 niklas Exp $	*/
-/*	$NetBSD: ncr.h,v 1.1 1996/07/20 18:55:15 ragge Exp $	*/
-
-/*
- * Register map for the Sun3 SCSI Interface (si)
- * The first part of this register map is an NCR5380
- * SCSI Bus Interface Controller (SBIC).  The rest is a
- * DMA controller and custom logic in one of two flavors,
- * one for the OBIO interface (3/50,3/60) and one for the
- * VME interface (3/160,3/260,etc.), where some registers
- * are implemented only on one or the other, some on both.
- */
-
-/*
- * Some of these registers apply to only one interface and some
- * apply to both. The registers which apply to the Sun3/50 onboard 
- * version only are udc_rdata and udc_raddr. The registers which
- * apply to the Sun3 vme version only are dma_addr, dma_count, bpr,
- * iv_am, and bcrh. Thus, the sbc registers, fifo_data, bcr, and csr 
- * apply to both interfaces.
- * One other feature of the vme interface: a write to the dma count 
- * register also causes a write to the fifo byte count register and
- * vis versa.
- */
-
-/*
- * NCR5380 Register map (byte-registers at longword addresses)
- */
-struct ncr5380regs {
-	volatile u_long sci_r0;		/* 200C.0080: CUR_DATA/OUT_DATA (rw) */
-	volatile u_long sci_r1;		/* 200C.0084: INI_CMD		(rw) */
-	volatile u_long sci_r2;		/* 200C.0088: MODE		(rw) */
-	volatile u_long sci_r3;		/* 200C.008C: TAR_CMD		(rw) */
-	volatile u_long sci_r4;		/* 200C.0090: CUR_STAT/SEL_ENA	(rw) */
-	volatile u_long sci_r5;		/* 200C.0094: STATUS/DMA_SEND	(rw) */
-	volatile u_long sci_r6;		/* 200C.0098: IN_DATA/DMA_TRCV	(rw) */
-	volatile u_long sci_r7;		/* 200C.009C: RESET/DMA_IRCV	(rw) */
-};
-
-struct si_regs {
-	struct ncr5380regs sci;
-};
-
-/* possible values for the address modifier, sun3 vme version only */
-#define VME_SUPV_DATA_24	0x3d00
-
-/*
- * Status Register.
- * Note:
- *	(r)	indicates bit is read only.
- *	(rw)	indicates bit is read or write.
- *	(v)	vme host adaptor interface only.
- *	(o)	sun3/50 onboard host adaptor interface only.
- *	(b)	both vme and sun3/50 host adaptor interfaces.
- */
-#define SI_CSR_DMA_ACTIVE	0x8000	/* (r,o) dma transfer active */
-#define SI_CSR_DMA_CONFLICT	0x4000	/* (r,b) reg accessed while dmaing */
-#define SI_CSR_DMA_BUS_ERR	0x2000	/* (r,b) bus error during dma */
-#define SI_CSR_ID		0x1000	/* (r,b) 0 for 3/50, 1 for SCSI-3, */
-					/* 0 if SCSI-3 unmodified */
-#define SI_CSR_FIFO_FULL	0x0800	/* (r,b) fifo full */
-#define SI_CSR_FIFO_EMPTY	0x0400	/* (r,b) fifo empty */
-#define SI_CSR_SBC_IP		0x0200	/* (r,b) sbc interrupt pending */
-#define SI_CSR_DMA_IP		0x0100	/* (r,b) dma interrupt pending */
-#define SI_CSR_LOB		0x00c0	/* (r,v) number of leftover bytes */
-#define SI_CSR_LOB_THREE	0x00c0	/* (r,v) three leftover bytes */
-#define SI_CSR_LOB_TWO		0x0080	/* (r,v) two leftover bytes */
-#define SI_CSR_LOB_ONE		0x0040	/* (r,v) one leftover byte */
-#define SI_CSR_BPCON		0x0020	/* (rw,v) byte packing control */
-					/* dma is in 0=longwords, 1=words */
-#define SI_CSR_DMA_EN		0x0010	/* (rw,v) dma/interrupt enable */
-#define SI_CSR_SEND		0x0008	/* (rw,b) dma dir, 1=to device */
-#define SI_CSR_INTR_EN		0x0004	/* (rw,b) interrupts enable */
-#define SI_CSR_FIFO_RES		0x0002	/* (rw,b) inits fifo, 0=reset */
-#define SI_CSR_SCSI_RES		0x0001	/* (rw,b) reset sbc and udc, 0=reset */
-